Travis

noriwl

Cosmo Kramers infamous licence plate from Seinfeld. Nice little ornament or gift.

Assman licence plate from Seinfeld

Beppi

SMatty

Hi, I would like to introduce you to my New Phone Stand Raised “Exagon”  Many of you asked me to create a new design of my model Phone Holder Exagon that could allow to connect the phone with charging. This design permits to connect the charging cable to the phone!  I hope you like it. Good Print !&nbsp;If you have any problems with adhesion you can try turning off aux fan when printing PLA&nbsp;You can find the first version here <a target="_blank" href="https://makerworld.com/en/models/193049#profileId-214820" rel="nofollow noopener">https://makerworld.com/en/models/193049#profileId-214820</a>&nbsp;You can find the rivisited version “V2” here<a target="_blank" href="https://makerworld.com/en/models/251302#profileId-267660" rel="nofollow noopener">https://makerworld.com/en/models/251302#profileId-267660</a>&nbsp;If you like my project consider supporting my job with a boost. Thank you !&nbsp;&nbsp;

Phone Holder Raised "Exagon" (allow charging)

Prints

Nates Print Shop

This Tree of Life-themed lithophane was crafted using the Bambu Lab PLA CMYK Lithophane Bundle. It's designed specifically to fit the BL Frame.

Tree of life Lithophane

HueForge

mitchrichie

I’ve been wanting one of these extremely rare German made mid-century mantle clocks but they are really difficult to find and when you do find them they go for $1,000 - $2,500. So I decided to try and 3D print a replica. While not perfect, I like how it turned out.Printed on p1p. For fake wood appearance I did some sanding, then automotive body filler/primer. Then light brown colored spray paint with dark wood stain brushed on for the final coat.&nbsp;For the face of the clock, use ironing to make for a smoother finish. For the clock body, use adaptive layer hight for best results.&nbsp;I used a <a target="_blank" href="https://www.walmart.com/ip/21695068" rel="nofollow noopener">cheap clock movement from walmart</a> as the clock internals. It's a 1/4 in (.63 cm) shaft and a 2.5 in (5.71 cm) housing. The clock movement come with second, min, an hour hands but I discarded those and designed min and hour hands that press fit onto the shaft of the clock movement. &nbsp;The small dots are decoration that press fit into the face of the clock. Same for the narrow strips. You'll need to trim these down to size as you press fit them into the clock. If they are too tight you can play with scaling them down slightly. &nbsp;The original clock had 3 ports used for setting the time and winding the movement. I've included them here has decoration only. Easiest to press fit these in from the back of the face.&nbsp;For the legs, you can place them by eye or do some measuring to get them in the same location on the bottom of the clock body. I may add registration holes at some point.

Mid-Century Welby Mantle Clock 

Project Prints

BamBam Design

Beautiful Lamp 172mm x 247mm with E27 base.

Ceiling Lamp - lampshade E27 base

Lighting

Fat Tony

<h2>V2 Vented Remix - Updated Bambu Lab Ultimate P1P P1S X1-C X1-E Riser+AMS Stand - Community Build!</h2>&nbsp;AMS Riser with ledges half way up the riser so the glass will slide in on top of for easy ventilation when printing PLA. Add LED lighting or stick cheap under cabinet lights to the bottom of the AMS for a simple lighting solution.<ul><li>Rises AMS off machine</li><li>Allows visibility through top glass while printing</li><li>Allows access through top glass for servicing without disconnecting/removing entire AMS</li><li>Shelf allows top glass ventilation to prevent heat creep and clogging during PLA prints</li><li>Minimizes sharpness of PTFE bend radius's helping mitigate “failure to retract” errors</li><li>Stops the PTFE tube from rubbing on the top glass</li><li>Easy to add accessories such as lighting and hooks to hang your build plates</li></ul>&nbsp;03/26/2024: Due to being asked multiple times I have added a plate of just the connectors to the .3mf file. These are separated to reduce the risk of the smaller parts dislodging and ruining the larger prints. Feel free to add them to a plate(s) with the risers as they will fit if you wish.&nbsp;&nbsp;Additional accessories found under raw models. For all accessories and more details, see: https://www.printables.com/model/557492-v2-vented-remix-updated-bambu-lab-ultimate-p1p-p1s&nbsp;

Beppi

Prints

HueForge

Project Prints

Lighting

X1C Prints