STACK3D DESIGNS

blecheimer

Thirsty, wastelander? Here, have a Nuka-Cola, fresh from before the war. What it costs, you ask? Nothin&#39;, this is on me. But if if you can spare a &#34;boost&#34; I will be as happy as a puppy with two tails. ;)&nbsp;Print your own Nuka-Cola bottle from Fallout in the great 2077 Space Age design! I designed it from the scratch according to some photos of an original bottle. The bottle is hollow and matches <a target="_blank" href="https://makerworld.com/en/models/436309" rel="nofollow noopener">my Nuka-Cola Bottle Cap</a>. You can easily press the cap on the bottle. Without the cap the bottle has a height of 178mm and can hold a volume of 380ml. I also added an optional label for the bottle that can be glue to one side. On the other side there is an embossed Nuka-Cola logo.Ready for an upgrade? <a target="_blank" href="https://makerworld.com/en/models/446415" rel="nofollow noopener">See my Nuka-Cola Quantum bottle.</a>&nbsp;Print preparation: Make sure that your print bed is clean and grease-free. An unsufficient bed adhesion is in most cases not a problem of the print profile but a cleanliness issue. If you want you can use glue on your print bed but for PLA this should not be necessary. Use the textured PEI plate and a bed temperature of 55-60°C. For the print quality it is important that you use a good and calibrated filament. Know your k-factor and use the correct flow setting. Bambu filament makes this step easier but any other quality brand will do the job.&nbsp;Print settings for the bottle: The bottle is an easy print. Use a 0.4mm nozzle, set the slicer to the 0.28 Extra Draft slicing profile and activate the spiral vase mode. The outer line thickness should be 0.8mm. Now you will get a robust, but hollow bottle. I like to reduce the outer wall speed a little bit to further improve quality. Be warned - the bottle is not meant to be waterproof. You can try to use concentric pattern and ironing for all surfaces. But if you really want a leak-free bottle you need to use clear coat or expoy on the inside to seal all pores.&nbsp;Print settings for the optional label: The optional label will take a long time to print. It is divided into two parts to make printing easier. An AMS is necessary because you need two colours. Use the 0.08mm Extra Fine slicing profile but change the layer height to 0.1mm. Set the wall generator to &#34;Arachne&#34; and reduce the outer wall speed to 100 mm/s. A small print tower will help to enhance the colour separation. After printing glue both halves to the empty frame on the bottle. I added the complete label to the raw model files if you want to try your own print settings.&nbsp;For more detailed print settings take a look at my print profiles. The print profiles can be used with A1, P1 and X1 printers.&nbsp;UPDATE 2024-04-22: User dplivingston proposed to print the label flat and use a heat gun to mold the label into the correct shape. I added a flat-label-STL to the download section if you want to try it.UPDATE 2024-04-24: User 3dlyx tried out the flat label (+ shape it with heat) and noticed that it is not wide enough. I modified the flat label so that it should now better fill-out the frame on the bottle. I guess, it is still not perfect…&nbsp;Nuka-Cola - containing 120% of the recommended daily allowance of sugar&nbsp;If you want to support me you can leave a tip at <a target="_blank" href="https://ko-fi.com/blecheimer" rel="nofollow noopener">ko-fi.com/blecheimer</a>.&nbsp;&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="https://creativecommons.org/licenses/by-nc-nd/4.0/" rel="nofollow noopener">CC-BY-NC-ND 4.0</a>. The shown model is fanart and must not be used commercially. Copying this model to other 3D printing websites is not allowed without my permission.

Nuka-Cola Bottle (from Fallout)

to print

220°c

Giant NES Cartridge. This is made to be hung on a wall, there is a wall hook on the back. You can look for the images online by googling NES Labels. I used MECOLOUR Holographic Sticker Paper, you can find it on Amazon. I resized the images in word. If you do not resize the model and just use the 3mf I uploaded, the sticker size should be around 7.7H X 3.93W. You may have to cut a little off the top and bottom depending on where you find your images.&nbsp;I printed these upsized down using a Gyroid pattern and 5% infill to save on time. I found that 0.16 layer height works best to hind the lines. The supports I used were normal snug with a 25% threshold angle.&nbsp;These were printed with Overture Matte light gray.&nbsp;Happy Printing!

Giant NES Cartridge Wall Art

lego

Simple Solutions 3D

For more branded caliper covers:They have been moved to individual models. To find the caliper cover you&#39;d like, please checkout my profile for a easy to search selection.&nbsp;Every car guy (or girl) needs a set of these to show off their brand of choice!&nbsp;Brake Caliper coasters that are sure to complete the look of any garage, living room, or anywhere you put them.&nbsp;Print in any colour you wish and simply glue on the desired nameplate. Blank nameplate also included to make your own such as your name or another brand of choice.&nbsp;You do not have the right to sell this file or any prints of it. You do not have the right to distribute the files. If you wish to share, please provide the link to this page.&nbsp;To purchase commercial right, check out my Cults3D listing <a target="_blank" href="https://cults3d.com/en/3d-model/home/disc-brake-coaster" rel="nofollow noopener">https://cults3d.com/en/3d-model/home/disc-brake-coaster</a>

Disc Brake Coaster Set

coasters

lantern

3DprinterTips

This 3D-printed baby dragon is like a magical toy. It's been carefully designed to look super cool, and you can move its arms and legs to make it do all sorts of fun poses. This dragon doesn't have wings, which makes it unique. Whether you're into make-believe adventures or just want a cool decoration, this baby dragon is perfect. It's a mix of technology and art, and it's a real eye-catcher wherever you put it!

Articulated Baby Dragon

articulating

bambu tools

Rogi Studios

Every month a Skull will be released with different types of hair, beard and accessories such as cigars, glasses, cap and more, I think it will be very interesting because I have never seen anything like it and it will be cool to print them in color because it will give a great ask. This collection will be a bonus and the next models will be EXCLUSIVE FOR PATRONS. So if you found it interesting join us on Patreon and don't miss any. <a target="_blank" href="https://www.patreon.com/rogistudios" rel="nofollow noopener">patreon.com/rogistudios</a>DOES NOT REQUIRE SUPPORTS