Search models, users, collections, and posts
Achievements
MakerWorld Guardian
Active more than 20 days out of last 30 days UTC time
Pioneer Maker
Print successful 165 different models and 2,079 hours
The post is no longer available
Other Issues:Horribly cut up and sized.
After significant changes, resizing, and adding modifiers, I got it to a really nice place. Maybe I'll post a remix if that's allowed, I'll probably forget to though to be honest.
Share
0
0
0
Other Issues:Nothing for this model actually fits together correctly. You can see just how badly this is by measuring the pieces in studio.
I realized, cut, etc.. everything to make it all fit and the print is pretty good now, but as posted, this is a one star model. I'm giving a second for effort, but really shouldn't.
Share
0
0
0
Great print, wife loves them. Printed a topper and one without the loop.
Share
0
0
0
Support Issue:Face keeps falling off.
Reduce support top z, falls off. Reduce layer height, falls off. Do both, falls off. Spent too much time and filament to keep trying, I'll just hang them with their backs in view rather than their faces. Definitely not a monitor buddy now though and really frustrating to spend all the time painstakingly removing the supports for this outcome.
Share
0
0
0
The post is no longer available
Great design and print.
I ended up scaling up to 105% and enlarging the toothbrush holes to fit my son's toothbrushes.
Thank you for an awesome print!
Share
0
0
0
Other Issues:Simply doesn't fit, the posts are not spaced correctly.
that's on top of the wave and boat being lazily added and not flush. I took the time to fix this, then found out the posts are off by several mm after printing.
Waste of time, energy, and filament. Stay away from this one.
Share
0
0
0
Printed great, the extra holder notch is nice, but the separate logo was the real seller for me.
Share
0
0
0
Did not fit my Samsung fridge, was slightly too wide. Mine also does not support magnets, it has a plastic bottom under the water but no tray from factory.
I reduced to 95%, deleted the negative parts for the magnets, and it fits very well.
Five stars because I'm sure it fits your fridge as-is, it was super simple to modify for mine, and the support came away very easily and cleanly.
Thank you for the model.
Share
0
0
0
These could be so cool, but the whole magnet setup is terrible.i even used slightly lafer magnets (thicker) so they would be stronger and it's still janky.
The Kirby Dark Knight and Meta Knight are perfectly done. I wish these were like those.
Share
0
0
0
Stylish, functional, work perfectly.
Use the bearing version, make sure you glue the bearing caps onto the bearings.
Share
0
0
0
Super awesome, so much better than the magnet Kirby models.
Meta Knight came out great. His wings are huge and everything went together perfectly.
Share
0
0
0
Absolutely amazing print.
Share
0
0
0
Other Issues:Welp, there goes four days, three rolls of PTEG, and $60.
I know everyone has different tastes, but the LED integration is not bad, it's horrendous.
No light in front, the rear half of the side channel i
and rear is for a single wire that's about 14 gauge, no LEDs.
The channel for the LEDs is ~6mm in total. only about half or your light strip will actually be seen though due to the sides of the channel covering half the strip to hold it in.
Two strips are needed, you can NOT use just one with the way this is set up, doubling your cost.
Finally, the two recommended light strips will not work, due to the side-rear and rear channels only fitting a single thing wire and the Bambu one is perpetually sold out anyways.
Then the way it clips together in the center of the four pieces is horribly weak. There's holes everywhere with no instructions on their function, maybe a support to hold everything together?
TLDR: Terrible design choices cost me a 6th of my printer's full cost and 4 days.
Share
0
0
0
No more data