Razbarey

Bobino

I came across a "straight one-way manual hand drill" by "zhwang168" "https://www.thingiverse.com/thing:4740760". I really liked his design so I followed his tutorial and made a bit wider and longer version with space for a 608RS ball bearing on top.I needed a chuck for this hand drill and the one I found on Printables matched exactly my requirements: "https://www.printables.com/model/309930-ez-drill-chuck". It can hold drills from 1,2mm up to 6,35 mm. I slightly modified it by adding a hexagon to the end so that I can attach it to the two way screw. I also renamed the parts to fit in my numbering but everything except "EZChuck-base.stl" is still the same. My name is MAN_DRILL-01-03.The one way drill consists of multi thread two way screw with a clutch that ensures that the drill is always rotating clockwise (or always anticlockwise if you rotate the nut assembly the other way around). On top by using one DIN934 - M5 nut and one DIN912 M5x18 bolt you attach a 608RS ball bearing that has a snap on cover for easy rotating holder.With one stroke the drill rotates four times so one up and down motion makes it 8 times. In 10 seconds I managed to do 28 “up and downs” so that makes it 1344 RPM (28*8*6)For the assembly of the drill chuck please follow the great tutorial on Printables mentioned above.The screw is assembled according to the second picture. For better action use some kind of lube.Then it is only a matter of attaching the drill chuck to the two way screw. The rotational movement is transmitted through the hex adapter so you can use a small piece of filament with lighter melted ends to secure it axially. For a cleaner look you can use a split pin DIN 94-2x22. This way I hope to try other 3d printed chuck or attach different attachments.This hand drill works well with smaller diameter drill bits around (3 mm) in wood, plastics and even in softer metals like aluminium and copper/brass. Bigger diameter drill bits (6 mm) are too aggressive. So to drill larger holes just slowly increase the diameter of the hole or grind more shallow angle on the larger drill bits.If the drill bit ever gets stuck, it is easy to hold the whole drill by the two way screw and rotate it clockwise a little bit by hand to break off the shavings.Print the drill chuck according to the instructions on the printables with added supports around the hex adapter. The hole does not need supports. The drill was printed entirely from PLA and was quite easy. The only part which might cause a problem is the two-way screw - MAN_DRILL-02-01 because it is quite thin and long (it fits PRUSA MK3S bed). It is best to print it standing up and . It is also advised to use supports in the hole for the nut. Rest of the parts are printed also standing up but these does not need supports.If you have any suggestions or problems feel free to reach to me. Enjoy.

1300RPM One way manual drill with chuck up to 6 mm

tools

michelem

<figure class="image"></figure>Make this upcoming Valentine&#39;s Day truly special with this irresistible Little Love Box and earn your well-deserved cuddles without having to print kilos of filament.&nbsp;Surprise your partner with a unique gesture: ask them to give a gentle push to the box, and the lid will soar away, revealing a red heart supported by a 3D-printed spring.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000157273/design/2024-01-26_b59347d20eb93.gif"></figure>&nbsp;Print&nbsp;DO NOT ADD SLICER SUPPORT for spring, read below.&nbsp;The printing process is a breeze, except for the spring, which requires a bit of attention and 0.12mm of layer height.&nbsp;But don&#39;t worry, I&#39;ve already included the necessary support in the design, so you won&#39;t need any additional supports.After printing it, carefully remove the support using tweezers, starting from the central hole. Try detaching the upper part by hand and continue with the tweezers until the spring is completely free. It works like a charm, I assure you!&nbsp;Assembly&nbsp;Assembly is straightforward: insert the spring into the base. If everything went well, you won&#39;t need glue; otherwise, use two drops for added security.&nbsp;Now take the plate and the heart (or just the heart) and glue them to the spring. Close it all with the lid and get ready to share all your love!&nbsp;You can choose to use the plate/frame for the heart or leave it without. Both have specially designed slots to be easily glued to the spring.&nbsp;Laughs and cuddles guaranteed!&nbsp;Happy Valentine&#39;s Day!&nbsp;UPDATE 01 Feb 2024<ul><li>Added a new box version with alternative text!</li></ul>

Little Love Box

gifts

SK07 Skipper07

I made this moon as a decorative element for my son's bedroom.In addition to being a moon with the function of a small house, it can also be used as a night lamp for your children.Inside the files you will find two variations of the main frame.the LED Moon House is designed for the passage of LEDswhile the other variant of the frame is more suitable for the decorative function.It can be hung on the wall using the holes on the back, or placed on the furniture using the support inside the files.I wish you a good print and I hope your children like it too.&nbsp;The new Moon lamp and added 12 programmable LED's & an esp32 chip for running W-LED to give the project the right lighting for everyday use.

Moon Lamp House

decor

Keppo87

Simple super colorful brick style container shelves, you can print them with the &#34;cap&#34; or without.&nbsp;You can resize them to your liking, I chose these dimensions to have more different models and to put small objects/miniatures on top.&nbsp;To add the supports under the protruding part, or otherwise use my already tested printing profile...  I will slowly add more photos and print profiles..&nbsp;Good print!!&nbsp;THIS IS THE NEW LARGER SIZE VERSION (copy and paste in your browser):&nbsp;https://makerworld.com/en/models/204864#profileId-225064

BRICK colorful storage shelves

lego

512IsGood

3D-printable cat mask, featuring a sleek low poly design.

Cat Mask with Low Poly Design

costume

NoycePrints

Meet Dum-E, the handy desk helper industrial robot. I designed it with purpose in mind as it can function as a phone stand, webcam mount (logitech c920) and a business card holder. It doesn&#39;t end there though, as I aim to develop this platform with further attachments in future. These may be recommended from others and/ or what I think might be useful. I hope you find it useful and please feel free to comment any recommendations for attachments you would like to see in future. I look forward to seeing your different uses/ prints and colour schemes. Thank you for your continued support :)&nbsp;To keep files from getting complicated, I have only included the phone stand attachment in this upload. I have placed optional attachments in a sperate upload available on my profile titled “Dum-E optional attachments”. This will be periodically updated with new wrist attachments I think may be of use or other people suggest. Printing helper<figure class="table"><table><tbody><tr><td>Part</td><td>Quantity</td><td>Infill</td><td>Supports required</td></tr><tr><td>Arm 1</td><td>1</td><td>25%</td><td>YES</td></tr><tr><td>Arm 2</td><td>1</td><td>25%</td><td>NO</td></tr><tr><td>Shoulder Joint</td><td>1</td><td>30%</td><td>YES</td></tr><tr><td>Wrist to attachment connector</td><td>1</td><td>40%+</td><td>YES</td></tr><tr><td>Turntable</td><td>1</td><td>20%</td><td>NO</td></tr></tbody></table></figure><figure class="table"><table><tbody><tr><td>Part</td><td>Quantity</td><td>Infill</td><td>Supports required</td></tr><tr><td>Base</td><td>1</td><td>20%</td><td>NO</td></tr><tr><td>Feet</td><td>1</td><td>20%</td><td>NO</td></tr><tr><td>XL motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Large motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Medium motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Small motor</td><td>1</td><td>15%</td><td>NO</td></tr></tbody></table></figure><figure class="table"><table><tbody><tr><td>Part</td><td>QTY</td><td>Infill</td><td>Supports required</td></tr><tr><td>Phone stand backing</td><td>1</td><td>25%</td><td>NO</td></tr><tr><td>Phone stand bottom</td><td>1</td><td>25%</td><td>NO</td></tr></tbody></table></figure>Required for assembly Superglue for fake motor attachment and Nitrile cord.1mm nitrile rubber cord, 16cm should be enough for 1 complete arm. This is only required between joints if you intend on supporting the weight of a phone etc. Alternatively, if you have TPU filament you can use Fat Tony&#39;s handy TPU O-rings. They&#39;re a quick print and don&#39;t require superglue to fit. You can get them here: <a target="_blank" href="https://makerworld.com/en/models/205832#profileId-225948" rel="nofollow noopener">https://makerworld.com/en/models/205832#profileId-225948</a> Thanks again for the great alternative Tony!&nbsp;As an optional extra, I&#39;d recommend using 4x 3M 6mm Anti-slip sticky back rubber feet. They fit in recessed circles in the corners of the feet.&nbsp; Screws: A total of 13 are required for the arm plus 3 for the phone stand, listed below.M3x10mm - QTY 12 - available on the store, linked below.M3x15mm - QTY 3M5x30mm - QTY 1Foot: 4x M3x10mm countersunk.Base: 1x M3x15mm countersunk.Shoulder joint to Arm 2 rotation point: 1x M5x30mm countersunk.Turntable: 4x M3x10mm countersunk.Rotation point between Arm 1 and Arm 2: 1x M3x15mm countersunk.Arm 1 to wrist connector rotation point: 1x M3x15mm countersunk.Coupling attachment to wrist: 1x M3x10mm countersunk.3 M3x10mm screws are required for the Phone stand. Assembly tipsCut 3 lengths of Nitrile cord, 74, 55 and 30mm in length. Glue one side of each and cure into individual circles. These will be glued on one side between the 3 separate joints on the arm. Doing this will vastly improve the holding capacity of the arm as it will provide more friction between the joints, helping to prevent them from sagging under weight.The 74mm circle goes between the elbow joint and arm 2.The 55mm circle goes between the arm 1 and 2 joint.The 30mm circle goes between the arm 1 and wrist attachment connector.I have added 3 pictures as a guide at the end of the gallery.

Dum-E the handy desk buddy. Lamp, stand, holder 

house use

Mimi home decoration

a kit card to build a cute easter landscape.can be print on A1 miniI used bambu filament basic brown, basic white, mat green, mat latte brown&nbsp;my others designs<a target="_blank" href="https://makerworld.com/en/u/2044748376" rel="nofollow noopener">https://makerworld.com/en/u/2044748376</a>

easter landscape kit card 

easter

the size is to fill in with kinder Chocobon or any sweeties, chocolates ….print all in 0,2 and glue each box.can be print on A1 minifor no ams change colors of the front boxes :layer 11 for the numbers and 15 for the ball .&nbsp;my others design <a target="_blank" href="https://makerworld.com/en/u/2044748376" rel="nofollow noopener">https://makerworld.com/en/u/2044748376</a>

Advent calendar / calendrier de l’avent

christmas

CoNcLuZiOn

Alphabet tiles designed to interlock like a puzzle, which can be used to spell words.

Alphabet puzzle letter tiles

education

3DMN

A sleeping fox from Minecraft! &nbsp;If you appreciate my work, give it a like, and if you love it, consider buying me a coffee to show your support! <a target="_blank" href="https://www.paypal.com/donate?hosted_button_id=BC7SWTMZG92TG" rel="nofollow noopener">https://www.paypal.com/donate?hosted_button_id=BC7SWTMZG92TG</a>

Minecraft Sleeping Fox

toys/kids

FunkyArt

A 100% 3D printed Smartphone-holder-arm that offers, at least, three axes. And the option of double braces between the axes. In the standard configuration, the arm easily supports around 500 grams in any position. &nbsp;The versatility of this arm enables secure and flexible positioning of smartphones or even tablets and cameras (coming soon) in any desired orientation. Print with high infill and clean up the prints carefully, the minimal gap dimensions of the 3D printed parts ensure reliable function and solid haptic but could also be hard for some printers. &nbsp;You find more additional features and alternatives in the Download section. I will provide more Instructions soon.&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=FxNsubX2KjE"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/FxNsubX2KjE" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;There are some additional upgrades in the download section, such as additional phone rotating movement and counterscrews, less tight screws and a bigger phoneholder.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/752785/2023-11-18_f7836c4a1c65.png"></figure><figure class="image image_resized" style="width:98.24%;"><img src="https://makerworld.bblmw.com/makerworld/draft/752785/2023-11-18_a6107c3f6e376.gif"></figure>What to Print?<ul><li>1x CZFA_Flexframe_BaseA_part11x CZFA_FlexFrame_BaseA_part2</li><li>1x CZFA_FlexFrame_PhoneMount (or the optional bigger one)</li><li>1x CZFA_FlexFrame_Mount-Mount (or the optional one with rotating axis)</li><li>1x CZFA_FlexFrame_Screw_cap-lid</li><li>1x CZFA_FlexFrame_Screw_small_Phoneholder</li><li>3x CZFA_FlexFrame_Frame_25cm</li><li>4x CZFA_FlexFrame_Screw</li></ul>Additional parts for rotating your phone, small phones adapter or counters crews..<ul><li>CZFA_FlexFrame_mount-mount-additional-movement-2-2</li><li>CZFA_FlexFrame_mount-mount-additional-movement-1-2 (you will need also one more small screw)</li><li>CZFA_FlexFrame_PhoneMount-small_phones_adapter</li><li>CZFA_FlexFrame_XL-PhoneMount</li><li>CZFA_FlexFrame_Counterscrew (optional to add more weight)</li></ul>Also less_tight versions of the screws.

Flexible & sturdy phone arm (100% Printed)

Craft Room

tisanina

This STL model represents a detailed and realistic rose, ideal for 3D printing projects or visual representations that require a touch of naturalness and grace

Rose

charms

Diana P

This is a small tray for any use (depends on the material you are using). I would recommend to make it at 100% infill.

Small tray

trays

MEAF designs

It doesn't matter what team you support, if you watch the games of the entire season or just the finals... this is the perfect accessory for any NBA lover. You can add it to your living room or bedroom. easy to print and perfect for the print size of almost any mid size printr. Files are separated so you can print it in multicolor without AMS. &nbsp;<figure class="image image_resized" style="width:25.76%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-07_6195f5960bc8.gif"></figure>&nbsp;Print SettingsMaterial: PLA / PETGLayer height: 0,2 - 0,28Nozzle diameter: 0,4mm or 0,6mmInfill: 10 -15%Perimeters: 2Supports: no&nbsp;yo can check all my designs here <a target="_blank" href="https://www.printables.com/social/281168-dgoalva/models" rel="nofollow noopener">dgoalva | Printables.com</a>

Basketball Tray

sports

l8nighter

<h2>Summary</h2>Thank You to z41d for the original design! A Syrian Hamster can get as wide as 80 mm so I took the original design from z41d and scaled it to 173% of the original (except for the connector) and the distance between the spirals are 80.01 mm. I printed everything in Sunlu PLA Transparent(Clear) (affiliate discount link below) and the normal tube with spiral's (used for the hamster to climb with) takes 3 hours 36 min and has about 5 layers of plastic and uses 112 g. I then removed the spirals on the straight parts and it takes 1 hour 59 min and has 3 layers of plastic and uses 56 g and also allows you to see the hamster better. At 173% the connector was too tight so I tried 175% and worked good. The problem is it took 2 hours to print and lots of supports to remove. By removing the middle ring and combining them together in 3D Builder it allowed it to print with only supports on the upper handle and I used Bambu White Support material with my Bambu X1 Carbon which made it super easy to remove. To print the 90 I also used Bambu White Support material which made is super easy to remove the supports. Finally, I designed an end cap so that you can make a section that has an end and the hamster turns around.&nbsp;Here is my affiliate discount link <a target="_blank" href="https://www.sunlu.com/?sca_ref=5346943.fSpGWrhJXW" rel="nofollow noopener">https://www.sunlu.com?sca_ref=5346943.fSpGWrhJXW</a> Click on PLA and search for PLA Transparent(Clear)