Silicon

hectorri

Remix of @Isambard model with double height drawer.&nbsp;&nbsp;

6U & 14U Gridfinity Modular Drawer System

Gridfinity

mcmaven

This Print Profile includes all the components you need to upgrade your AMS to use loose (silica gel) desiccant. And the additional Dry Pods allow the AMS to hold more desiccant, which will mean longer times between refreshes.&nbsp;This has been done before, in many different combinations, but I couldn&#39;t find one that met all my needs. I feel that this remix contains the best combination of AMS Dry Pod and Desiccant Containers that are currently available, and I added a Funnel to help load them with silica.  There are 3 parts included that can hold the hygrometer, only print one: 1) a Shallow Hole version with slots for the hygrometers with 30 degree tabs that can hold more desiccant, 2) a Shallow Hole version with slots for the hygrometers with vertical tabs that can hold more desiccant, and 3) a Thru Hole version with 30 degree slots for the hygrometer tabs, designed by FLAP_design, where the hole for the hygrometer goes all the way through the pod. This version holds desiccant in the Dry Pod, but it can generate a more accurate reading because it will be measuring the overall AMS humidity, rather than the humidity of the desiccant in the Dry Pod with the hygrometer, i.e., the readout is less likely to be be distorted by the silica close to the reader.&nbsp;Just drag your preferred option onto the build plate.  The Round Hygrometer can be found here: <a target="_blank" href="https://www.amazon.ca/Hygrometer-Thermometer-Humidifiers-Dehumidifiers-Greenhouse/dp/B07BLQMR97" rel="nofollow noopener">https://www.amazon.ca/Hygrometer-Thermometer-Humidifiers-Dehumidifiers-Greenhouse/dp/B07BLQMR97</a>&nbsp;The Desiccant Containers can be loaded with generic desiccant and dropped into the slots in the back of the AMS. The top of the Desiccant Containers is split into two parts. The lower part should be glued on, and the upper snapped in after desiccant is added. They are easy to remove and replace the desiccant in.&nbsp;I used this desiccant: <a target="_blank" href="https://www.amazon.com/gp/product/B07QRRHJV3" rel="nofollow noopener">https://www.amazon.com/gp/product/B07QRRHJV3</a>&nbsp;To refresh the desiccant; pour it into a glass tray, place in the microwave for 2 minutes. Let it cool, then pour it back into the Dry Boxes. DO NOT put the Dry Boxes in the microwave! The desiccant gets VERY hot and will melt the Dry Boxes.&nbsp;Note that the Dry Pods will also work with the Hydra spool tray.Or if you are using the factory Bambu AMS spool tray then after inserting the Desiccant Containers, the original AMS dessicant covers can be snapped on top of them.&nbsp;With fresh desiccant, the humidity was down to 10% after a couple of hours, and it has stayed there for over 2 months now.&nbsp;24/4/7Added Pod for round hygrometers with vertical tabs.&nbsp;24/06/13V3.3 version adds an extension to the Funnel that allows it to cover Wide Dry Pods so desiccant is not lost when filling them. The same Funnel works also with Narrow Dry Pods.&nbsp;

AMS Dry Pods Wide, Narrow, Hygro, Trays, & Funnel

Bambu

Think3D

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. Start with Black At layer #10 (0.88mm) swap to Blue At layer #15 (1.28mm) swap to Red At layer #22 (1.84mm) swap to Jade White for the rest.&nbsp;___________________________________________________________________________________If you like my work, please consider a small donation :) Thank you very much :*<a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=RWRXKCAEM86K8" rel="nofollow noopener">https://www.paypal.com/donate/?hosted_button_id=RWRXKCAEM86K8</a>&nbsp;

Trunks - HueForge

HueForge

Jangyy

<div><h1>Summary</h1><div>Lidl Glider Pusher Power PodDesigned for 12 x 12 mm M2 hole mount. I used a Racerstar Racing Edition 1806 motor with a 4" prop.Designed to be printed with no supports. To make it stronger, print at a higher temperature. V2 is for motors shaft that stick out past the motor base.For the 12 x 16 mm mount <a href="/thing:5585789" rel="nofollow">https://www.thingiverse.com/thing:5585789</a>For the 16 x 19 mm mount <a href="/thing:5624386" rel="nofollow">https://www.thingiverse.com/thing:5624386</a>My set-up 3S 1000mah lipo 3 x 5 gram servos 3 bladed 4 inch prop Racerstar Racing Edition 1806 75 watts at full power 25a ESC All up, weight 320gFlight video <a href="https://youtu.be/dKA-KWGKGeA" rel="nofollow">https://youtu.be/dKA-KWGKGeA</a></div><h1>Print Settings</h1>Rafts: <div>No</div> <pre><code> Supports: <div>No</div></code></pre> Resolution: <div>200</div> <pre><code> Infill: <div>20</div></code></pre> Filament: <a href="http://www.amazon.com/s?url=search-alias&field-keywords=ESUN+PLA+%2B" target="_blank" rel="nofollow noopener"> ESUN PLA + </a><pre><code> orange Notes: <div>Printed at 215 degrees</div></code></pre></div>