MrMarco11

luckyluc.64

The best PTFE guide plus PTFE Release (no tools require).There it is. Many Makers asked me for this after seeing the one I designed for the AMS Hub.<a target="_blank" href="https://makerworld.com/en/models/73523#profileId-77971" rel="nofollow noopener">https://makerworld.com/en/models/73523#profileId-77971</a>Since the location is good, I didn&#39;t add a subplate and relocate the buffer. The drawback is that I only have a little wire management.&nbsp;In a certain way, it&#39;s better because there are no holes to tap or screws. It just &#34;Smap in place&#34;.It&#39;s also easy to assemble;-Release the two PTFEs from the buffer.-Snap the central part on top of the AMS Buffer. (See the pictures above) (injector end first and snap the other end)-Slide in the two PTFE guides and secure them with the &#34;C&#34; ring. (The longer one goes in the Injector side)-Push in the two PTFEs. Tug them back to see if they lock in place.It&#39;s ready to go. Thanks to the realignment of the PTFE in the fittings, you won&#39;t need other tools and will avoid jams.It&#39;s not a bad idea to chamfer the inside of the PTFE after cutting it.&nbsp;After printing, make sure the holes are clean. The guide should slide easily and freely into their mount. It may require a little filling in the bores.&nbsp;I did test it with PLA. And the small tube broke. Then, No, you can&#39;t use PLA.I test-printed it with PETg, which prints well for the P1P one. It works well, and no support is needed (But it can&#39;t hurt). I didn&#39;t have to file or sand the bore, but it may be required (Especially if you use generic material and print on a series P1; the flow is critical). The injector side guide must slide freely, and the PTFE should slide into the guide freely. It doesn&#39;t matter if the PTFE slides into the guide or the guide slides with the PTFE.Of course, I did make it in ABS. It&#39;s the best for me and my favorite BBL Blue ABS.&nbsp;It prints in an hour and a half in PETg and is even faster with ABS.Enjoy.

AMS Buffer Injector Guides

Bambu Lab

Markury

I saw a tiktok with a keyboard that was all ducks and I had to have one. This one is only suitable as an escape key or similar since they don't like to sit next to each other. Edit: An experimental “v2” version is provided that has enough clearance for multiple ducks to sit next to each other. Still, this version does not address that keys interfere with each other in adjacent rows. I did make an updated version, and it's available for purchase on the orange website that starts with a “P” on my profile, Markury.&nbsp;Please share your makes. Happy printing!&nbsp;Note: My print preset has supports under the beak with support blockers inside the keycap. You might be able to get away with no supports if you slow it down enough.

Ducky Artisan Keycap (AMS)

Computer

Sakul

🍌 Peeled Banana Lamp 🍌 I know you all love bananas, and now you have the chance to light up your room with this stimulating statement piece. The lamp is designed to work with a <a target="_blank" href="https://www.amazon.de/Eco-Luma-Neutrales-Halogenlampe-Gl%C3%BChlampe-Flackern/dp/B09T9947K9/ref=sr_1_5_pp?crid=HPQKR2D9638R&amp;keywords=g9%2Bled&amp;qid=1707167329&amp;sprefix=g9%2Caps%2C115&amp;sr=8-5&amp;th=1" rel="nofollow noopener">G9 LED lightbulb</a>, otherwise, you only need <a target="_blank" href="https://www.amazon.de/Gl%C3%BChbirnen-Lampenfassung-Keramik-Silikonkabel-ISOLATECH/dp/B094QQTYZL/ref=sr_1_5?crid=2IVMRCJPR1WXF&amp;keywords=g9+fassung&amp;qid=1707167361&amp;sprefix=g9+fass%2Caps%2C101&amp;sr=8-5" rel="nofollow noopener">1x G9 lamp socket</a>, 2x M3x16mm screws, <a target="_blank" href="https://www.amazon.de/EMOS-Stromkabel-Ersatzkabel-Anschlusskabel-Leuchtmittel-schwarz/dp/B014WL12Y0/ref=sr_1_5?crid=2UGYEBPRCJ60P&amp;keywords=steckdosenkabel+mit+schalter&amp;qid=1707167397&amp;sprefix=steckdosenkabel+mit+s%2Caps%2C93&amp;sr=8-5" rel="nofollow noopener">1x power cable</a> fitting for your country, and some CA glue. How to assemble: Attach the endpiece to the banana; you can use a piece of 1.75mm filament as a center point.<figure class="image image_resized" style="width: 47.65%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_4ceaa8f473dc5.jpg"></figure>Screw the lamp socket to the lamp plate.<figure class="image image_resized" style="width: 47.59%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_473e88e09d946.jpg"></figure>Pull the power cable through the banana and attach it to the lamp socket, I used some Wago clamps for it, but there are other ways that work just as well.<figure class="image image_resized" style="width: 46.85%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_7650c623ef73c.jpg"></figure>Fit everything in the banana, once it sits well, fix it in place with CA glue.<figure class="image image_resized" style="width: 47.22%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_c93b2c7abacd3.jpg"></figure>Put the lampshade on, don&#39;t glue it so you can change the lightbulb if needed.<figure class="image image_resized" style="width: 46.77%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_34b75c7f0d046.jpg"></figure>Put the shell over it, make sure it is aligned so that the banana sits nice and flush on the ground, then glue it in place.<figure class="image image_resized" style="width: 46.3%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-02-05_d66fd87002c9c.jpg"></figure> 🍌Enjoy your glowing banana!🍌  You may also like:&nbsp;<figure class="table" style="width: 98.39%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-06-04_fcceb05d8801.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/447981#profileId-354736" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173245/design/2024-05-01_87983a1115de6.jpg"></a><figcaption>🐷Minecraft Animal Farm Pack🐮</figcaption></figure></td></tr></tbody></table></figure>

Peeled Banana Lamp

Decoration

SavageLau

<h2>If you want a commercial license, check out my bio and get it from Patreon.</h2><h2>Personal use only.</h2>&nbsp;This model is design for MakerWorld light contest (2/5). Complete free version is only available on here Makerworld. <h3>Many people have contacted me said they willing to pay for the model. Other platform product manager reach and out said I could use their platform and selling this design for some money, but I have decided to keep it here for free for now. So there will be more people could enjoying it :) So show me your finshed print, I would like to see it. </h3><h3> Anywhere else you see this model upload is Unauthorized (please notify me and report them), beside my own account (SavageLau). </h3>&nbsp;<h2>If you would like purchase LED light needed for this design and filament from Bambu Lab Offical website: Affiliate link is below, so I can get some commission to support my future work. </h2><h2><a target="_blank" href="https://shrsl.com/4h4np" rel="nofollow noopener">https://shrsl.com/4h4np</a> </h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-03-23_4ad27b7082fe3.png"></figure><h2>Filaments that I use for this project: (Bambu Lab Offical website:)</h2><h2><a target="_blank" href="https://shrsl.com/4h4ns" rel="nofollow noopener">https://shrsl.com/4h4ns</a> </h2>&nbsp;&nbsp;&nbsp;<h2>You may also like this design:</h2>PeaShooter Lamp Kit 001. <a target="_blank" href="https://makerworld.com/en/models/174475#profileId-191833" rel="nofollow noopener">https://makerworld.com/en/models/174475#profileId-191833</a> &nbsp;&nbsp;&nbsp;My boss saw some Bellsprout light the other day and she want me to design one. I have one LED Lamp kit come with my a1mini and sitting for a while. So why not turning it into what she want. So the design started adpot the lamp kit into Bellsprout.I found this pic on Google, based on the posture and proportion started deisng.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_bc131748fd272.png"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_33679f29d502a.png"></figure><h2>Update: </h2><h3>2/2/2024. A new profile was made for a1mini. Increased infill/walls on base and body part. </h3>Model main body have been reduced in size inorder to meet the build plate size for a1mini with muti-color prints. &nbsp;<a target="_blank" href="https://makerworld.com/en/u/2010665163" rel="nofollow noopener">@Sascha2202</a> feedback it is a bit hard to keep banlance. Weight increased on printing profile by adding more infill and walls. Weight for that part from 160g to 202g, lowered center of gravity. Consider head is around 40g + led weight, it should do well now. <h3>2/1/2024. Joints redesigned. </h3>Improved joints firction load, strength, tolerancing. New turning angle sets around 13.5 degrees max for each joints. <figure class="image image_resized" style="width:36.72%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_d00693a8b7acb.png"></figure>“Head” part fit and finish improving. <h3>Revisions and Tests today:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_ffe7e41994dec.png"></figure>&nbsp;<h2>Before you print(Important!):</h2>Run the joint test print first with the filament you are going to use for joints and body, before you doing the full print! This is important. Depend on filaments you use for the joint parts, there will be sinkage rate difference, and firction load on joint will be different.&nbsp;I put very tight tolerancing on design, but it may not work as intended when you printing with your filaments, so run the test and confirm joints is very tight to each other. Other wise You will not get the desired result.&nbsp;&nbsp;Joints with other parts are standard size. There is one “Tight” profile for joints. There are two types of joint, regular and with wire clip one. You will need to print total of 12 or above (maybe less than 15) to get good proportion. &nbsp;Joints designed best work with 4 wall layers, and 10% to 20% infill, adding more infill will not improve the strength, will only leading part failure during assembly. &nbsp;<h2>Hard ware:</h2>This design require Lamp LED Kit 001 from Bambu Lab. All other parts are printable. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_bca061fd80f1d.png"></figure>&nbsp;<h2>Post work:</h2>Removing brims from all parts, when you remove brim from joints part, confirm it is fully removed. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_dec1b2c670225.gif"></figure><h2>Assembly:</h2>Refer these gif image. Joints is a bit hard to push in, refer how I do it, holding the bottom part with you fingure, it will reduce the change of failure. &nbsp;Joints:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_5c978e23e8634.gif"></figure><figure class="image image_resized" style="width:51.25%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9f2e463b2d8a6.gif"></figure>Fully assembly:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9a975d341b61f.gif"></figure>&nbsp;&nbsp;&nbsp;<h2>Design:</h2>Lamp kit is 60mm dia, 8mm thickness. based on that dims and make rough draft to evaluate the overall size.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_34bf66e6b20e5.png"></figure>&nbsp;Working on some parts, and integrate them in the end.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_4880a9ab2336a.png"></figure>&nbsp;I started with wanting ball joint on the head, so it will able to turn angles. End up why not to have more ball joints on the body.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_b08f0ea2e5ee9.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ec7f991cbaa.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ed16d7dd498.png"></figure>&nbsp;Ball joints is pain in the axx to work with. I want it to have a lot of friction load in normal condition. so the outter shell shall have very small tolerance to the ball or even smaller. Ended spending a lot of time try in truth to testing out different tolerances and make design revisions.Still not perfect, but it work for this application. You gain a lot of DOF, but it is a bit brittle, depends on your materials.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_153933e0ba5bb.png"></figure><h2>Revisions and tests:</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_641c974fd0d58.png"></figure>

BellSprout Lamp LED Kit 001

Video Games

Soap_Warrior

这是一把香蕉长刀，他与我之前发布的香蕉爪刀原理和形状相似，安装需要使用直径10mm，厚度2mm的圆柱形磁铁。打印不需要支撑，没有AMS的A1mini也能打印，banananana！！！This is a banana long knife, it is similar to the principle and shape of the banana claw knife I posted before, and the installation requires the use of a cylindrical magnet with a diameter of 10mm and a thickness of 2mm. Printing does not require support, and the A1mini can print without AMS, banananana!!!<figure class="image image_resized" style="width:42.59%;"><img src="https://makerworld.bblmw.com/makerworld/draft/793616/2024-03-31_7a7dec75d8f44.gif"></figure>安装教程：与我之前发布的香蕉爪刀安装过程一致。可参考：<a target="_blank" href="https://makerworld.com/zh/models/400018#profileId-301518" rel="nofollow noopener">香蕉爪刀-Banana claw knife 来自 Soap_Warrior - MakerWorld</a>（偷个懒）Installation Tutorial: Consistent with the Banana Claw Knife installation process I posted earlier. See also:<a target="_blank" href="https://makerworld.com/zh/models/400018#profileId-301518" rel="nofollow noopener">香蕉爪刀-Banana claw knife 来自 Soap_Warrior - MakerWorld</a>&nbsp;