Kowalski

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014267/design/2023-09-19_1c59e405d0a79.png"></figure>This is a V-twin engine model that consists of various parts like a crankshaft, connecting rods, camshafts, gears, and a throttle valve, among others. It can replicate the functioning of a real engine. The engine model has magnetic decorative covers and hollowed-out structures that make it easy to observe the internal parts. It can be rotated using either a manual crank or an electric motor. In manual mode, the engine runs at a slow pace, allowing for a better observation of each movement. With the motor drive mode, the engine can run continuously by using the motor to rotate the crankshaft.&nbsp;Recommended filaments: Bambu PLA series, PLA Basic is recomended especially in moving parts<a target="_blank" href="https://store.bambulab.com/products/pla-basic-filament?variant=40820833517683" rel="nofollow noopener">https://store.bambulab.com/products/pla-basic-filament</a>Hardware Kit: Engine Model Components Kit-005<a target="_blank" href="http://store.bambulab.com/products/engine-model-components-kit-005" rel="nofollow noopener">http://store.bambulab.com/products/engine-model-components-kit-005</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the video tutorial step by step to print and assemble your build. <figure class="media"><div data-oembed-url="https://youtu.be/wv3qnfMbuko"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/wv3qnfMbuko" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Engine Model 005

Engineering examples

Pathfinder.Ant

多功能机械臂（Multifunctional Robotic Arm）：1.此次模型为桌面台灯，适用于办公桌，书桌以及当作摆件或者氛围灯（This model is a desktop desk lamp, suitable for office desks, desks, and as a decorative or ambient light.）；2.模型直径约10cm左右，延伸高度约30cm，不包括扩展灯罩部分（The model has a diameter of about 10cm and an extension height of about 30cm, excluding the extended lampshade.）;3.模型适配拓竹的夜灯套件（Model adapted night light kit for LED Lamp Kit 001）;4.涉及多种尺寸螺丝，包括M2，M3，M4，尽量使用内六角螺丝，视觉观感会更好（Involving multiple sizes of screws, including M2, M3, M4）;5.小风扇专篇详见（For detailed information on the small fan section, please refer to）：<a target="_blank" href="https://makerworld.com/zh/models/485133#profileId-397570" rel="nofollow noopener">https://makerworld.com/zh/models/485133#profileId-397570</a>

Multifunctional Robotic Arm - Desktop Lamp Edition

Light Kit stuff

BrandedAbstract3D

I just wanted to drop you a quick note of thanks and share a link to the creator that inspired this phone holder. The incredible <a target="_blank" href="https://makerworld.com/en/@StepanK" rel="nofollow noopener">@StepanK</a> here on Maker World. Your original creation sparked some creativity on my end, and I ended up doing a simple remix of it. Go checkout all of his new Maker World creations. His work has been a fantastic source of inspiration, and I&#39;m happy to honour that by sharing what I&#39;ve come up with. Thanks again for sharing your creativity with the world.&nbsp;Wanna Sell This and Other Items? Check out my Patreon for a commercial license. <a href="patreon.com/BrandedAbstract3D" rel="nofollow">patreon.com/BrandedAbstract3D</a>&nbsp;Phone holder designed to resemble a Recaro Racing Seat, unique and functional, great for any space. It&#39;s a top conversation starter for anyone who loves cars. Always adds a touch of car scene to your surroundings.&nbsp;To complete the phone holder you&#39;ll need:<ul><li>1 x Seat (printable)</li><li>1 x Roll Cage (printable)</li><li>2 x Support Struts (printable)</li><li>8 x M3 Screws</li></ul><h3>Print Settings</h3>I usually go for the BBL “Standard” 0.20mm settings. It seems to strike the right balance between quality and speed compared to other profiles. I&#39;m a fan of the consistent layer height of 0.2mm, but variable layer height is good too! Feel free to play around with the print quality settings to see what works best for you. I&#39;ve had success with BBL Filaments and various other brands, but for Silk PLA, slowing down the outer walls to around 50mm/s seems best.&nbsp;<ul><li>Seat: Use a 10% grid infill—it&#39;s sturdy enough to hold a phone. I used to two bottom shell layers; once the support struts are fitted, the seat base doesn’t touch the tabletop. And, I set the seam position to “back”. I’ve found it looks more intentional, and you kind of forget it’s there!</li><li>Roll Cage: A 0% infill will save print time and is still pretty strong, even for two perimeters.</li><li>Support Struts: Use a 15% grid infill. This part is mostly top and bottom shell layers, but a good scaffold is needed for the top layers to build on. Important: set the top surface to 50mm/s for a smoother finish! You could turn on ironing, but I prefer seeing some industrial layer lines.</li></ul><h3>Assembly</h3>Assembly is a breeze! You&#39;ll get it from just looking at the photos. Insert the M3 screws into the holes and tighten all parts together. Avoid screws longer than 10mm to prevent them from sticking out of the holes in the roll cage. It won’t break anything, but you’ll see the backs of them protruding.&nbsp;Happy Printing!&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/ba3d" rel="nofollow noopener">Buy Me A Coffee</a> ☕(Appreciated but absolutely not required)

Recaro Racing Seat Phone Holder

Phone Stands

adiskovarik

Blank key tag with customizable name.Easily add text directly in your slicer. Text height is 1mm.&nbsp;Easy dual color printing with only one filament swap.For dual color swap filament at 2mm.Recommended layer height is 0.2mm for easy color swap.

Keytag/Keychain with custom name

NameTags

sharpie00

<h3>3D Printable Console Placards - Volume 2</h3>Continue to celebrate your love for retro gaming with Volume 2 of my 3D printable console placards collection! Building on the success of Volume 1, this new set features even more iconic video game brands and consoles, perfect for adding to your growing display.&nbsp;<h4>Specifications:</h4><ul><li>Dimensions: 9.76 inches (L) x 3.03 inches (W) x 0.79 inches (H)</li><li>Colors: Each placard has been meticulously colored in Bambu Studio and is ready for immediate printing.</li><li>Material: Designed using official Bambu Lab PLA filament, though any filament brand can be used.</li></ul><h4>Mounting:</h4>Mount these placards effortlessly on your wall with the smallest size of 3M Command Strips for a clean and hassle-free setup.<h4>Upcoming Release:</h4>Mark your calendars! Volume 3 will be bringing even more classic gaming placards to your collection.&nbsp;<h3>Show Your Support:</h3>If you enjoyed printing and displaying these placards as much as I enjoyed creating them, please consider giving a Boost. Your support helps me continue to design and share more creations with the community.&nbsp;Add these new placards to your collection and keep the retro gaming spirit alive. Happy printing!

Game Console Placards - Volume 2

Signs

harrypulvirenti

It is basically an optimisation of the original design but is functionally the same. This remix eliminates a rear wall to use less material and makes overhangs less pronounced to make the model easier to be printed. I strongly recommend using brim to print it if you don't want to see the heel fall.You can find the suggested orientation used to print the object in the images.With the proposed orientation the object should fit without scaling it, you will maybe just need to move it a little bit into position, but some user reported that scaling it down to 95% also works well. &nbsp;I tested it with my X1C and is perfectly compatible. About the P1P the original model was compatible with the P1P without enclosure and this remix have the same compatibility

Engineering examples

Light Kit stuff

Phone Stands

NameTags

Signs

P1s stuff