Mitsuyoshi

maCyo42

<p><strong>It&#39;s done!!!</strong> All Parts printed and assembled! I started the Riser V2 early December and changed the last Parts yesterday. There&#39;s a lot of work in this design, so many small and big changes. Today i will start to Release the first completed picture of the Riser V2 and the Profiles of the Mainbodies. As you later can see i&#39;ve seperated some Parts so that you can play around with Step Files for your own Design Fronts.</p><p>&nbsp;</p><h2>Should I print the Riser V1 or V2? Here are the differences.</h2><ol><li>There are 2 Versions of the V1. The Standard is for 8mm Lightstrips and the 12mm Edition for 12mm Lightstrip and additionaly you can fix the Lightstrip with Cable ties.<br>V2 combines the Features of both V1 Riser in this Case.<br><strong>I received a lot questions: Will 12mm Lightstrips fit? It can but that is not sure. It not depends only on the width. The stiffness is one big issue for the curves. Try it i cannot guarantee! There are different lightstrips on the market.</strong></li><li>V2 is tuned more for function than design. There are additionaly Connectors for Accessories like Tools.</li><li>Early December i began to work on V2. My intention was the big change in the Anti Glare Feature and the Connectors.<br>But meanwhile there where some critics on the V1. Some Makers reported a bad fitting of their Top Glas. To much loose in the Spoolholder fitting and so on. So the logical consequence was to rework many things on V2.</li><li>The Modders. I had so many Mails and Msg… can you please add Hexagons insted of Holes and so on. Because of this i reworked the Covers and seperated them for the Modders. You can now easily create your own designs on the most seen Parts of the Riser.</li><li>The printability. Puh i don´t know how to begin exactly. Makerworld makes a lot very easy. But a project like this is not easy. It´s big, it can fail as any other Print… it can fail! But you can do a lot that the chance that it will fail is very small. You have to know your printer, your Filament, your Buildplate… The condition is not the same as i have. But it´s quite easy to begin if you have a predefined Profile.<br>But it´s not a Microwave, it´s a 3D-Printer, a popular and wonderfull Printer. It makes a lot easier and it´s the by far best for consumer on the marked… and nevertheless you have to know what you do. Please keep in mind!<br>I reworked a lot to make it even easier. Less Supports (less filament usage is everytime the best optimization!)<br>Tuned Overhangs especially on the back which is on the Print surface while printing Part 3 and 4. and many more changes</li></ol><p>happy printing</p><h2>Features Description</h2><h4>Accessories Port<br><span style="background-color: rgb(255,255,255); color: rgb(89,89,89); font-size: 14px">New second Accessories Connector Port. The Port is redesigned an optimized. Accessories fits tighter. The Spoolholder on V1 was a bit to loose.</span></h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_d57fe6c9f6869.png"></figure><h4>New seperated Drawer Front Cover and Handle</h4><p>With the new separated Drawer Front you can create easily your own Designs and Text on it and print it upside down for best looking Surface. <strong>(STEP File of the Cover included)</strong><br>The new Handle locks both Parts (Drawer and Cover) together. No Glue needed!</p><p>&nbsp;</p><p><i><strong><u>Compatible Inserts for the Drawer</u></strong></i><br><a target="_blank" href="https://makerworld.com/de/models/44128#profileId-45567" rel="nofollow noopener">Original Inserts &amp; Dividers</a> by <a target="_blank" href="https://makerworld.com/de/u/1818851574" rel="nofollow noopener"><strong>tomtom5893</strong></a></p><p><a target="_blank" href="https://makerworld.com/de/models/50855#profileId-52695" rel="nofollow noopener">CHT Nozzle Holder</a> by <a target="_blank" href="https://makerworld.com/de/u/2301853465" rel="nofollow noopener"><strong>kylecasey4</strong></a></p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_e7570c3e6befc.png"></figure><h4>New P1S Front Dash Parts with separated Cover for leave Blank or your own Design</h4><p>In the Standard V2 you have a dummy for the Slot where you can mod different things like a light Switch.<br>The Slot for the MicroSD Card is now protected with a Cover. If you press on the lower Part of the Cover it opens. Yes it´s tricky to get the Card out, but how often you want to get it out… i recommend to use a tweezer or something else.<br>The Covers of Part 5 &amp; 6 is now separated too. You can add your own designs and print it upside down. <strong>(STEP Files of the Covers included)</strong></p><h4><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_a2e0b276312d6.png"><br>Light Strip integration and Anti Glare</h4><p>The Lightstrip integration is fully redesigned and now combines “<i>V1 Standard</i>” and “<i>V1 12mm Edition</i>” in one sleak Design.<br>You now have a lot of cable tie position to safe your Printer from falling Lightstrip!</p><ul><li><strong>I strongly recommend COB LED Light Strip with 8mm width. </strong>Length 2m and cutable.</li><li>Yes you can also use 10mm or 12mm BUT beware. Most 12mm LED Strip are so stiff that it´s a mess to integrate them.</li></ul><p>The Anti Glare Feature moved from the Mainbodies to the TPU Gasket Parts because of collisions with the PTFE Tube while printing big Parts.<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-17_88977cc660f9.png"></p><p>Why more Light? Do i need more Light? YES i think so!<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-17_7662231c60b07.png"></p><h4>The Toolholder Connector</h4><p>With this Connector you can add whatever you want to the Riser. In the First step i added the Connector for my <a target="_blank" href="https://makerworld.com/en/models/28768#profileId-25133" rel="nofollow noopener">P1S Tools Model (Get it here on Makerworld)</a>.<br>The Toolholder Connector is provided as a Step File as well. With this the Modding Community is able to connect whatever they want.<br>There are 6 Connector Ports 4 of this. 2 on the Left Side and 2 on the Right Side. There are 2 more Connector Ports on the Back in a different design. <strong>(STEP File of the Toolholder Connector included)</strong></p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-18_6005761ec053d.png"></figure><p>You can also attach a Spoolholder. <a target="_blank" href="https://makerworld.com/en/models/53455#profileId-55205" rel="nofollow noopener">Get my Version with Bearings here</a></p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-18_841008088edb2.png"></figure><p>The “Back Connector” is finally released. Unleash your modding ideas, perhaps for an ESP32 case that can be attached to the back?<br>Use one, two or even all 4 connectors for your modding idea.<br><strong>(STEP File of the Back Connector included)</strong></p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-02-23_e06df92819799.jpg"></figure><h4>Where to find the &#34;RAW Files&#34; on Makerworld? e.g. Back Connector …</h4><p>So there are 2 Options. One you can see in the folowing picture as provided by the designer you can find the Parts under “Download STL” else </p><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_12c13e3925103.png"></figure><h4>Asssembling Guide</h4><ol><li>Push Part 2 on Part 1<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_0b3ee7ecae28a.png"></li><li>Push carefully Part 3 on Part 4<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_719957f53c68.png"></li><li>Then push carefully both Parts 3 &amp; 4 together from the Top to the Bottom in Part 1 &amp; 2<br><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_1d6c733360ed3.png"></li><li>tba</li></ol>

Maintenance