TechJeeper

Gulsifer

This is a print in place Bambu Lab Duct for the X1C, P1P, P1S, and P1E.&nbsp;The supports are already added on the vent area and will need to be removed after printing. see photo posted<ul><li>A 3mf file has been provided painted and not panted version</li><li>total grams used for this print is 12.76</li><li>using standard setting for Bambu it will print in under 1h</li></ul>&nbsp;The model is scaled to ABS and ASA standards.<ul><li>it has been tested on a P1S and a X1C.</li></ul>this model requires (2) 4x2mm magnets if you want the base to magnetize to the existing shroud.&nbsp;please be aware that to install this you might have to gently remove some glue around the edge of the plastic. some shrouds and ducts are glued in place. also the two fasteners that hold the existing duct in place are meant to be reused on the new duct.&nbsp;Why this duct. it centralizes the air around the nozzle and dose not blow the air to one side like the original duct. it also improves the overall localized flow. It uses Laminar flow to make the air more stable as it gets to the cooling area.&nbsp;Special thanks to JoeMikeMakes for beta testing this on his X1C&nbsp;Please Note: I have added a new .stl version and updated the .3mf file with the Right magnet removed “Bambu G Duct Lidar Void UPDATE” for more clearance for the lidar camera and sensor on the X1C. This prevents the printer from giving a errors that the lidar is covered. I have created Built in support that will need to be removed on the lidar side.

Bambu G Duct

Printer Mods

TripleGWorkshop

Delicate but surprisingly easy to print. If you have a thin side that is likely due to cooling direction.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/130184/2023-10-27_b3v7i9peznpu.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/130184/2023-10-27_v17jr20wwvk2.jpg"></figure>

▤ Air Trees (easy) Bridging Demo

Christmas

K2_Kevin

<h2>The K2 Clip - WATCH THE VIDEOS BELOW!</h2>The K2 Clip is a unique design with multiple locking points. No matter what, there will be a locking point facing up. The clip can be left to &#34;float&#34; on your filament spool while printing. Extra secure storage using the locking center version! NOTE: I recommend taking them off when using the Bambu AMS. &nbsp;⭐️Don&#39;t forget to Follow! Thank you so much for your Downloads, Like and BOOSTS!&nbsp;NOTE: All printers are different, and calibrated differently. The K2 Clip has very tight tolerances. Test print one in case you need to scale the X/Y up or down.______________________________________________________________________________________________&nbsp;❤ How-To by FilamentStories ❤  <a target="_blank" href="https://www.youtube.com/watch?v=xv6aaTB9OwY&amp;ab_channel=FilamentStories" rel="nofollow noopener">https://www.youtube.com/watch?v=xv6aaTB9OwY&amp;ab_channel=FilamentStories</a><figure class="media"><oembed url="https://www.youtube.com/watch?v=xv6aaTB9OwY&amp;ab_channel=FilamentStories"></oembed></figure>&nbsp;&nbsp;<h3>JJ Shankles Video: <a target="_blank" href="https://youtube.com/shorts/xuDetHdQee8" rel="nofollow noopener">https://youtube.com/shorts/xuDetHdQee8</a></h3><figure class="media"><oembed url="https://www.youtube.com/shorts/xuDetHdQee8"></oembed></figure>&nbsp;&nbsp;❤ Featured on <a target="_blank" href="https://www.youtube.com/watch?v=koAZ6oNUyHo" rel="nofollow noopener">BV3D: Bryan Vines</a> “3D Printed Tools for 3D Printing” @ 06:15s<figure class="media"><oembed url="https://www.youtube.com/watch?v=koAZ6oNUyHo&amp;ab_channel=BV3D%3ABryanVines"></oembed></figure>&nbsp;&nbsp;<h3>Don&#39;t forget to ❤ Like and ★ Rate!</h3><h3>Q&amp;A:</h3><ul><li>How do I use the K2 Clip?<ul><li>Insert the end of your filament through the center hole and feed the clip around your spool until the end of your filament again meets up with your K2 Clip.</li><li>Press the end of your filament into the top of the K2 Clip.</li></ul></li><li>Why so tight?!?! It&#39;s designed to be tight and hold your filament firmly. The K2 Clip will loosen after some use.</li><li>Why is it a triangle? Triangles are cool! No matter what, there will be a locking point facing up.</li><li>Should I remove the clip while printing? In your AMS, I would, otherwise Heck NO! I took lots of time designing/sizing/shaping/massaging that center hole to float on your spool while printing.</li></ul>&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014538/design/2023-11-21_a81da16fabaa3.png"></figure>

Printer Mods

Christmas

Cool Stuff!