Mission

Jackalolz

<h3>Illuminate your base, and stay safe!</h3>Say hello to the second instalment of my Minecraft lamp series; The LED Restone Lamp. This bright model is at an 8x scale with support for the LED Lamp Kit found in the Bambu store and supports for an LED strip with a controller.&nbsp;This is a simple two-tone build and is printable on the A1 Mini. On larger printers, it is achievable to print this model in fewer total prints. This model consists of a transparent shell surrounded by 6 side plates pushing together with their joins. All press joins have a tolerance of 0.1mm which I was able to achieve with my A1. No screws or glue are required during construction. If you want to have the lamp attached upside down or horizontally I would consider glue.<h4>Materials &amp; Filament:</h4>For the model seen above I&#39;ve used;<ul><li>PLA Bronze for the surround frame</li><li>PTEG Transparent for the lamp shell. (PLA Transparent can be used, keep aware of heat when running WLED illumination)</li></ul>The frames and WLED insert were printed using the 0.4 nozzle, however, the PTEG shell was printed at 0.6 nozzle. PTEG transparent can be printed with a smaller nozzle, seek Bambu Labs tips on printing PTEG transparent filament. I have not tested printing the shell in generic PLA, however after running a transparent test, I can&#39;t see it working with anything that isn&#39;t transparent.<h4>Construction:</h4><figure class="image image_resized" style="width: 70.11%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_cb23c501ebdd8.png"></figure><ol><li>Print all frame plates. Print the “front/back” plate and “left/right” plate twice. In total, you should have 6 frame prints. </li><li>Insert your light source into the base plate</li><li>Place your front/left/back/right plates into the base following this order listed. The back of the model has the cable guide in the base.</li><li>Insert transparent shell</li><li>Enclose the shell and join the sides together with the final roof frame</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_d3df4b47cac7d.gif"></figure><h3>WLED Examples</h3><figure class="image image_resized" style="width: 50.1%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_a5a13dd01ae84.png"></figure>This is the insert that is printable for the WLED route. It is hollowed out with enough space to fit a microcontroller and any necessary wiring. For my design, I&#39;ve used a 12v LED strip that I have glued spirally from top to bottom. For the brains, I&#39;ve used an EPS32 controller running WLED. There are a bunch of tutorials on <a target="_blank" href="https://www.youtube.com/results?search_query=WLED+setup" rel="nofollow noopener">Youtube</a> on how to use WLED from installation to wiring. Lastly is a step-down DC to DC Buck module to send the ESP32 3.3v. If you need further assistance feel free to comment and I will post my setup.&nbsp;<figure class="image image_resized" style="width: 60%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_951e7d98ea3f6.png"></figure>&nbsp;PLEASE REMEMBER: HEAT WARNINGLED Strip can become hot when on for large durations and the default beacon shell keeps all heat trapped inside the enclosure. Please be cautious in filament selection and consider tougher materials such as PTEG and above. I recommend using the second print plate on the shell print file with the added Minecraft sword air vent to expel heat. <figure class="image image_resized" style="width: 80.1%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_cc4ba071b1fc1.png"></figure><figure class="image image_resized" style="width: 80.82%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000489519/design/2024-06-09_d7f4b7e7b63e2.png"></figure><h4>Congratulations &amp; Enjoy!</h4>It&#39;s that easy! Please rate, comment and enjoy your beacon. Happy mining!

Minecraft Restone Lamp (LED Lamp Kit 001 & WLED)

DanTup

Update: I have published a redesigned version of this model that may be less likely to come apart and where the middle part will spin more freely: <a target="_blank" href="https://makerworld.com/en/models/479274#profileId-390597" rel="nofollow noopener">https://makerworld.com/en/models/479274#profileId-390597</a>&nbsp;A small heart keyring with rotating inner sections.&nbsp;&nbsp;

Rotating Heart Keyrings v1

饰品

DKdevt

A fun toy gun that launches discs with a magazine for 15 discs of 20mm.It shoots with great speed and accuracy at short distances.&nbsp;<ul><li>Completely printable design. </li><li>No need for extra screws or glue. </li><li>Just 2 elastic bands for the push mechanism of the magazine and the trigger striker.</li><li>Use a pair of fine-tipped pliers to help you with the assembly of the rubber bands. </li><li>Skills are required for assembling the mini gun. </li><li>The design consists of multiple parts with very tight tolerances. </li><li>Use PTFE(Teflon) grease for perfect operation and increase performance.</li><li>Please perform a filament flow calibration! </li><li>Use previously dehydrated and high-quality filaments.</li></ul>&nbsp;Check the new Power pack to increase shooting distance and accuracy with reinforced toroidal bullets:https://makerworld.com/en/models/486278#profileId-398995You can print extra magazines and easily reload your disc launcher. Enjoy :P&nbsp;Consider supporting my work with a &#34;Boost&#34;🚀 and a &#34;Like&#34;👍🏻 so I can continue creating refined designs to share for free with everyone.🤓

Disc Launcher Semi Auto Rapid Fire Print-in-Place 

make

This is a retractable car phone holder that can be used to secure the phone. Remember, the other tray is fixed with screws on the outside. Please do not mix them up, otherwise the expected effect will not be achieved.

灯

饰品

GUN

支架