Sandersann

YDesign

<h3>HSW Ratchet Mounts for 1/2, 3/8 and 1/4 Inch drive</h3>This design comes with three models designed to fit a 1/2, 3/8 and1/4 Ratchet. The mounts fit directly into the HSW system without any adapters. Each mount has notch so the racchet will lock in place and stay secure. To release the ratchet press the button on the end of the ratchet, the same as releasing a socket.&nbsp;<h4>Print Settings:</h4>These mounts can be printed in either PLA or PETG. No supports are needed.<ul><li>Material: PLA/PETG</li><li>Layer height: 0.2mm</li><li>Perimeters/Wall Loops: 4</li><li>Sparse Infill Density: 20%</li></ul>

HSW Ratchet Mounts for 1/2, 3/8 and 1/4 Inch drive

HSW (Honeycomb wall storage)

dakjones82

<h2>3D MODEL DESCRIPTION</h2>Track map wall art for racing enthusiasts! Models range from 180 -250mm wide but can be scaled or broken up for your needs. Use wall-safe double-sided tape for wall adhesion with mess/damage-free removal.<h2>3D PRINTING SETTINGS</h2>.20 layer height 15-20% infill 2-3 walls Pause for filament change at nameplate start Iron top layer only for a clean smooth finish

Circuit De Catalunya Map (Multi Color with Nameplate)

Race Tracks

Disegni Fugazi

I found the 5&#34; displays a little too small for my taste and wanted to go with the 6.8&#34; display. I didn&#39;t find too many existing models for this so decided to design my own taking inspiration from what was out there. My goal was to make a very high quality model with ease of printing/assembly in mind. In its current state you&#39;ll have 2 USB outputs for this DDU. In the future I&#39;d like to create a custom PCB to get that down to a single USB output (please contact me if you&#39;d like to help with that development as it&#39;s a bit outside my wheelhouse).The mounting bracket is designed for a Simagic Alpha Mini. I can make new brackets for other wheelbases if you send me dimensions. The bracket is designed to allow you to slide the display very low as I wanted it just above the steering shaft but you can slide it up high as well if that fits your needs.The display and LEDs can be controlled by <a target="_blank" href="https://www.simhubdash.com/" rel="nofollow noopener">SimHub</a> or similar software. I highly recommend the <a target="_blank" href="https://discord.gg/jReXXVWFmp" rel="nofollow noopener">Lovely Dashboard</a> and <a target="_blank" href="https://discord.gg/SxjGvR3K2W" rel="nofollow noopener">Daniel Newman Racing LED Profiles</a> (no 5-20-5 profiles at the time of this writing but he said he&#39;ll be making one in time). Please support these projects if you find their work helpful (I have no doubt you will!).Bill of Materials:<ul><li><a target="_blank" href="https://www.aliexpress.com/item/3256802340684101.html?spm=a2g0o.order_list.order_list_main.50.48181802JEF9EM" rel="nofollow noopener">M3 x D4.2 x L6.0 Thread Inserts</a> (11)</li><li><a target="_blank" href="https://www.aliexpress.com/item/3256802919609113.html?spm=a2g0o.order_detail.order_detail_item.31.15ecf19cKHIbGP" rel="nofollow noopener">M3 x 8mm Countersunk Head Screws</a> (4 - Enclosure)</li><li><a target="_blank" href="https://www.aliexpress.com/item/2261799962114486.html?spm=a2g0o.order_detail.order_detail_item.5.408bf19cPnLH6k" rel="nofollow noopener">M3 x 8mm Button Head Screws</a> (3 - Arduino Mount)</li><li><a target="_blank" href="https://www.aliexpress.com/item/3256804607696173.html?spm=a2g0o.order_detail.order_detail_item.5.2449f19c1SwIm7" rel="nofollow noopener">M3 x 8mm Thumb Screws</a> (4 - DDU Mount)</li><li><a target="_blank" href="https://vocore.io/" rel="nofollow noopener">VoCore 6.8&#34; Display</a></li><li><a target="_blank" href="https://www.aliexpress.com/item/2251832476876176.html?spm=a2g0o.order_list.order_list_main.62.48181802JEF9EM" rel="nofollow noopener">Arduino Nano</a></li><li><a target="_blank" href="https://www.aliexpress.com/item/2251832495700653.html?spm=a2g0o.order_list.order_list_main.68.48181802JEF9EM" rel="nofollow noopener">WS2812B Individually Addressable Led Strip</a> (1m 144 IP30)</li><li><a target="_blank" href="https://www.aliexpress.com/item/2251832854093842.html?spm=a2g0o.order_list.order_list_main.38.48181802JEF9EM" rel="nofollow noopener">Micro USB Cable</a></li><li><a target="_blank" href="https://www.aliexpress.com/item/3256803462346535.html?spm=a2g0o.order_list.order_list_main.44.48181802JEF9EM" rel="nofollow noopener">Mini USB Cable</a></li><li><a target="_blank" href="https://www.aliexpress.com/item/2251832829997304.html?spm=a2g0o.order_list.order_list_main.178.48181802JEF9EM" rel="nofollow noopener">24 AWG Wire</a></li><li>3M Double Sided Tape</li><li><a target="_blank" href="https://www.aliexpress.com/item/3256806146321415.html?spm=a2g0o.order_list.order_list_main.20.48181802UKpfj9" rel="nofollow noopener">Faux Carbon Fiber Build Plate</a> (optional)</li><li>M8 x 12mm button head screws (2 - may be different for your wheelbase)</li></ul>Printing:Optional: I used the faux carbon fiber plate to give that look to the front and back of the enclosure.Material: PLA or better for housing, TPU for display gasket (optional)Layer height: 0.2mmWall loops: 4Top shell layers: 4Bottom shell layers: 4Infill: 60%Infill pattern: GyroidSupports: only needed for the countersunk holes on the mounting bracket and wire passthroughs on the side of the front enclosure<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_6d048874f4edb.png"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_d1dc3629b2b5b.png">&nbsp;Assembly:<ol><li>Melt the threaded inserts (11) into back enclosure using a soldering iron<ol><li>Set temperature to melting temperature of material used</li><li>Make sure inserts are flush with outer surface<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/05318f49-f2ea-4463-a65e-caaedb4e5ec7.jpeg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/33718196-d00c-43d9-a3d6-9bd69de35537.jpeg"></li></ol></li><li>Cut LED strip into 3 sections (Tip: these LEDs are very close together and can make soldering the center connection difficult. You can sacrifice an LED when cutting and leave a larger portion of the connection to solder onto to make things easier. It&#39;s doable without doing this though.)<ol><li>2 x 5 LED strips</li><li>1 x 20 LED strip</li></ol></li><li>Solder the LED strips together using 24 AWG wire<ol><li>~36mm for outer wires</li><li>~33mm for middle wires</li><li>~30mm for inner wires</li><li>Make sure the arrow on the PCBs are all pointing the correct direction (away from Arduino)</li></ol></li><li>Solder Arduino Nano to LED strip<ol><li>~60mm wires</li><li>Solder directly to the Arduino, no pins needed (there are cutouts on the Arduino mount to allow the wires to poke through the back)</li><li>Use VIN (red wire), GND (blue wire), and D6 (white wire)</li></ol></li><li>Remove adhesive backing from LED strips and place them on the platforms<ol><li>Start with the 20 LED strip</li><li>Notice that there is an alignment arrow on each platform for the center point of the strip</li><li>Start at the center and slowly work your way out</li><li>Once perfectly aligned, repeat the process for each 5 LED strip</li></ol></li><li>Screw down Arduino cover using button head M3 x 8mm screws<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_05533bf36d175.jpeg"></li><li>Test fit the front enclosure to make sure LEDs are aligned with holes, adjust as needed then remove front of enclosure (be careful sliding over the Arduino USB port)</li><li>Use double sided tape to attach the ribbon cable seat to the back of the VoCore display then use another piece of tape to attach the ribbon cable to the seat as shown in the picture<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_b51857572cd7f.jpeg"></li><li>Thread the USB cable for the VoCore display through the right port on the front enclosure and press it into the cable clamp to prevent accidental pulling of cable<ol><li>Leave about 140mm of cable to plug into the display<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_cf002ee4034fb.jpeg"></li></ol></li><li>Carefully plug in the display and rest it onto the mounts (ensure wires are out of the way and not being pinched/pulled)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_54e6c0c6dc952.jpeg"></li><li>Optional: glue the TPU gasket to the inner face of the front enclosure (I didn&#39;t end up using this and everything seems to stay in place nicely)</li><li>Carefully slide the front enclosure over the back enclosure and secure using M3 x 8mm countersunk screws (4)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_d7fc626b1c6ff.jpeg"></li><li>Attach mounting bracket using 4 M3 x 8mm thumb screws (don&#39;t quite fully tighten these yet so that you can fine tune the positioning once it&#39;s mounted to the wheelbase)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_310b23f6a8be.jpeg"></li><li>Attach the mounting bracket to the wheelbase using M8 x 12mm button head screws (may be different for your wheelbase)</li><li>Position DDU at desired height and tighten thumb screws</li></ol>SimHub Setup:The display should be recognized right away by Simhub. You can simply navigate to the device tab and load the dashboard of your choice and adjust the display to your liking. Again, I highly recommend the <a target="_blank" href="https://discord.gg/jReXXVWFmp" rel="nofollow noopener">Lovely Dashboard</a>. Note that you&#39;ll need to flip the display.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_aa7841a5ed0d4.png"></figure>For the LEDs, you&#39;ll need to flash the Arduino using the provided tool:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_07dd677a2587f.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000159494/design/2024-05-04_98d3d7b99cd62.png"></figure>Make sure you select the correct COM before flashing. If you don&#39;t see your COM listed you likely need to <a target="_blank" href="https://ftdichip.com/drivers/" rel="nofollow noopener">install the drivers</a>.After it&#39;s flashed, you&#39;ll need to configure the LED profile to your desired behavior on the RGB LEDs tab. This is fairly straightforward but you can definitely get very detailed in your configuration. Definitely check out <a target="_blank" href="https://discord.gg/SxjGvR3K2W" rel="nofollow noopener">Daniel Newman Racing LED Profiles</a> to see how crazy/awesome this can get.Have fun and I welcome feedback!&nbsp;Edit 1: Added alternate faceplate with rectangular LED openings instead of round.

Simracing VoCore 6.8" DDU

Sim Racing Prime

select2start Print

2x2x5 Bin | Lable | Gridfinity | Deskorganizer | Tool | select2stertPrint

Gridfinity

vitaprint 3D

This is a perfect Box for your Bambu Lab Spare Parts. I made all Bambu Lab printer Models to a Lid Design.You need foloowing Screws to complete it:&nbsp;<ul><li>M3 x 30 = 4 pcs (for the Hinges)</li><li>M3 x 35/40 = 2 pcs (for the Handle)</li></ul>&nbsp;Big Box:230 x 210 x 70<a target="_blank" href="https://makerworld.com/en/models/105260" rel="nofollow noopener">https://makerworld.com/en/models/105260</a>230 x 210 x 140<a target="_blank" href="https://makerworld.com/en/models/92348" rel="nofollow noopener">https://makerworld.com/en/models/92348</a>&nbsp;Small Box:175 x 130 x 110:<a target="_blank" href="https://makerworld.com/de/models/97173" rel="nofollow noopener">https://makerworld.com/de/models/97173</a>175 x 130 x 70:<a target="_blank" href="https://makerworld.com/de/models/408354" rel="nofollow noopener">https://makerworld.com/de/models/408354</a>

Bambu Lab Box XL X1C / P1P / P1S / A1 / A1 Mini

Naomi

Bamingo Design

Keep your Xbox One controller within reach with this easy-to-print desktop stand.

Xbox Controller Desktop Stand with Logos

House Prime

Fatalchaos25

valentines love sign. not much to say about it but happy printing

valentines love ornament

Clinic

andythilo

NOTE 23-01-24 - Motor Case V1.1 in Raw files section with added hole relief for gearbox screw head.&nbsp;NOTE - V1.1 Profile released - I'd missed an important support from plate 3 - Apologies&nbsp;As soon as I saw the V-Spooler by @Fryby Additive, I knew I wanted to motor mod it. Over the last week or so, Tim (Fryby) and myself have been chatting and exchanging ideas and my dual motor mod is the culmination of many hours of prototyping and testing.&nbsp;My goal was to keep the model simple, aesthetically pleasing but mostly reliable and powerful enough. My dual motor mod requires a couple of reprints, namely the outer gear frame and the input shaft as well as some extended feet to stop it tipping over and some upgraded spool holders specifically sized for the Bambu re-usable spools.&nbsp;Input shaft, feet and spool holders remixed with permission from owner @Fryby Additive&nbsp;Full Instructions in attached PDF&nbsp;Test re-spool video here -<figure class="media"><div data-oembed-url="https://youtu.be/lu6Is-TscMw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/lu6Is-TscMw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;Hardware needed, Amazon US and UK links below :-&nbsp;2 x 12VDC Greartisan JSX40-370 DC 250RPM Worm Geared Motors - <a target="_blank" href="https://a.co/d/aJZPaNc" rel="nofollow noopener">https://a.co/d/aJZPaNc</a> / <a target="_blank" href="https://amzn.eu/d/fnuTj81" rel="nofollow noopener">https://amzn.eu/d/fnuTj81</a>2 x 30 Tooth 0.8 Mod Spur Gear for 6mm Shaft - <a target="_blank" href="https://a.co/d/hDCySu0" rel="nofollow noopener">https://a.co/d/hDCySu0</a> / <a target="_blank" href="https://amzn.eu/d/iKv4UhI" rel="nofollow noopener">https://amzn.eu/d/iKv4UhI</a>1 x 12VDC 80W DC Motor Reversible Motor Controller - <a target="_blank" href="https://a.co/d/fsq2sqQ" rel="nofollow noopener">https://a.co/d/fsq2sqQ</a> / <a target="_blank" href="https://amzn.eu/d/5er8v3b" rel="nofollow noopener">https://amzn.eu/d/5er8v3b</a>1 x 5.5 x 2.1mm DC Power Socket - <a target="_blank" href="https://a.co/d/42z1OLm" rel="nofollow noopener">https://a.co/d/42z1OLm</a> / <a target="_blank" href="https://amzn.eu/d/2DIvEb8" rel="nofollow noopener">https://amzn.eu/d/2DIvEb8</a>1 x 40mm x 10mm 12VDC Fan - <a target="_blank" href="https://a.co/d/aKu3ic7" rel="nofollow noopener">https://a.co/d/aKu3ic7</a> / <a target="_blank" href="https://amzn.eu/d/88UPW3l" rel="nofollow noopener">https://amzn.eu/d/88UPW3l</a>1 x 40mm x 40mm Fan Grill - <a target="_blank" href="https://a.co/d/53ub1UQ" rel="nofollow noopener">https://a.co/d/53ub1UQ</a> / <a target="_blank" href="https://amzn.eu/d/3cIC2Co" rel="nofollow noopener">https://amzn.eu/d/3cIC2Co</a>12 x 3mm Heat-set Inserts - <a target="_blank" href="https://amzn.eu/d/aoujVTM" rel="nofollow noopener">https://amzn.eu/d/aoujVTM</a>9 x M3 Cap Head 8mm Screws9 x M3 Washers4 x M3 Cap Head 20mm Screws4 x M3 Cap Head 25mm Screws&nbsp;NOTE - <ol><li>Lid with trim colour profile added</li><li>Motor Spur Gears added if you want to save money but you will need M5 grub screws</li><li>Bambu specific sized spool holders are included to provide better centreing. </li></ol>&nbsp;Full Instructions in attached PDF&nbsp;

V-Spooler Dual Motor Mod

3D Printer Prime

Alexis_

<h2>Present Box - Christmas New Year Gift Box</h2><h3>Print in place Gift Box</h3>&nbsp;Description: The Christmas Gift Box - Festive Delight is a meticulously designed 3D file that allows you to create a stunning and festive gift box for the holiday season. With its intricate details and easy-to-print structure, this 3D file is perfect for DIY enthusiasts and 3D printing enthusiasts alike.&nbsp;Features: 1. Easy to Print: The file is optimized for easy printing, ensuring a smooth and hassle-free printing experience. 2. Festive Design: The gift box features a charming and intricate design, capturing the essence of the holiday season. 3. Customizable: The file allows for customization, enabling you to adjust the size and scale of the gift box to suit your preferences. 4. Print Quality: The file is designed to produce high-quality prints with fine details and clean lines.&nbsp;<figure class="media"><div data-oembed-url="https://vimeo.com/891858542?share=copy"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://player.vimeo.com/video/891858542" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allowfullscreen=""></iframe></div></div></figure>&nbsp;&nbsp;You can personalize it easily with the text function in bambu studio :&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/249231/2023-12-06_045b63a75a6da.png"></figure>&nbsp;&nbsp;<h4>Print Settings</h4><ul><li>basic setting on bambu studio</li></ul>&nbsp;&nbsp;Enjoy !