PolyCraftLab

halil_d

A1 / A1 Mini Kabelführung 

A1 Mini Accessories

jarvizar

3d miniature of the Nürburgring in Nürburg, Germany!&nbsp;Includes an AMS-compatible multicolor print profile highlighting both the Nordschleife & Grand Prix circuit! (AKA the 24hr layout)&nbsp;Model created in Blender primarily using data from the <a target="_blank" href="https://github.com/vvoovv/blosm" rel="nofollow noopener">Blosm</a> addon.&nbsp;&nbsp;Smaller Nürburgring highlighting the GP circuit: <a target="_blank" href="https://makerworld.com/en/models/180660#profileId-198781" rel="nofollow noopener">https://makerworld.com/en/models/180660#profileId-198781</a>&nbsp;Check out my collection of other miniatures: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/146964" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/146964</a>&nbsp;Collection of F1 Miniatures: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/450282" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/450282</a>&nbsp;<h3>Slicing & Printing Details</h3>&nbsp;This model was designed to be printed with a 0.4mm nozzle and 0.16mm layer heights.Try using a 0.2mm nozzle (0.08mm layer heights) or scaling up for even finer detail!&nbsp;Note: If roads or other small details disappear after slicing, try lowering the extrusion/line width of external perimeters (outer walls) closer to 0.4mm OR use Arachne walls (can also enable “Detect Thin Walls”). The included “Designer Profile” should have the above settings pre-applied and is ready to slice & print!&nbsp;Filament used in photos: Sunlu Matte White (miniature), Bambu Matte Charcoal/Black (frame), Sunlu Sky Blue (water)&nbsp;<h3>Framing Details</h3>&nbsp;This model measures almost exactly 7.5x9.5in (242.31mm X 191.08mm) and should fit most 8x10 frames (assuming frame lip/overlap is around a half-inch). Feel free to change the scale/size of the model(s) to meet your needs.&nbsp;&nbsp;I also included a large printable frame designed to fit my large miniature cities!&nbsp;Note: This is a “large” miniature and will not fit the smaller ~5x7inch printable frame included with the other miniature cities!&nbsp;&nbsp;Personally I use these cheap 8x10 frames from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B08XVP48KQ" rel="nofollow noopener">https://www.amazon.com/dp/B08XVP48KQ</a>And blue printer paper: <a target="_blank" href="https://www.amazon.com/Astrobrights-491618-Multipurpose-8-5-Inch-11-Inch/dp/B00006IDQT" rel="nofollow noopener">https://www.amazon.com/dp/B00006IDQT</a> (not needed for this model since there is no “water”)&nbsp;&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;&nbsp;See my <a target="_blank" href="http://patreon.com/jarvizar" rel="nofollow noopener">Patreon</a> for a commercial license, early downloads, polls towards future models, and more!&nbsp;

Nordschleife Nurburgring 3D Mini (Large)

Future Prints

thrutheframe

<h3>NOTE:</h3><ul><li>Please read the instruction guide below</li><li>I do my best to double-check and test the print profile I create. They are up to date with whatever changes I made to the designs. If you are using profiles made by others, please check if they are updated.</li></ul>&nbsp;<h3>UPDATE: 3 JAN 2024</h3>I have added a version of the BIN that will work with the Bambu Lab Z-Stiffener. It is on Build plate 2.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2024-01-03_8bd5d74720bb9.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2024-01-03_16b719cd2144e.png"></figure></td></tr></tbody></table></figure>&nbsp;<h3>INTRODUCTION</h3>All Bambu printers poop. So here is a Poop Management System (PMS) for A1. The system consists of a purge guide and a bin. I have added the <a target="_blank" href="https://makerworld.com/en/models/91481#profileId-97865" rel="nofollow noopener">Stabilization Bracket for A1</a> in this project build plate. You might want to try using it with/without the <a target="_blank" href="https://makerworld.com/en/models/90586#profileId-96991" rel="nofollow noopener">GRIP bracket</a> to improve the stability of the A1 printer.<figure class="table" style="width:89.28%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_c0abab96e0d06.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_ac7c55c15ff49.jpg"></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_170cda32f15e3.jpg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_508805f48faf6.jpg"></figure></td></tr></tbody></table></figure>&nbsp;<h3>INSTRUCTION</h3><ul><li>Print build plates 1 & 2</li><li>Paste a piece of tape over the area as shown in the image below. During purging, the tip of the purge can still be molten and can accidentally adhere to the wall. The tape helps to reduce the chance of this happening.</li><li>Slide the purge guide into the purge wipe as seen in the image. It should fit snugly.</li></ul><figure class="table" style="width:96.81%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_19a14b0cca0d8.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_aa7a5482d8532.jpg"></figure></td></tr></tbody></table></figure>&nbsp;<ul><li>The bin should be fitted into the left Z-beam as seen in the image below.</li></ul><figure class="image image_resized" style="width:59.91%;"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_64830ac1a7016.jpg"></figure>&nbsp;<ul><li>Turn on the A1 printer and do a home to ensure proper clearance.</li><li>All the best and welcome to a poop-free table.</li></ul>&nbsp;&nbsp;&nbsp;“Friends do not let friends poop everywhere…” Poobymeister<figure class="image image_resized" style="width:60.09%;"><a href="https://thangs.com/designer/DaveMakesStuff/3d-model/Doggy%20Poo%20Candy%20Box-973574" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/346126/2023-12-13_e2df74deec799.jpg"></a><figcaption>Doggy Poo Candy Box by DaveMakesStuff</figcaption></figure>&nbsp;<h3>CONCLUSION</h3>To date, my designs are free to download and use. There is no Patreon or OnlyFan (hahaha). If you like my designs and wish to contribute to my coffee addiction & help fund the filaments and materials needed for prototyping, a donation of $5-$10 to <a target="_blank" href="https://ko-fi.com/thrutheframe" rel="nofollow noopener">Ko-fi</a> or <a target="_blank" href="https://www.paypal.com/paypalme/shannonheng" rel="nofollow noopener">paypal.me</a> will be greatly appreciated.&nbsp;<h3>CAVEAT</h3>As with all my designs, Prototyping and testing were conducted to ensure printability and meet my own expectations. However, I understand it may and may not work for you. I would request that you read all instructions and print and install them at your own discretion.

A1 Mini Accessories

Future Prints

A1 Upgrades