NerdMuse

Onkelsam

simple 2d wall art&nbsp; Perfect print bed adhesion is extremely important for the pointed ends&nbsp;Easy to attach with double-sided tape

Wolverine claws wall art

Skadis

DatumCAD

<figure class="image image_resized image-style-side" style="width:38.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/805986/2024-03-20_394e64d5f2285.gif"><figcaption>GIF - Exploded View Animation</figcaption></figure>An adjustable handle that can be attached to any existing standard full-size hacksaw blade. This compact tool allows you use the blade in tight / hard to reach areas, and where a full-frame would foul with the material.&nbsp;I also have various other models for various blade types &amp; are yet more compact in size. Feel free to check those out too:<ul><li><a target="_blank" href="https://makerworld.com/en/models/386059#profileId-286421" rel="nofollow noopener">Junior hacksaw handle</a></li><li><a target="_blank" href="https://makerworld.com/en/models/400706#profileId-302219" rel="nofollow noopener">Jigsaw blade handle</a></li><li><a target="_blank" href="https://makerworld.com/en/models/410315#profileId-312254" rel="nofollow noopener">Reciprocating saw blade handle</a></li></ul>All designs incorporate opposing dual thumb CAM levers with positive snap shut to ensure the blade does not slip once held &amp; it is as safe as possible to use. This took a lot of prototyping &amp; testing but works great. It is quick &amp; toolless to adjust….and satisfying to use as a result.&nbsp;Most standard ‘full size’ hacksaw blades are 0.5&#34; (12.7mm) wide by approximately 0.6 - 0.7mm thick, if you want to double check yours for compatibility as anything this wide (or smaller) should fit fine.&nbsp;Note: The CAM levers have been deliberately designed to be tight fitting to avoid the blade slipping in the tool. That said, if after the first few engagements &amp; releases of the thumb lock it has not eased to a point you are comfortable using it, then you could try printing the smaller CAM levers from the Print profile provided. Additionally, if you have a thinner than standard blade or a loose fit, then you may want to print the Larger CAM Levers profile.&nbsp;If you like this model then you may also like my sliding <a target="_blank" href="https://makerworld.com/en/models/213504#profileId-233069" rel="nofollow noopener">steel ruler limit block</a> which also incorporates a CAM locking mechanism. Or any of my other <a target="_blank" href="https://makerworld.com/en/@DatumCAD" rel="nofollow noopener">DatumCAD</a> designs :)&nbsp;Fasteners: For this model you will need 2x M3 x 30mm fixings which act purely as strong pivot axles to the cam lever.&nbsp;Assembly:<ul><li>Insert the CAM lever into the Housing. Tip: Insert with the level in the closed / horizontal position as the holes will then line up easier.</li><li>Insert M3 Fixings. Tip: The fixings should pass though the handle housing counterbore hole &amp; the CAM lever relatively unhindered, but then will need lightly screwing into far handle hole which has been deliberately sized so as to require some tightening without to much force. (Remember these are just acting as pivot points, no need to tighten down hard, but equally the fixing should not want to fall back out either.)</li><li>Insert Blade. Top Tip: Open both of the CAM levers up around 180degrees from the closed position, so the CAMs don&#39;t grab the blade upon insertion. Once you have in the desired location, simply lock both CAMs fully down.</li><li>Enjoy - your adjustable hacksaw handle is now ready to use.</li></ul>I love designing for 3D printing, please take a look at all my other models which are all free (and will always continue to be)… if you value any of the downloads enough &amp; are able to support me, then please consider buying me a coffee to keep me going! <a target="_blank" href="https://www.buymeacoffee.com/DatumCAD" rel="nofollow noopener">www.buymeacoffee.com/DatumCAD</a><figure class="image image_resized" style="width:55.06%;"><img src="https://makerworld.bblmw.com/makerworld/draft/805986/2024-03-21_6e3d9fd6f9586.jpg"><figcaption><a target="_blank" href="https://makerworld.com/en/models/386059#profileId-286421" rel="nofollow noopener">Link to Junior version</a></figcaption></figure><figure class="image image_resized" style="width:55.01%;"><img src="https://makerworld.bblmw.com/makerworld/draft/805986/2024-03-20_278390d1fc3bb.png"></figure>

Ultimate Hacksaw Handle

Tools

3DPrintBeginner

I recently moved from using a PC to a <a target="_blank" href="https://amzn.to/3NT24qN" rel="nofollow noopener">MacBook Pro 14</a>. The laptop is still connected to a bunch of displays and peripherals so I wanted to have a nice stand for it. But from a simple laptop stand, I eventually got to making the HexaHive Stand for MacBook. The HexaHive Stand has the following features:1. Perfect angle for having the screen at 90 degrees when open. 2. Raises the laptop to a comfortable height which helps with correct posture (Screen base is at 27cm) 3. It’s sturdy and stable, to keep your laptop safe during use 4. Wire management openings in the base, to route the cables easily and keep your desk tangle-free. 5. Designed to be fully compatible with both <a target="_blank" href="https://3dprintbeginner.com/macbook-pro-14-review/" rel="nofollow noopener">MacBook Pro 14</a> and MacBook Pro 16, but it can work with similar laptops too. 6. Can be 3D printed with no supports 7. Ready for future upgrades that can be attached to the hexagons.

HexaHive Stand for MacBook Pro 14/16 - Hexagonal Laptop Stand

Desk

Snapmaker 10W Laser Lens Cover

1.6W (1600mW) Snapmaker Laser Lens Cover