Rainer.Gregulla

Sevro

Overview.A Ring Lamp that can be changed to different situations. I designed base with various panels which can adapt to various style and occasion. You can simply change color of it as well as pattern on it, by changing color of diffuser and changing different panels.WARNINGSLed strips can emits some heat depends on what type of led you and voltage you use. In my case temperature of Main Ring achieve 60 °C . Due to this I recommend use filament that can resist that temperature especially for Main Ring. I tested ASA and it works well. Other high temperature filaments should work too (ABS, PETG but I didn&#39;t test it) PLA in this case can bend over time especially if you use heavy panel like budha.So in summary I tested and recommend :Main Ring - ASABase, Diffuser - PLAPanels- ASA ( PLA is possible but can bend )If you want change panel, always wait to cool down the ring lamp, otherwise PLA cover can bend during take off.&nbsp;Two Versions.There are two versions of Ring LampV1  - version 1 - First version of Ring Lamp. It is designed for 8 mm LED stripe.V2  - version 2 - Second version of Ring Lamp. It is designed for both 8mm and 12 mm LED stripes. I enlarged each piece by 110% so it now better takes advantage of bed size of the Bambu Lab printers.&nbsp;In the meantime, some designers created their own fronts for version 1. If you want to use fronts from other designers, make sure they are the right size. If they are too small, simply enlarge them to 110% in the X and Y axis as in the image below.&nbsp;<figure class="image image_resized" style="width: 38.09%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2024-03-28_867e2b9fbfc93.png"></figure>&nbsp;Electric parts you need.The easiest way is to buy electrical parts designed specifically for a ring light. Provides easy installation without the need for soldering.It is available on Amazon <a target="_blank" href="https://amzn.to/3zAnd6c" rel="nofollow noopener">https://amzn.to/3zAnd6c</a>It works with V1 and V2. <figure class="image image_resized" style="width: 37.08%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2024-06-30_880ecf419c351.jpg"></figure>&nbsp;You can also search for each part separately. You will need<ul><li>led stripe - best are LED COB </li><li>charger for LED strip</li><li>dc connector - I used 2.1/5,5 mm , the diameter of the mounting hole is 11.5 mm</li></ul><figure class="image image_resized" style="width: 21.19%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/8867176f-a9e4-4554-8087-7b1fd3a6b430.webp"></figure><ul><li>OFF-ON SWITCH</li></ul><figure class="image image_resized" style="width: 18.17%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/5cf1687e-913a-4186-92f2-75d8d2bac909.png"></figure>&nbsp;Printed PartsMain Ring, Base and Panels can be printed in draft mode 0.28-0.30 mm layer height with no issue.Diffuser should be printed with 0.2 mm layer height.<ol><li>After print, glue led strip to inner side of Main Ring</li></ol><figure class="image image_resized" style="width: 539.361px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/55f0a8a9-5b68-4a7a-b60e-def1c0cf337a.webp"></figure>Start from hole on bottom side<figure class="image image_resized image-style-align-center" style="width: 537.429px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/8f453fdd-01d6-476e-baaa-f03826eac490.webp"></figure>2. Put Main Ring into base. It should fit tight without glue.<figure class="image image_resized image-style-align-center" style="width: 538.864px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/f03a229b-e68e-4835-9d5f-37f66a2677d0.webp"></figure>3. Insert the electric part into the base and connect them by soldering<figure class="image image_resized" style="width: 535.014px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/2e73757c-be70-46f0-8fbb-ebc700b2e62a.webp"></figure><figure class="image image_resized" style="width: 531.08px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/75ca1515-ddbf-47b2-ab0d-34d6c3b795b9.webp"></figure>4. Insert Diffuser to Main Ring”. The Main Ring has a groove into which the Diffuser should be inserted and sit steadily. The flat side to the back.<figure class="image image_resized" style="width: 529.148px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/dd5e9b3f-84e4-47dc-8964-6b93b4f6ee46.webp"></figure><figure class="image image_resized" style="width: 527.23px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/3fc14977-a473-4279-b0d1-25f667c08fba.webp"></figure>5. Insert Panel into Main ring. The Panel has cuts at the bottom to avoid cutting the cables<figure class="image image_resized" style="width: 531.08px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/f414f9b5-fc71-4e83-af57-faf01b92199e.webp"></figure><figure class="image image_resized" style="width: 529.148px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163227/design/d3004065-f61c-4175-b595-6235c7b8ead8.webp"></figure>&nbsp;If you any question or suggestion write to me&nbsp;Have fun

Ring Lamp with replaceable panels

Lampen

schwaighoferart

Hier findet ihr unser Case, welches der Michael Riecks für die selbst gebaute Nebelmaschine erstellt hat.Das passende Aufbauvideo findet ihr unter: &nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=6gDedV5viwE&amp;t=2860s"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/6gDedV5viwE?start=2860" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;&nbsp;Luftpumpe: <a target="_blank" href="https://www.youtube.com/redirect?event=video_description&amp;redir_token=QUFFLUhqbnZUbUlVWkMxSnljUGNUdTR1aGxOVUNoUE92d3xBQ3Jtc0tucm84dG9BcFJQaV9fN19WclUtMVFiSmZDSVhVblFCblJ5czVoMDNwWkJSdkVNaWozbC1zYXNOaWVacnoxZFE1NWhkZnY1Y3BnYjhaa2QzcnFhUy1GU1FQU3pEenNzLWJHUGt2dU8xdUtEOWZnYmpxcw&amp;q=https%3A%2F%2Fshorturl.at%2FpFPX0&amp;v=6gDedV5viwE" rel="nofollow noopener">https://shorturl.at/pFPX0</a> Laderegler: <a target="_blank" href="https://www.youtube.com/redirect?event=video_description&amp;redir_token=QUFFLUhqbHpsdHZPMkR2OFZzemY1U3c1MjF4U0VqcDhLUXxBQ3Jtc0trU3RzczV5QzlsQlRUM1dBcGd4ZHZGUDBUamd2ZTlhcGE5N1V4YXBEdXVZVE9JVzBhVTZ1WmJLakVnZzBMb2pMck5hNG1rT2JWSDN6enJsSnYxcDNOTEdwT0x5VzdmSVpVLU9QMWJsVHg3Nm5GWElwVQ&amp;q=https%3A%2F%2Fshorturl.at%2FpuBMS&amp;v=6gDedV5viwE" rel="nofollow noopener">https://shorturl.at/puBMS</a> Ihr benötigt außerdem noch eine alte Einweg-E-Zigarette (Tornado RM7000) und einen Taster zum Ein und Ausschalten, Lötkolben, Kabel (Zweiadrig) und ein wenig Hausverstand ;)

BastlWastl Fogger

BastlWastl

Romwba3D

Following on from the sucess of my Rocker Gnome Model on Makerworld , i was asked to do a Christmas Version by some people , i have made two options for you , one with just a Santas hat ans one with him dresssed as Rudolph. I hope you like them and enjoy printing them&nbsp;A Cute Christmas Rocker Gnome / Gonk split for multi-colour printing, also split to enable printing with just one AMS or all in one with more than one AMS.&nbsp;i have also included a single colour STL file single colour or resin printing&nbsp;I have uploaded 3mf Print profiles for both the X1C/P1P and A1 Mini &nbsp;These are part of My Patreon <a target="_blank" href="https://www.patreon.com/romwba3d" rel="nofollow noopener">https://www.patreon.com/romwba3d</a>&nbsp;I have lots of Gnome / Gonks available on the patreon&nbsp;You can view all the Available Models - now over 200 on https://www.romwba3d.com

Rocker Gnome Christmas Version

Christmas

laisch

Low Profile Spoolholder for sidemounting to the bambulab AMS. With the bowdenconnector it adds just 34mm to the AMS in width. Fits spools from 140 to 200mm diameter. It mounts to the AMS with just clamping force, so there is no need to make any changes to the original hardware. Never unplug the AMS again when printing from an external spool.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_n6cdbyuzuuve.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_ajymv5zke7nc.gif"></figure>&nbsp;<blockquote>IMPORTANT NOTE: Before you print any part, read the Info part at the end of the build instruction!</blockquote>&nbsp;External Hardware:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_gpinzpf1se9r.jpg"></figure><ul><li>4pc - EXT5.55x25.4 tension springs or as an alternative 4pc small hair rubber band</li><li>4pc - M4x20 screw</li><li>5pc - M4x16 screw</li><li>9pc - M4 hex nut</li><li>9pc - M3 bras heat inserts</li><li>1pc - M3x6 screw</li><li>8pc - M3x4 screw</li><li>4pc - 608 rollerscate bearing</li><li>1pc - ptfe tube</li></ul>&nbsp;Print instructions:All parts print without supports!Everything can be printed in PLA, except the rollers should be printed in TPU. If you have no TPU, I added a PLA version for the part also. You can't just print the TPU part in PLA, because its undersized, and pressing the bearing in it would cause it to fail.&nbsp;Build Instructions:Drill holes After printing the Mainholder, you have to drill out the holes fot the rollers with a 4mm drill to later fit the screws. If the M4 screws fit, you can skip this step. The holes are made exactly 4mm to ensure the slicer makes 5 perimeter for strength. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_wmuhfakemqad.jpg"></figure>&nbsp;Heatinserts The M3x4mm brass inserts have to be placed at the sliding mechanism and on the hole where you want the bowdenswivel to sit later. (The parts are designed for 4mm deep inserts, but it's also possible to use 6mm ones like I did because I had too less 4mm ;) )<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_a60ufmrmawm1.jpg"></figure>&nbsp;Tension Springs:<blockquote>My prefered method is to use the rubber bands, even when the spring solution looks way nicer. But the springs tend to be too strong and overstretching them doesn't make them look nice.</blockquote>For the sliding mechanism you can use either tension springs or rubber bands. When using the springs, make sure that an empty spool will stay in place and don't get pushed out because the spring force is too strong. In case it's too strong you can widen the springs, but if they are too wide, a 140mm spool wont fit anymore.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_afhhdqdtdght.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_mmeizzw31hva.jpg"></figure>Use the M3x4mm screws to screw the springs in place&nbsp;Rubber Bands: Install the rubber bands like the springs. One per slot has enough force to hold the spool.<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_s1ktst97rhlt.jpg"> Assembling the rollers: Press the bearing into rollerpart 1<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_lpzxkn799hjr.jpg">Add superglue and slide the two halfes together<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_8nkfcmbp9t4k.jpg"> <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_k17jdkrkcwv3.jpg"></figure>&nbsp;Installing the rollers: Insert the M4 hex nuts into the back of the Mainholder.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_3bgoc2k932xp.jpg"></figure>Add the Roller and the Spacer and screw them together with the M4x20 screw<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_vh6j1s4i5g84.jpg"></figure>&nbsp;Installing the PTFE Swivel After printing the swivel, make sure that the two parts can rotate. Press the PTFE tube into the swivel and screw it to the Mainholder<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_f2aek2jdswpi.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_xr3j0fuxpsfh.jpg"></figure>&nbsp;AMS Mounting: Connect the clamps with M4x16mm screws and M4 nuts loose to the Mainholder.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_n7cubyc4xkmj.jpg"></figure>Slide the whole assembly to your AMS and tighten the screws<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_1dmqtqzdpmt2.jpg"></figure>When the spoolholder with a full spool installed flexes too much you can also use double sided tape for better adhesion.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_vuzqa96gaaqw.jpg"></figure>&nbsp;CONNECTION:For connecting the AMS, the LP-Spoolholder or/and a filament dryer you can use my <a target="_blank" href="https://makerworld.com/en/models/74010" rel="nofollow noopener">3-Way Bowden Splitte</a>r:&nbsp;<figure class="image"><a href="https://makerworld.com/en/models/74010" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-25_580b350a182a5.jpg"></a></figure>&nbsp;AMS RISERIf you want to use the LPSH with an AMS - Riser, I recommend to check out the<a target="_blank" href="https://makerworld.com/en/models/86200" rel="nofollow noopener"> Mooser Project</a> by <a target="_blank" href="https://makerworld.com/en/u/2178842856" rel="nofollow noopener">Basti85</a>. It was designed to be fully compatible with the LPSH. His risers has already included the throughholes for the LPSH - Spoolholder. &nbsp;<figure class="image"><a href="https://makerworld.com/en/models/86200" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-12-09_9418658cdf1eb8.jpg"></a></figure>&nbsp;&nbsp;&nbsp;IMPORTANT INFO PART<blockquote>TIP: If the rollerslides are jamming from time to time, you can add some lubrication to the slider. I used the same silicon lube wich I use for the lead screws AMS: There seems to be different versions of the AMS. So before you print the clamps, check the rib size of your AMS. If you have 4 Ribs wich are 65mm - 86mm - 65mm appart, you can print the clamps like they are in the print profile. If you have 6 ribs wich are about 45 - 43mm appart you have to just print the "Clamp_small_18mm" at least 3 times Clearance Issue One user encountered too much clearance on his sliders wich leads to too much sagging of the spool. So I added three clearance test prints. The original "Mainholder" part comes with clearance 0.2mm. So print out the three clearance prints first and then decide wich "Mainholder" - version you want to print. For the sliders to work perfektly they must slide with ease (lube if necessary) but should not have too much wobble. Heat Inserts: There are 2 Types of M3 heat inserts. The one I used originally have ~5mm in diameter. If you are using the ones with 4mm outer diameter, there is a file called “holefix _4mm.stl" wich you can load together with the Mainholder.stl into the slicer. Just mark both files, pull them to your slicer and say "yes" when Bambu studio is asking if you want to load it as a single object. For those who want to go anyway with the rubber bands I added a "rubberplug" - part wich can be used instead of the heat inserts. There are also two versions, one for the original 5mm holes and one for the holes with the holefix for 4mm.&nbsp;Tension springs vs. rubber band My prefered method is to use the rubber bands, even when the spring solution looks way nicer. But the springs tend to be too strong and overstretching them doesn't make them look nice. UPDATE 21.11.23: - made the bowdenswivel stronger and added two different sizes 20mm and 30mm&nbsp;Update 31.12.23: - Holefix_4mm.stl for 4mm diameter heat inserts</blockquote>&nbsp;

Lampen

BastlWastl

Christmas

Printer

Boxes