TheAustinZombie

PicPac

Made this Bowl/Nail organizer. Fits six 14mm slides/nails. Enlarged the base for heavier pieces, I have printed tons of these and they work great!More versions and sizes coming soon!PLANo Supports15% gyroid infill

6 X 14mm Slidestand

Faran3D

<h3>Welcome to V2 of my Fallout Nuka Cola Series!</h3>This is a series of replicas of the Nuka-Cola drinks from Fallout with the classic rocket shape and fins, and logos and colors matched to the ones you find in game! This is the second version after deciding to make a better bottle and improve the labels.&nbsp;Nuka Wild has a classic Western theme and taste, which we've emulated by adding the graphics from the Bethesda limited edition license plate.&nbsp;Printing is absolutely straightforward - no supports or anything is needed and this is an AMS print so little to no post processing is required.&nbsp;As with all AMS prints it is more economical to print several copies rather than just one, so print a few copies at the same time and use them to decorate several places or give away a few!&nbsp;Please like and rate this print, your support is appreciated!

V2 Fallout Nuka Cola Wild AMS Bottle and Cap

Games

Creatività in 3D

<h2>Special Finger ring!</h2><figure class="image image_resized" style="width:23.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/818863/2024-04-05_407651c21d299.jpg"></figure>Special finger ring that lends itself to multiple uses. Printed with skin-colored iBoss filament In the print profile the inner diameter of the ring is about 22mm for my hands. Resize as needed otherwise it may be too big for some or small for others

Special Finger ring

Trolling

ghostchili3d

Not Today!lucky charm to always have with you

NOT TODAY Keychain

Keychains

crabstiks

A Dawn of the Dead George A Romero movie poster fridge magnet.&nbsp;4 colour AMS print, using black, red, lemon yellow and white.&nbsp;This needs 4x 8mm diameter by 2mm deep magnets, the magnets push into the model after printing, no need to pause.pause.. &nbsp;NOTE - The magnets are designed to be a tight fit. The best way to insert them is to line up a magnet with a hole then place the model on a hard flat surface facing up, with the magnet on the hard surface, then press down firmly on the model. The magnet will snap into place. Repeat for each magnet.

Dawn of the dead Goerge A Romero movie poster fridge magnet

HueForge

Billrobland

This is a basic oversized logo with a loop at the top for chain to attach to. Its just shy of 8 inches wide.

Texans Oversized Chain Necklace

Sports

Stag 3D

<figure class="image image_resized image-style-side" style="width:33.42%;"><img src="https://makerworld.bblmw.com/makerworld/draft/834988/2024-02-08_19ff78005fb62.jpg"></figure><h2>The Friends Iconic Peephole Frame</h2>Add some nostalgia to your door and fit the classic Friends frame. Sculpted to look like the original, with no supports required and a nice simple print. &nbsp;

The Friends peephole frame!

dubmehard

Hello,Doc Brown warning sign.Enjoy

Flux capacitor danger sign

Movies

xsynaticc

Let this distinguished skeleton hand hold the door open for you while your printer is hard at work. Don't worry, he won't try to grab you.&nbsp;Need more?&nbsp;Go visit <a target="_blank" href="https://makerworld.com/en/u/4044076662" rel="nofollow noopener">https://makerworld.com/en/u/4044076662</a>

Skeleton Door holder Bambulab P1S P1P X1C

Printer Upgrades

WhatIsHeBuildingInThere

This is a small corner shelf supported by a skull instead of a conventional bracket.The profile of the shelf is also lined with skull impressions.It also has a small cut-out in the corner to allow a small lamp cord to pass through cleanly. Very cool unique Goth aesthetic home decor.The shelf was also designed with a tapered pocket in the back so it can easily be hung flush on the wall with picture hanging nails.It was printed in Esun black PLA and Esun Bone White.1 color change and a fairly fast print.I've also printed on a rainbow PEY holographic build plate with neat results.Enjoy :)

Skull Corner Shelf

House Decor

Winner3DPrints

Print:-Any layer height -10% infill -no supports&nbsp;Yellow colour is great just like his skin or hair!

Donald Trump Middle Finger Office Accessory tabletop

3d Art

VRsculpts

A cute simple baby octopus with a crochet/knitted look. Keychain file as well as a 3 inch figurine without the keychain hole included in the print profiles. Easy print with minimal color changes, print them in several different colors!&nbsp;The angry octo is based on Dirty Heads “shocktopus” and was originally released via my Patreon but has since been moved to my “vault” on Cults3D.  Joining my Patreon will give you a 50% off coupon code to use on any of my Cults3D files to allow you to purchase previous months models no longer available on the Patreon:https://cults3d.com/en/3d-model/art/crochet-pokemon-mario-vrsculpts-dec-2023-patreon-releases

Octoplush - Amigurumi Baby Octopus Keychain

Crochet

3DPrintable.art

Perfect for Valentine's Day or as a home decor piece.&nbsp;Choose a single color for a classic look or get creative with multiple color combinations.&nbsp;For a perfect smoother surface use <a target="_blank" href="https://wiki.bambulab.com/en/software/bambu-studio/adaptive-layer-height" rel="nofollow noopener">variable layer height</a>. This will increase the print time.&nbsp;Easy print without supports.&nbsp;COMMERCIAL LICENSE AVAILABLE: <a target="_blank" href="https://patreon.com/3DPA" rel="nofollow noopener">https://patreon.com/3DPA</a>&nbsp;Check out <a target="_blank" href="https://makerworld.com/en/u/943536974" rel="nofollow noopener">our other models</a>. Your likes and downloads support more content.&nbsp;Happy printing!&nbsp;

Low Poly Heart

Valentines

kriswillcode

This model of a Poké Ball is easy to print, feels solid, and makes a great cosplay prop. It's easy to assemble and is fun to toss around.When printing, I used a 0.16mm layer height, 15% infill (gyroid), and 2 walls. Supports are not required, but they may help make the front “hole” cleaner.<ul><li>Print the body and button frame in black. </li><li>Print two caps: one in red and one cap in white.</li><li>Print the button in silver.</li><li>Print three pegs in any color.</li></ul>To assemble, use the second photo as a guide. Use glue to hold the ball together. Remember that the pegs are only used for alignment: they're not structural.

Pokemon Poke Ball

Pokemon

boris.sverdlik

Just making some signs for the kid's makerspace area

Warning Illegal Activities in Progress

Signs

3DLabHN

Corona de Lady Loki - Variante de Loki - Sylvie Laufeydottir - para cosplay

Loki crown (Sylvie)

Props & Masks

RobertotE-

Christmas baby yoda, with supports and layer height 0.2. Created with ams from Bambu lab----------------Baby yoda navideño, con soportes y altura de capa 0.2. Creado con ams de Bambu lab

baby yoda christmas xmas navidad Santa Claus Papa Noel

Figures & Figurines

Bottega 3D

For personal use only FOR COMMERCIAL LICENSE: <a target="_blank" href="https://www.patreon.com/bottega3d" rel="nofollow noopener">Patreon</a>. Social Tag: @bottega.3dAMS/MMU available in 3mf file.Love-ly is a cute articulated little dragon. It is printed in place and doesn’t require supports.If you have adhesion difficulties while printing, I recommend using raft or brim. Good calibration and retraction is necessary for a great result.For personal use onlyAll my files are protected by Copyright, should NEVER be shared or resold.To legally sell physical print of my design and if you want to get the latest Models and exclusive designs for your support visit: <a target="_blank" href="http://www.patreon.com/bottega3d" rel="nofollow noopener">www.patreon.com/Bottega3D</a>&nbsp;NOZZLE: 0,4 mm. LAYER: 0.16 or less OUTER WALLS: 3 INFILL: 10% SUPPORTS: NO Z-HOP: 0,4 – 0,8&nbsp;

Love-ly Tiny Dragon, Articulated, Flexy, Toy

Articulated

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;A <a target="_blank" href="https://www.printables.com/model/548840-minecraft-inspired-low-poly-basediorama-builder" rel="nofollow noopener">base/diorama builder</a> is now available for download for this mini figure model!___________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________This is a kit card of Minecraft Fox in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol><h4>Printing Reminders</h4><ul><li>Print as oriented, with NO supports needed.</li><li>If you&#39;re printing in multiple colors, please note that due to several color swaps, it would take longer to print.</li></ul><h4>Difficulty Level (Easy, Medium, Hard)</h4><ul><li>Printing: Hard - Printer should be well calibrated for parts to fit. Bed should be leveled well to ensure small parts stick well to the build plate. Requires printing slower during the first few layers. May require lots of filament swaps if printed in multi-color.</li><li>Assembly: Hard - Parts might be improperly assembled and will be difficult to undo. Refer to assembly guide below.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013270/design/2023-08-16_po9mgd80fph6.png"></figure>

Minecraft-inspired Fox Mini Figure Kit / Keychain

Toys

Willi 3D

Create your own battle droid army and take over the galaxy!&nbsp;If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work bye me a coffee.</a> Thanks!&nbsp;Description:This is a KIT CARD remix of my B1 battle droid. I changed the design in many places to make it easier to assemble and allow the figure to stand and pose on its own. Check out the compatible <a target="_blank" href="https://makerworld.com/de/models/13746?profileId=13457" rel="nofollow noopener">STAP speeder bike</a>!Scale 1:9 (90% for 1:10)&nbsp;Improvements:- improved connection points- easier to assemble- improved stand and pose of the figure- Blaster *pio* *pio*- kit cardsMay the force be with you!Roger roger!&nbsp;Update:(21/08/23) <ul><li>optimized base</li></ul>(03/08/23) <ul><li>optimized size for smaller printer and better to print fingers</li><li>addet base and insert to chest </li></ul>(26/07/23) <ul><li>optimized fit of head, thin, pipe, backpack and blaster</li><li>addet thumb to forarm, hole for blaster in backpack</li></ul>(13/07/23) <ul><li>optimized fit of ankle and blaster</li></ul>&nbsp;Printing:Layer height: 0.1Supports: NoBrim: NoMaterial: PETG, (ABS), (PLA)&nbsp;Assembly: The connections are designed and optimized for PETG, the use of PLA or ABS makes assembly more difficult.It is better to rotate the knee and elbow joints than to push them into place.In order to replicate the design of the B1 battle droid as closely as possible, I was forced to make some parts very fragile. Please be ready to reprint parts in case of breakage. Separate parts are located in the respective folders.

Kit Card B1 Battle Droid Star Wars 

Kit Cards

TripleGWorkshop

<h4>Modular Design.</h4><figure class="image image_resized" style="width:78.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/119940/2023-10-25_qmbowfau371w.jpg"></figure><h4>Room for fuzzy skins.</h4><figure class="image image_resized" style="width:77.99%;"><img src="https://makerworld.bblmw.com/makerworld/draft/119940/2023-10-25_oml34vcgadbg.jpg"></figure><h4>Drain Reservoir in back.</h4><figure class="image image_resized" style="width:77.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/119940/2023-10-25_z3eyiggo8vua.jpg"></figure><h4>Enjoy!</h4><figure class="image image_resized" style="width:82.07%;"><img src="https://makerworld.bblmw.com/makerworld/draft/119940/2023-10-25_59ql00txs3ts.jpg"></figure>No time? Here's a VASE MODE version that prints fast! <a href="https://www.printables.com/model/464081-hex-tiered-planter-vase-mode" rel="nofollow">https://www.printables.com/model/464081-hex-tiered-planter-vase-mode</a><figure class="image image_resized" style="width:66%;"><img src="https://makerworld.bblmw.com/makerworld/draft/119940/2023-10-25_qlkz47q5neoi.jpg"></figure>

Pop-Out Hex Herb Garden w/Drainage

Planters, Vases, Cups, Storage

PAPA Emeritus IV

Friend wanted Toyota Supra keychain so I made a quick one for him. Throw it up for anyone that wants to use it as well&nbsp;

Toyota Supra Keychain

Vehicle / Car Show

JamesThePrinter

Print-in-place chain link fidget toy - available in 4 sizes. <ul><li>Small (8 Links) - Ideal for one-handed use</li><li>Medium (12 Links) - Good middle ground, useable in one or two hands (Recommended)</li><li>Large (16 Links) - Great for use with two hands</li><li>XL (40 Links) - No real purpose, just for fun!</li></ul>You can roll, twist, curl the chain inside your hand(s) and make interesting shapes. For Medium and Large sizes, place it on two fingers and rotate the chain around, as if you were twiddling your thumbs. No special settings are required for these models. However, the joints may need broken in, depending on the accuracy of your printer.&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The filaments used in the pictures above:Small - polymaker PolyTerra Marble PLA Small - Fillamentum Wizard's Voodoo PLAMedium - Inland Blue Tough PLALarge - polymaker PolyTerra Army Red PLALarge - Inland Yellow Tough PLAXL - Fillamentum Lilac PLA

Chain Link Fidget (Print-In-Place)

Fidgets 

TomoDesigns

Have you ever heard of an Easter egg that contains a small middle finger inside? This cheeky hidden feature is a playful surprise on easter. And hopefully get a laugh and smile!You don't need to use any supports. Used materials: <a href="https://amzn.to/3MdzstI" rel="nofollow">Yellow PLA</a>I gave you this design so maybe you can help me? Are you passionate about finding solutions for the 3D printed waste problem? Help me with my research by<a href="https://www.instagram.com/tomo_designs/" rel="nofollow"> sharing a photo</a> of your 3D printed waste bin or pile and let's work together towards a more sustainable future. You can also just dm me on Printables!Every make will be featured on my Instagram if you add your handle and follow me :) Check out <a href="https://www.instagram.com/tomo_designs/" rel="nofollow">my Instagram</a> if you want to see more designs like this or if you have questions!Do you want to support me or become a reseller of my designs? Go take a look at my <a href="https://www.patreon.com/TomoDesigns" rel="nofollow">Patreon!</a><figure class="media"></figure><a href="https://www.printables.com/model/305181-mini-flip-middle-finger-keychain/files" rel="nofollow"><img src="https://media.printables.com/media/prints/321974/rich_content/e73a35dc-3eb6-4b8e-8868-562097445e34/thumb.png#%7B%22uuid%22%3A%220377c536-6b0b-4a83-8e62-cf1d4c413d47%22%2C%22w%22%3A3648%2C%22h%22%3A2736%7D"></a><a href="https://www.printables.com/model/358469-middle-finger-happy-pot" rel="nofollow"><img src="https://media.printables.com/media/prints/430214/rich_content/76efd913-8ca8-4bd4-b384-81c028f0d737/thumb.jpg#%7B%22uuid%22%3A%22a2b198e8-e124-4e9f-b5e6-466fb371a838%22%2C%22w%22%3A3648%2C%22h%22%3A2736%7D"></a>

Middle Finger Easter Egg

Easter

Chester3D

&nbsp;IntroductionThe original model is designed for printers with a 250x250mm bed.&nbsp;If for any reason it doesn't fit on your bed, you can resize the model to the size you want from your slicer.&nbsp;It consists of two parts, the lamp body (body.3mf) and the rear cover (lid.3mf).Sometimes I include two lids, with and without a hole (choose the one you want, I recommend printing the Lid with hole whenever possible, to be able to remove the LED cable).&nbsp;If the back cover does not have a hole, you can easily make it from Bambu Studio, or from any other slicer you use.&nbsp;----&nbsp;You will need&nbsp;<ul><li>LED Strip: <a target="_blank" href="https://s.click.aliexpress.com/e/_DFOBtHT" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DFOBtHT</a></li><li>- Glue gun or Tape</li></ul>Optional, but recommended:&nbsp;<ul><li>Aluminum tape: <a target="_blank" href="https://s.click.aliexpress.com/e/_DEPgqHd" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DEPgqHd</a></li><li>- Textured PEI Sheet</li></ul>----&nbsp;Assembly instructions&nbsp;&nbsp;You can follow either of these two videos to assemble the lamp. It's very simple, you stick the LED strip inside and that's it. If you want, you can use aluminum tape to improve the lighting, although it is not necessary: &nbsp;<ul><li>Assembly instructions by braga3dprint: <a target="_blank" href="https://www.youtube.com/watch?v=QNsShLmXYh0" rel="nofollow noopener">https://www.youtube.com/watch?v=QNsShLmXYh0</a> (He makes very beautiful designs, you can leave him a follow and help him grow his channel!)</li><li>- Another assembly instructions: <a target="_blank" href="https://www.youtube.com/watch?v=nDUlBp7Mm1c----" rel="nofollow noopener">https://www.youtube.com/watch?v=nDUlBp7Mm1c----</a></li></ul>----&nbsp;Printing settings&nbsp;Following braga3dprint recommendations, you can start with these settings in Bambu Studio:<ul><li>Preferences (CTRL + P) → Activate developer settings → Quality → Advanced → First Layer Flow Ratio: 1.04</li><li>- Quality → Wall generator → Arachne</li><li>- Quality → Wall transitioning threshold angle → 50 degrees</li><li>- Strength → Advanced → Infill/wall overlap → 20%</li><li>- Quality → Advanced → Avoid crossing walls</li><li>- Increasing retraction / reducing temperature can help reducing wisps</li><li>- Order color printing from lightest to darkest color</li></ul>Important! Remember to remove the purge line at the start printing, otherwhise it will ruin the print.&nbsp;

Homer Simpson LED Lamp

Lightboxes

Chris Pirillo

Once upon a time in a cozy pizzeria nestled on a charming street corner, something extraordinary happened. A simple slice of pepperoni pizza, freshly baked and just out of the oven, came to life in a whimsical turn of events.&nbsp;The pizzeria, known for its magical ambiance and delicious pies, had an ancient recipe passed down through generations. It was said that the recipe contained a dash of stardust, the secret ingredient that gave life to the most extraordinary slice of pizza.&nbsp;One busy evening, as the chef expertly twirled pizza dough in the air, a shooting star streaked across the night sky. The stardust fell through an open window and landed right on a slice of pepperoni pizza, just as it was being placed on a tray. The slice began to tremble and then, to the astonishment of the chef, the servers, and the customers, it sprouted a tiny face made of melted cheese and two olive eyes.&nbsp;The little slice of pizza, whom the chef named Pep, hopped off the tray and landed on the countertop. Pep, the talking slice of pizza, had a delightful personality. He was cheerful, humorous, and had an insatiable curiosity about the world outside the pizzeria.&nbsp;Word quickly spread about Pep, and soon, the pizzeria became a famous and bustling spot. People from near and far came to see the talking slice of pizza and have a chat with him. Pep became a beloved figure in the neighborhood, and he was always ready with a witty remark or a pizza-related joke.&nbsp;Pep's existence also brought about some changes in the pizzeria. It became a place where food came to life. The vegetables on the pizza started telling stories about their farms, the olives discussed their Mediterranean adventures, and the cheese shared tales from the dairy. It was a lively and heartwarming atmosphere.&nbsp;Pep's days were filled with laughter and chatter, and his nights with the shimmering stardust above. Life was quite magical for a slice of pepperoni pizza.&nbsp;As the years passed, the pizzeria remained a cherished spot where people came not just for the delicious pies but for the warm, friendly atmosphere and the extraordinary slice of pepperoni pizza that had come to life through a touch of stardust. Pep's story became a legend, a tale told to children before bedtime, reminding everyone that magic could be found in the most unexpected places, even in a humble slice of pepperoni pizza.&nbsp;Rendered in Midjourney, prepped in HueForge, and printed at 0.08mm layer height:<ul><li>Deep Red to Layer 7</li><li>Translucent Orange to Layer 12</li><li>Translucent Yellow to Layer 18</li><li>Cream to Top Layer</li></ul>&nbsp;

Pepperoni Pizza Print Prank

Fake Food

MKCAMC

I designed this version 2 of my Stackable Low-Profile Egg Dispenser in resopnse to feedback that I recieved from several people. This version is split into 2 parts which allows it to be printed on small format printers such as the A1 Mini and many others. I also increased the overall assembled length of the dispenser in order to allow for 6 eggs to be placed in it rather than 5. As in the original there is a slop to feed the eggs forward and a lip to keep them from falling out. Assembly is easy. Apply glue to either piece and then line up the fins and slots in between the 2 halves. You can print and stack as many of these as you need. I'm including a profile that has a brim and a profile that doesn't have a brim. I recommend using the brim, but it will take a little post processing to kae sure the brim material is cleared out so each section can stack. Enjoy!

Longer Stackable Egg Dispenser

Handy House Items

bkprint3d

License available through <a target="_blank" href="https://www.patreon.com/bkprint3d" rel="nofollow noopener">patreon</a>.

Business Card Holder

Vending

cruse2382

the nightmare before Christmas jack and sally hearts bauble

X-Mas

Williams Industries

Fun layered skeleton hand wall art&nbsp;I have a lot of fun things over on my Patreon, including commercial license for all files: https://www.patreon.com/WilliamsIndustries

Skeleton Hand

Wall Art

Toys_And_Stuff

Made this for holding business cards on the side of my photo booth.It's mounted with three screws

Handy Devices

Layered/textured bat &nbsp;Check out all of our great fun stuff over on our Patreon: https://www.patreon.com/WilliamsIndustries

420