RufusRed

Lazy_Mardeux

I made a desiccant tray that snaps with the original desiccant cover for the Bambu Lab AMS.&nbsp;I simply used PLA and .2mm standard settings for printing.&nbsp;This should fit just perfect in your ams if it&#39;s the same as me. I bought it early 2024.To install the original cover on the desiccant tray, start by joining the part closest to you by first lining up the pimples with the holes on the cover, and then snap it with the tab on the back.The tray is placed in the AMS just like the cover alone would be placed; inserting the 2 front tabs in place, and snapping the back tab in place.&nbsp;NoteThe original cover holds most desiccant beads, BUT, smaller beads can get through the holes, so don&#39;t overfill and turn upside down.&nbsp;&nbsp;

BambuLab AMS Desiccant Tray w/ OEM lid

Bambu

chippwalters

Use my print profile for best results, I cannot guarantee print profiles by others.&nbsp;Japanese flower vase with intricate detail uses 2 colors for printing. Only 2 filament swaps with no purge block. Small vase only uses 123g of filament but takes 8 hours to print due to the incredible detail of the surface.Black color is in slot 4 with green color in slot 2 (A1 mini) and the changes are at layers 58 and 402.<ul><li>Start with black</li><li>Change to green at 58</li><li>Change back to black at 402</li></ul>Tested watertight with PLA.&nbsp;&nbsp;

Hana Whisper flower vase

Garden

cl@ytr0n

Simply hold the Snap-Fly between your fingers like you&#39;re about to snap then… snap and fly! ✈ If you&#39;re left handed, hold the Snap-Fly upside-down and watch it defy gravity!&nbsp;The small “mouse-ears” are just for better bed adhesion and can be clipped off after printing. Or just leave them on! It will still fly!There&#39;s no reason to not print this super quick and fun toy! You will want to make these for your friends and family!&nbsp;I hope you found this print fun and please post your makes!&nbsp;Printed in PLA - Silk is not recommended but possibleLayer Height: 0.2mmPerimeters: 3Infill: Doesn&#39;t MatterSupports: NahBrim: NahOther Hardware: Working Phalanges &nbsp;Side Note: Other users have also noticed that printing multiple of these on one bed works as a great stringing test!&nbsp;Oh! Also! Don&#39;t waste your time with the imitators who don&#39;t give attributions. This Original Snap-Fly flies the best! <a target="_blank" href="https://makerworld.com/en/models/488897#profileId-401949" rel="nofollow noopener">“FlickFlier”</a>

SNAP-FLY! |  The ORIGINAL Mini Flying Toy

Josh-3D

A tea bag dispenser in two sizes with lid! Pretty simple model, but wanted something a little more stylish than what I was finding otherwise. I hope you enjoy it too! &nbsp;Hardware Requirements:2 x M3 screws (About 10mm or longer)&nbsp;Assembly:Screw the lid on! You can keep the screws a little loose, for an easy swing lid, or you can tighten them a little so the lid stays in place as you open it. &nbsp;-------If you like my work, consider showing your love by <a target="_blank" href="https://www.buymeacoffee.com/josh3d" rel="nofollow noopener">Buying me a coffee</a>. Additionally, if you&#39;re looking to sell prints of my design, please check out my <a target="_blank" href="https://www.patreon.com/josh3d/" rel="nofollow noopener">Patreon</a> page for more information. on.

Tea Bag Dispenser

Container

squinn

A portable cable organizer which is setup as an easy print-in-place and includes a knob on the side for conveniently winding up the cable when you're ready to pack it away.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_fd01d80e216de.gif"></figure>This model is an easy print that requires no supports, and three different sizes are provided to accommodate cables of different lengths. If you're not sure which to choose, I'd recommend starting with the “medium” size.&nbsp;After printing, you'll want to place the cable within the groove at its halfway point, close the lid (which is intentionally designed to close tightly), wind up the cord clockwise using the handle, and then extend by simply grabbing the cable by both ends.&nbsp;Update 2023-09-13:&nbsp;Alternative smooth-sided versions of all three sizes have now been added, and also the handle design was slightly adjusted to add a small fillet and chamfer to decrease the bridge distance. Here's a close-up picture of the updated handle on the knurled and smooth-sided versions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_e75ea621224d08.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_68f2b35a6774b8.jpg"></figure>&nbsp;

Portable Cable Organizer / Winder

Tool

Onkelsam

the well-known torture taoster from clockspring with a double dovetail test.&nbsp;The dovetail test has a tolerance of 0.1mm.  Dovetail should be able to be pressed into the desired position with firm pressure.&nbsp;The 0.2mm height standard settings were used for slicing.&nbsp;Cold plate with glue works perfect for me.&nbsp;&nbsp;IMPORTANT: The print does not have to be perfect or beautiful. It is there to show what your printer can do and where improvements may need to be made (print adhesion / cooling / material ... etc.)

Torture Toaster with double Dovetail Test

Test

StefanV

The original version works with the Watch Ultra, but fast charging is not always active because of the off-centred position. This remix has the watch fast charger moved up by 2.6mm, allowing the Apple Watch Ultra to be centered and to activate fast charging.

Bambu

Garden

Toy

Container

Tool

Test

Stand

Dispencer