TBSE Engineering

jarvizar

3D miniature of Midtown Manhattan!&nbsp;Model spans from the East River to the Hudson river & 25th St. to 60th St.&nbsp;&nbsp;Check out my collection of other Large miniature cities: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/468505" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/468505</a>&nbsp;New York City miniatures collection: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/177621" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/177621</a>&nbsp;&nbsp;This model was designed to be printed with a 0.4mm nozzle and 0.16mm layer heights. Try using a 0.2mm nozzle (0.08mm layer heights) or scaling up for even finer detail!&nbsp;Note: If roads or other small details disappear after slicing, try lowering the extrusion/line width of external perimeters (outer walls) closer to 0.4mm OR use Arachne walls.&nbsp;<h2>Framing Details</h2>&nbsp;This model measures almost exactly 7.5x9.5in (241.32mm X 191.08mm) and should fit most 8x10 frames (assuming frame lip/overlap is around a half-inch). Feel free to change the scale/size of the model(s) to meet your needs.&nbsp;Personally I use these cheap wooden frames from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B08XVP48KQ" rel="nofollow noopener">https://www.amazon.com/dp/B08XVP48KQ</a>And blue printer paper: <a target="_blank" href="https://www.amazon.com/Astrobrights-491618-Multipurpose-8-5-Inch-11-Inch/dp/B00006IDQT" rel="nofollow noopener">https://www.amazon.com/dp/B00006IDQT</a>&nbsp;I also included a large printable frame (w/ 1mm water plate) designed to fit my large miniature cities.&nbsp;Note: This is a “large” miniature and will not fit the smaller ~5x7inch printable frame included with the other miniature cities!&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;

New York City Manhattan (Large 8x10)

Cake3d

Hey there, I've designed this model to store my most common used tools, glue, consumables and parts for my printers. Slots for an isopropyl bottle, Elmer's and Bambu supplied glue at the left side but coincidentally the centre cut out for the top glass knob is the perfect size for Elmer's too. Plenty of slots on the right for scrapers, pliers, tweezers, unclogging pins and snips including a dedicated slot for the Bambu scraper that comes with the Printer. Middle and front has room for spare parts. This model has been very popular on Printables and downloaded over 6000 times so I must've done something right.After some suggestions from some people on the Bambu FB group I've added the ability to install a small LED light and cable management underneath the storage to improve the much needed lighting in the printer but currently it only allows a small light bar approx 190x25mm. I do plan on rearranging and removing some slots to allow for a bigger light bar in near future so if you have suggestions for a popular or common light bar please comment and I'll try make it fit. I'd also consider requests/suggestions for specific tool or part slots.The Model fits the dimensions of the X series perfect but also works great on P Series, it sits over the glass door knob and hugs each side of the AMS so will not move and cannot be knocked off. Cut outs are for the X1C touchscreen and the pointless buttons.It's split into two parts that lock together (no tools screws or glue required) so that this can be printed within the X and P series build dimensions. <figure class="media"><div data-oembed-url="https://youtube.com/shorts/gx0XCUPGt9c?feature=share"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=gx0XCUPGt9c"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/gx0XCUPGt9c" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>I've also more recently designed a similar storage optimised for the P Series but is still a great alternative for the X Series but it has some extra features such as phone/tablet stand, much bigger and modifiable modular slots that you can swap to suit or make specific tool holders. Link to that model is > <a target="_blank" href="https://makerworld.com/en/models/38428#profileId-37257" rel="nofollow noopener">https://makerworld.com/en/models/38428#profileId-37257</a>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/264669/2023-12-13_687eb38f33a71.jpg"></figure>&nbsp;PRINT SETTINGSI highly recommend you print using my STRONG and NEAT print profile as it's tried and tested. My Settings used are below to make this strong and solid but if you want to save an hour or two you do you, top/bottom layers and walls can be reduced to save time and plastic. you're looking at 10-12 hours print time with exactly 0.5kg filament used. I personally printed both parts separately as it is a long print however both parts can be printed at the same time on one build plate and worked great, my print profile contains build plates with both on and also with them separated one part per plate. I recommend eSun PLA+ silver for a good match for the X series printers and Filament PM PLA+ matte black for the P series. I've included build plates of the model in parts or together just pick which you want.4 walls (.4 nozzle)0.2 layer height6 bottom 6 top layers15% gyroid infillTURN OFF AUX FAN TO AVOID WARPING -brim not used in this profile, use brim if you want but it'll probably make joining the parts together more difficult if the brim isn't removed fully.This is designed NO SUPPORTS REQUIRED, no issues when I printed mine some bridging wasn't pretty but it's all hidden underneath, clean from above and strong. &nbsp;&nbsp;Hope you love the model, all I ask in return is you hit like if you do. I would love for you to share your make on here and leave a review it means a lot to me. &nbsp;&nbsp;&nbsp;User Lakopet has created an adaptor to allow this storage to fit perfectly to the side of the printer, rather than on top.<a target="_blank" href="https://makerworld.com/en/models/15641#profileId-16038" rel="nofollow noopener">https://makerworld.com/en/models/15641#profileId-16038</a>&nbsp;Please also respect the license - this is for personal use only.

Top Tool Storage for Bambu Lab X1C X1 P1S P1P printers with AMS

Printer

mitchrichie

I’ve been wanting one of these extremely rare German made mid-century mantle clocks but they are really difficult to find and when you do find them they go for $1,000 - $2,500. So I decided to try and 3D print a replica. While not perfect, I like how it turned out.Printed on p1p. For fake wood appearance I did some sanding, then automotive body filler/primer. Then light brown colored spray paint with dark wood stain brushed on for the final coat.&nbsp;For the face of the clock, use ironing to make for a smoother finish. For the clock body, use adaptive layer hight for best results.&nbsp;I used a <a target="_blank" href="https://www.walmart.com/ip/21695068" rel="nofollow noopener">cheap clock movement from walmart</a> as the clock internals. It's a 1/4 in (.63 cm) shaft and a 2.5 in (5.71 cm) housing. The clock movement come with second, min, an hour hands but I discarded those and designed min and hour hands that press fit onto the shaft of the clock movement. &nbsp;The small dots are decoration that press fit into the face of the clock. Same for the narrow strips. You'll need to trim these down to size as you press fit them into the clock. If they are too tight you can play with scaling them down slightly. &nbsp;The original clock had 3 ports used for setting the time and winding the movement. I've included them here has decoration only. Easiest to press fit these in from the back of the face.&nbsp;For the legs, you can place them by eye or do some measuring to get them in the same location on the bottom of the clock body. I may add registration holes at some point.

Mid-Century Welby Mantle Clock 

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014267/design/2023-09-19_1c59e405d0a79.png"></figure>This is a V-twin engine model that consists of various parts like a crankshaft, connecting rods, camshafts, gears, and a throttle valve, among others. It can replicate the functioning of a real engine. The engine model has magnetic decorative covers and hollowed-out structures that make it easy to observe the internal parts. It can be rotated using either a manual crank or an electric motor. In manual mode, the engine runs at a slow pace, allowing for a better observation of each movement. With the motor drive mode, the engine can run continuously by using the motor to rotate the crankshaft.&nbsp;Recommended filaments: Bambu PLA series, PLA Basic is recomended especially in moving parts<a target="_blank" href="https://store.bambulab.com/products/pla-basic-filament?variant=40820833517683" rel="nofollow noopener">https://store.bambulab.com/products/pla-basic-filament</a>Hardware Kit: Engine Model Components Kit-005<a target="_blank" href="http://store.bambulab.com/products/engine-model-components-kit-005" rel="nofollow noopener">http://store.bambulab.com/products/engine-model-components-kit-005</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the video tutorial step by step to print and assemble your build. <figure class="media"><div data-oembed-url="https://youtu.be/wv3qnfMbuko"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/wv3qnfMbuko" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

NYC

Printer

Fun

Engine