Pinsceau Printer

automontronic

Can be printed at .28mm layer height without issue. There are two versions of the top. A blank top or a top with an embedded plane.

Passport Travel Box, Travel Case

Travel

man1ac

Found the linked Version on Printables but thought it had some flaws: Dimensions for my Decks weren't perfect. The Lid mechanism was quite thin and either bend or broke off.&nbsp;This Box has has these things (and more) optimised to be printed in PLA and no free hanging structures.It cant hold a standard 100 card commander deck with about ⅓ double sleeved (KMC Perfect Size).I redesigned the lid and engraved the commanders I have.&nbsp;I attached a picture of the lid in detail. The overall dimensions of the lid are 73.6 x 87.7 mm (the absolute final fit will be dependend on your printer so maybe you will need to change 0.2-0.3mm)

MTG Commander Deckbox Box 

maxaruta

This photobox features a 360-degree rotating base, which allows you to take photos from any angle. It is also fully customizable, thanks to the variety of wall styles available. With my photobox, you can significantly improve the perceived quality of your products to your customers. Your photos will be more professional and engaging, and your customers will be more likely to purchase them. Download the model today and start taking professional photos of your creations! _____________________________ Ti presento la mia nuova photobox, lo strumento perfetto per creare fotografie professionali delle tue stampe e creazioni.&nbsp;Questa photobox è dotata di una base d'appoggio ruotabile a 360 gradi, che ti permette di scattare foto da qualsiasi angolazione. Inoltre, è personalizzabile al massimo, grazie ai vari stili di pareti disponibili.&nbsp;Con la mia photobox, potrai migliorare notevolmente la qualità percepita dai tuoi clienti dei tuoi prodotti. Le tue foto saranno più professionali e accattivanti, e i tuoi clienti saranno più propensi ad acquistarli.&nbsp;Scarica il modello subito e inizia a scattare foto professionali delle tue creazioni!

Photobox: Take professional photos of your creations

Miniatures

m.cody.sims

Just a good Mando helmet!&nbsp;My profile doesn&#39;t have support on the inside of the helmet because I have found it didn&#39;t really help that much with the quality and it used a lot of filament. the very center of the inside will be rough because of this but it hasn&#39;t been an issue for me.&nbsp;For those wondering what I use for a face sheild I use a Hobart 770580 Face Shield Replacement Lens, Shaded from Amazon. I cut it to shape and use a little bit of hot glue along the front and near the temples. That seems to be enough. I would recommend getting air soft helmet padding for a custom fit and comfort.&nbsp;If you like my work, please consider supporting me by boosting my model or <a target="_blank" href="https://www.buymeacoffee.com/m.cody.sims" rel="nofollow noopener">buying me a coffee</a>!

Mandalorian Helmet One Piece

Cosplay

JamesThePrinter

** Get an early start! Get the <a target="_blank" href="https://makerworld.com/en/models/41177" rel="nofollow noopener">Christmas version</a> now! **&nbsp;&nbsp;Light up different Halloween scenes in this display. A tea light candle is required. The display features a door that opens to allow access to the tea light. Use a section of 1.75mm filament inside the hinge to connect the door to the case. Depending on your printer/setup, this hole may be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.I have included a separate liner. This allows you to print the case in a dark color, but line the inside with a lighter color to allow for more reflection of light outward, making everything brighter.For a complete display, you will need:<ul><li>1x Case</li><li>1x Door</li><li>1x Knob</li><li>1x Snap Ring</li><li>1x Liner - Optional</li><li>1x (minimum) Scene - You can easily remove the snap ring to swap out scenes as desired</li></ul>Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.<h4>Print Settings</h4>No special setting are needed for the display case, door, knob, snap ring and liner. &nbsp;Scenes Print SettingsPrint the scenes with 100% infill. The scenes also require color changes:<ul><li>The top 2 layers should be black</li><li>If there is no moon in the scene, all other layers can be white or clear - both look nice</li><li>If there is a moon in the scene, it will look best if the bottom 2 layers are printed in clear filament<ul><li>All other layers should be white</li><li>All non-black layers could be printed in all white or all clear if one isn't available to you</li></ul></li></ul>&nbsp;<h4>Assembly</h4>Glue the knob into the door. Only a very small amount is needed.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_njhnxlluv3as.png"></figure>Put the door in place and latch it. Use a 20mm piece of 1.75mm filament to connect the 3 sections of the hinge. If the filament goes in very easily, it may be a good idea to heat up the top end of the filament ‘pin’ and press it flat. This will prevent the pin from falling through later on.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_ps9jc73zrxio.png"></figure>Open the door. Insert a scene into the opening (image facing outward). Insert the snap ring behind the scene by gently squeezing and placing it into the groove (see red arrow below).<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_zosx4sj7pb0v.png"></figure>If you are using a liner, slide it inside the case. This may be a tight fit. Go slowly and be sure to slide it in evenly on all sides.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_t3jeg8v9f9hv.png"></figure>Turn on your tea light and close the door.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li><li>GIANTARM Transparent Clear PLA</li></ul>

Halloween Tea Light Display

Decoration

matthiasdeblaiser

Made this because I was frustrated by bottles constantly falling after doing the dishes. This way they can drip all they want without the risk of falling. And they're quickly put aside for when you need some extra room Designed for the max print volume of the Bambu Lab X1C with the filament cutter enabled. (no the build surface is not full 256x256mm) and leaving some room for a brim (tabs in this case). I landed on a 235mmx235mm max dimension of the model.A brim caused errors (gcode out of bound or something like that even though the prime lines were even beyond the print) so I made some little bitty tabs that probably don't do much anyway… (it didn't warp on my first try, but is that because of the tabs? no one knows)With a few minutes of shifting the model around I finally landed on this size that was printables (not a mm to spare). It's very well possible that with some tweaking (such as disabling the filament cutter) you can make it a little bit bigger. But it's big enough for me so I didn't bother. The little cutout for the filament cutter area does not hinder functionality, as long as you put a narrow capped bottle there (see picture)I also included a non Bambu Lab model without the cutout and tabs (and little bit lower rim) which also measures 235x235mmPrint the step file if you can, it makes for much smoother circles and faster printing, which I only realized after printing this 480g beast for 10 hoursAnd if you wonder why the rim is so high, that for rigidity :) not for stopping the water at that height&nbsp;I printed this with a very old leftover roll of PLA. 0,4mm nozzle and 0,25mm layer height. Used a textured PEI bed WITH spray on glue for maximum adhesion on the corners. Bambu Lab X1C specific: Disable your auxiliary fan or you will get warping !&nbsp;&nbsp;Edit: 3 bottle version added as per request

Travel

MTG

Miniatures

Cosplay

Decoration

Home Stuff