Shiro

BenniBiene

<h2>608 ball bearing</h2>

608 ball bearing

材料

Eleazar 3DinPlastic

Maker World does not allow you to upload a 3mf with custom Gcode, in the fifth image you can see the command that you must use for temperature changes, it is added in the right bar as custom G-code: “M104 S[Target temperature]”&nbsp;Customised layered G-Code: - layer 44: M104 S225 - layer 84: M104 S220 - layer 124: M104 S215 - layer 164: M104 S210 - layer 204: M104 S205 - layer 244: M104 S200 - layer 284: M104 S195 - layer 324: M104 S190&nbsp;In this image you can see how to enter the custom Gcodes to set the printing temperature manually, you must also choose the maximum temperature as the printing temperature in the profile of your filament.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/862671/2024-03-11_88f8890a06961.webp"></figure>&nbsp;&nbsp;Towe Temp for PLA 230-190ºCTower Temp for ABS 270-230ºCTower Temp for PETG 250-220ºC&nbsp;<a target="_blank" href="https://makerworld.com/en/models/56371#profileId-57990" rel="nofollow noopener">If your tower has a lot of threads between the cones, you can try printing this design and calibrate your retractions, I hope it helps!</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/862671/2024-03-11_f215cb148d647.webp"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/240794#profileId-256732" rel="nofollow noopener">NEW MODEL AVAILABLE</a>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/862671/2024-03-11_c42e9c53b8b2a.png"></figure>&nbsp;&nbsp;&nbsp;

Tower Temp / Temperature Tower Test -PLA-ABS-PETG

测试

chameko小廢物電波塔

<blockquote>12/06 After many tests, I successfully found out the cause of the assembly problems reported by some users, and modified the side panel file "AMS Dry Box-SW_v2".NOTE!I Designed this model not only for ams, I also used it in the vacuum bag that holds the filament, so I needed tight tolerances to make the box strong enough. The tolerance is 0.3mm, please be sure to confirm before printing this model.</blockquote>Open the side lid and pour about 60g of silica.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_92a6870d48198.jpeg">&nbsp;There is a buckle design on the top, please make sure it is buckled correctly when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_2f71bc9cf33e9.png">&nbsp;&nbsp;The front and back of the V2 version have relaxed tolerances in most areas, making it easier to install. I kept the last small area because without this part, you might get the box and slide it open like in the second picture, resulting in a mess.Please be careful not to install it in the wrong direction when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_fcf2db2bab532.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_210d78c4699ec.jpeg">&nbsp;If you have trouble assembling them, try using a heavy object to knock them into the correct position.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_e0f13f6121362.jpeg">&nbsp;As for why I used this complex design, it was because I considered that he had to withstand several kilograms of impact from the filament, so I wanted to distribute the force as equally as possible to each part.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_90a605e9c843e.png"> <blockquote>Also I have a beautiful model related to AMS! Don’t miss it!</blockquote><figure class="image image_resized image-style-side" style="width:56.75%;"><a href="https://makerworld.com/zh/models/99476#profileId-106044" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-23_3d850a0169288.jpg"></a></figure>Do you always find the AMS feeder difficult to press? Are the models on the Internet very difficult to install? I have improved and carefully designed this model. Please be sure to try it!(click on the image to go to the page!)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<blockquote>----------中文解說----------</blockquote>打開側蓋後約可倒入60g的乾燥劑. 上方具有卡扣設計,安裝時請確認有正確的扣上.&nbsp;V2版本的正面與背面放開了大部分區域的公差,使其較容易安裝. 我保留了最後一小區域,因為沒有這個部分的話,你可能再拿取盒子時像第二張圖一樣滑開,導致一團糟. 安裝時請注意不要裝錯方向.&nbsp;如果你在組裝上遇到了困難,可以嘗試使用重物敲擊他們使其安裝至正確的位置. 至於為什麼使用這種複雜的設計,是因為我考慮到他必須承受數公斤來自線材的撞擊,因此我想盡可能地讓力量平均分攤到每個部分.

AMS Silica Gel Box[V2]

工具

hfts.rider

Storage box, nothing special) Size: 22x18x8 cm

Storage box

家居

niltsh

This is the updated version of <a target="_blank" href="https://makerworld.com/zh/models/39368#profileId-38480" rel="nofollow noopener">https://makerworld.com/zh/models/39368#profileId-38480</a>&nbsp;I am really glad that there are many guys like this collapsible katana, and I do appreciate your suggestions and opinions.&nbsp;So I found some time and made a new one, addressing the following issues in the old one.<ol><li>The strength of the handle-guard connector. This time I combined the handle and connector together to enforce the strength.</li><li>The decoration on the handle is better to be multi colorred. So I made a new structure with the outer shell and inner shell to form the handle. With different colors of the shell, the handle now looks more real.</li><li>The blade guide is thicken so should not be easy to break now.</li><li>the disassemble structure are located at the tail now. And now only two pieces of filament could lock it.</li></ol>&nbsp;Some important suggestion and notes<ol><li>When printing the slide lock, I suggest to use the Cool/Smooth Plate. As when using Textured Plate, the thickness of slider sole is a little bit thicker than it should be, it might cause hard to slide.</li><li>Still need to use a little bit instant glue for the handle and guard, do not apply too much as it might glue the slider too. Don&#39;s ask why I know it :)</li><li>The holes to lock the tail and handle are printed without any support, so it might not be perfect. This might cause the filament hard to insert. I suggest to use a Hex Key 1.5 to clear the holes first.</li><li>The folding diameter of the rubber ring is 60 mm.</li><li>This time, the handle is printed with Support, and I have tuned it many times to perfect the rhombic holes. BUT it is still not perfect.</li></ol>If some one has better ideas, please let me know, or update your configuration here.

材料

测试

工具

家居

玩具