SheepdogForge

____________________________________________________________________________________________________________________ ☀️ If you want to sell prints of this model, as well as all of my models, future and past, <a target="_blank" href="https://patreon.com/ChromaC3D?utm_medium=unknown&amp;utm_source=join_link&amp;utm_campaign=creatorshare_creator&amp;utm_content=copyLink" rel="nofollow noopener">become a member of my Patreon for a commercial license!</a> ☀️ ____________________________________________________________________________________________________________________&nbsp;A beautiful set of bookmars with a different pictures of a red blossom The full set is to be printer together. It&#39;s designed in such a way which makes this possible with the color changes. Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm For folks without AMS: Filaments Used: PLA <a target="_blank" href="https://kingroon.com/collections/3d-printer-pla-filament?sca_ref=6268797.MtX4KIZPrO" rel="nofollow noopener">Kingroon Black</a> Transmission Distance: 0.4 PLA <a target="_blank" href="https://kingroon.com/collections/3d-printer-pla-filament?sca_ref=6268797.MtX4KIZPrO" rel="nofollow noopener">KINGROON WHITE</a> Transmission Distance: 5.5 PLA <a target="_blank" href="https://kingroon.com/collections/3d-printer-pla-filament?sca_ref=6268797.MtX4KIZPrO" rel="nofollow noopener">KINGROON Red</a> Transmission Distance: 4  Swap Instructions:     Start with Black     At layer #7 (0.64mm) swap to WHITE     At layer #14 (1.2mm) swap to Red for the rest. If you like my work, drop me a follow!🤜🤛&nbsp;&nbsp;

"Red Blossom" - Bookmarks Set

book

MakeCents 3dp

Phase 10 box remixed from the UNO box, that you can print in place without hardware. Same box as my print in place UNO box, remixed from the same UNO box.&nbsp;<ul><li>Phase 1: 2 sets of 3</li><li>Phase 2: 1 set of 3 + 1 run of 4</li><li>Phase 3: 1 set of 4 + 1 run of 4</li><li>Phase 4: 1 run of 7</li><li>Phase 5: 1 run of 8</li><li>Phase 6: 1 run of 9</li><li>Phase 7: 2 sets of 4</li><li>Phase 8: 7 cards of one color</li><li>Phase 9: 1 set of 5 + 1 set of 2</li><li>Phase 10: 1 set of 5 + 1 set of 3</li></ul>

Phase 10 box print in place

games

dtngx

<h3>Model Info</h3> This model was created using photogrammetry. Around 80 Photos of a real horse skull were taken with an iPhone 12 Pro Max main camera lens and a turning table and then combined into the 3D model using the “Object Capture” command line tool by Apple. The result on the outside and any more “open” parts of the skull is amazing, but it lacks a bit of detail in the inside of the skull where pictures could not be taken from every angle. The model was not edited besides removing the turning table from it.&nbsp;<h3>The Print</h3>The shown print was done using an A1 mini. It worked very well but the print profile can be improved for better results.The following parameters were used but not ideal:<ul><li>Bambu Textured PEI Plate</li><li>Bambu 0.2mm stainless steel nozzle</li><li>0.10mm Standard profile</li><li>variable layer height activated</li><li>Arachne wall generator</li><li>4 walls, thin wall mode</li><li>10% grid infill</li><li>auto tree supports (nor recommended) </li><li>only support critical areas activated </li><li>outer brim 5mm</li></ul>I am still working on a good print profile. The print worked, but some parts did not turn out very well and a some cleanup was needed with tweezers. definetly a challenge to optimize this one.&nbsp;Our findings and possible improvements so far:<ul><li>The overhanging area between front and back teeth definetly needs a support, otherwise it can easily fail.</li><li>The supports need “support wall loops” set to a higher number. The shown print was done with 0 but one support broke off and another one sagged visibly. </li></ul>&nbsp;

Horse Skull 3D Scan Fury

horse

Willi 3D

Create a pit droid …. or more! (They work better in groups.)&nbsp;If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work bye me a coffee.</a> Thanks!&nbsp;Description:This is a KIT CARD of a pit droid. Scale 1:10&nbsp;Update:(24/08/23) <ul><li>optimized printability of the pelvis</li></ul>(18/08/23) <ul><li>optimized upper leg to pelvis fit</li></ul>Printing:Layer height: 0.1Supports: NoBrim: NoMaterial: PETG, (ABS), (PLA)&nbsp;Assembly: The connections are designed and optimized for PETG, the use of PLA or ABS makes assembly more difficult and the parts can break. Follow the instructions in the picture.

book

games

horse

Star wars cool crap