RaDoLe

jtebs

&nbsp;Update Added updated model and instructions for A1 Mini. Skip to the bottom for install directions&nbsp;Got tired of constantly bumping into my old desk cup holder so I designed one that not only pulls out from under the desk but is retractable as well.&nbsp;The retracted cup itself measures roughly&nbsp;75 mm deep94 mm wide top81 mm wide bottom&nbsp;Because of the retractable nature of the holder I wasn&#39;t able to design it with a cutout for coffee mug handles sadly but, it will accept most normal glasses, bottles, even my 30oz Stanley water Cooler.&nbsp;The holder is designed with 3, 6mm x 3mm magnet holes. The magnets aren&#39;t required but do give the holder a satisfying “snap into place” feel when you&#39;re deploying or retracting the cup holder away. These are the magnets I use <a target="_blank" href="https://www.amazon.com/gp/product/B096LZNZTQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B096LZNZTQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1</a>&nbsp;&nbsp;&nbsp;&nbsp;Installation Instructions&nbsp;Optional stepInstall the 3m x 6m magnets in the cup holder (1x) and cup holder sleave (2x). The magnets should fit in pretty snuggly. You may want something hard and flat to use to fully press them in.&nbsp;&nbsp;Step 1. Print out the guide included in the project. From there, place the guide on the underside of your desk where you&#39;d like the cup holder to go and make sure it&#39;s hooks are flush with the front of the desk. Mark the 4 mounting holes<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_0cde14eeadefb.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_73874aa80ef2.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_2b81f29166678.png"></figure>&nbsp;Step 2.Put the cup holder in the Cup holder sleave. Line the mounting holes up with your marks and check that the unit lines up with your desk correctly. A correct install will have the edge of the cup holder almost flush with the edge of your desk.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_d111c6f78a453.png"></figure>&nbsp;Step 3.Remove the cup holder and line up the Cup holder sleave mounting holes with your marks. Use 4 screws to attach through the mounting holes<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_b2740a5e63032.png"></figure>Step 4.Re-insert the cup holder and screw the printed Bolt up through the bottom bolt hole. This bolt makes sure that your cupholder doesn&#39;t slide out of the sleave when you pull it out.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-09_808d1a69971da.png"></figure>Step 5.Retract the holder and begin your new cup holding journey! If you need to remove your cupholder for cleaning just unscrew the securing bolt and pull the cupholder free.&nbsp;Print instructions&nbsp;The holder itself is 3 pieces&nbsp;Cup holderCup holder sleaveSecuring bolt.With an optional 4th piece which is the mounting guide.&nbsp;-The Holder and bolt will print out together. The sleave and guide will need to be printed on their own.-Both the holder and holder sleave are set with 10 mm brims as I was having issues with the filament I was using warping off the bed. If this isn&#39;t an issue for you, feel free to turn off brims.&nbsp;No supports needed and the retractable cupholder is all print in place. Only assembly needed is already noted in the installation guide above&nbsp;<h2>A1 mini install instructions</h2>Disclaimer: While I did print out and test the model for the A1 mini, I do not have the printer (printed on my p1p). I&#39;ve redesigned it to specifically fit within the A1 mini specs but please let me know if some aspect of the build doesn&#39;t work. Also, while I did save the project specifically for an A1 mini, I&#39;m not sure if my p1p AMS settings will mess with anything. So just be sure to double check before printing.&nbsp;Step 1. Download the A1 mini project file&nbsp;Step 2. Print out the model broken into 3 plates. The cup holder, the sleave, and the 2 locking bolts.&nbsp;Step 3. (optional) Install the three, 3mm x 6mm magnets. 1 on the cup holder and 2 on the sleave. They should fit snuggly but if they are a little loose, i recommend a dab of super glue to keep them in tight. As noted above, these are the magnets I use <a target="_blank" href="https://www.amazon.com/gp/product/B096LZNZTQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B096LZNZTQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1</a>&nbsp;Step 4. Place the sleave on the underside of your desk where you&#39;d like to install. Make sure that the front “struts” are flush with the edge of your desk<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-17_5b84e6f635a87.png"></figure>Front studs flush<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-17_a460b2a0e4528.png"></figure>Step 5. While holding the sleave in place, slide the cup holder in to verify that it&#39;s fully under the desk when in the sleave<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-17_cce9e8058f1fc.png"></figure>Step 6. Remove the cup holder and use 4 screws to mount the sleave to the desk.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-17_e666a327f92b7.png"></figure>Step 7. Slide the cupholder back in and screw in the 2 locking bolts on either side of the sleave. If you need to remove the cupholder for cleaning, simply unscrew the locking bolts.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000422152/design/2024-04-17_b3ea466c29ecd.png"></figure>&nbsp;That&#39;s it, get to cup holding!&nbsp;This has been working out great for me, hopefully its equally helpful for you! Happy Printing!

Retractable Desk cupholder

Tools

Jaspyjo

Find V3 here: <a target="_blank" href="https://makerworld.com/en/models/423637#profileId-326893" rel="nofollow noopener">https://makerworld.com/en/models/423637#profileId-326893</a>&nbsp;Version 2 of my top glass riser. I added a bambulab emboss for aesthetic reasons.&nbsp;Cleanest and most simple top glass riser out there (in my opinion). No support necessary, 15% Infill, quick and easy print.&nbsp;For the P1S, likely also works on the X1C.

Top glass riser BambuLab Emboss *V2* [P1S and X1C]

PrinterStuff

Somusgrove

3x2 Gridfinity to store 2 medium cable organizers made by Squinn. Fits perfectly in an IKEA Alex drawer with the gridfinity base.Link to the original cable winder: https://makerworld.com/en/models/13849#profileId-13650

Portable Cable Organizer Gridfinity Storage 

Gridfinity

The Big Greek

Toilet Sign “Whatever”&nbsp;No more word needed :-)&nbsp;Quick and easy to print, use double-sided adhesive tape for mounting.&nbsp;If you like my work/project consider supporting me with these options:<ul><li>leave a like</li><li>leave a comment</li><li>download the file</li><li><a target="_blank" href="https://www.buymeacoffee.com/thebiggreek" rel="nofollow noopener">or By me a Coffee</a></li></ul><h3>This article/post/text or the print profile as well as the finished print may not be used for commercial purposes.</h3>Have fun printingTBG&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/731522/2024-03-19_708d9a93b787c.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/731522/2024-03-19_dc1944ad1bd98.png"></figure>

Tools

PrinterStuff

Gridfinity

DecoStuff