Caramel

MNeilson

6&#34; long mixing paddle for epoxy resin and other 2 part blends. 6&#34; long, with a ¼&#34; drive that fits a drill or impact driver. Each paddle only costs less than 20 cents to print! I found the reusable ones to be annoying because they are hard to clean. I recommend printing at least 2 at a time to allow for cooling. Works well on my P1S, but parts like these would be difficult to print on a bed slinger.  For a larger version, see my other model here! https://makerworld.com/en/models/423343?from=search#profileId-326520

Epoxy Resin/Silicone Paddle for Drill

Bricolage

sipura

Hello everyone,&nbsp;UPDATE 10/03/2024New upper inner tray profile added. Easy to print. To assemble you need 4pcs magnets 8x1,5mm and 2pcs filaments for hinges. &nbsp;There were a lot of questions and a lot of you asked for a bigger case, so we decided to make it.This is the 3rd case we made and the largest, the XL model  The difference from the previous models is that we changed the design of the clips, and the hinges are 0.5mm thicker than the first standard, we think that&#39;s a sweet spot.&nbsp;Also, the inner boxes are larger and are modular. You can remove the partitions, and increase or decrease the inner box according to your needs.&nbsp;Big advantage is that the inner boxes are compatible with those of the smaller models, which you can see in the last two pictures.&nbsp;Simple print without supportAll parts are completely printed with PLA, only the gasket needs to be printed with TPU in order to close smooth and seal nicely.&nbsp;To assemble it, you need:6pcs M3 nuts2 pcs of screws M3x32mm3pcs of screws M3x20mm&nbsp;I hope you like it, and enjoy printing and using this useful case.Feel free to put your pictures of printed models in comments. :D&nbsp;Also, if you need some custom accessories for all our models, you can contact us on our patreon page which is in bio.&nbsp;Enjoy printing :D

Utility XL - case

Makefy

It's planting season!<blockquote> TIP: Use a cotton pad in the bottom of each pot to keep the dirt from spilling into the bottom tray! &nbsp;</blockquote>&nbsp;This is a new version of a design I made and tested last season. Turned out to work great.The assembly consists of the following parts: Bottom Tray: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_52bc4f5b6a06.png"> This is the main part which holds water. It has guides for the pots and slots for the connecting beams. It should have enough solid bottom layers to avoid any infill. Just to make sure it's completly watertight.&nbsp;Connecting Beam: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_ab0b1e814f06f.png"> This is the part that supports the top plate. You will need 4 of these &nbsp;Pot: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_fb839ee86539c.png"> This is the pot itself. It consists of two parts that snap together. PLA seems to hold up pretty good for this part, but PETG or ABS might be a better choice. Top Plate: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_df2f64c41e23d.png"> This parts connects to the bottom tray with the four beams and holds the pots Greenhouse Dome: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_66dfe67204146.png"> This is a clear cover which provides a warm and humid environment for the seedlings. This part is provided in a separate print profile and should be printed in clear PETG or PC: — OPTIONAL --- Dirt Funnel: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_5f6384536a117.png"> The funnel makes it easier to fill the pots with dirt The Pestle: <img src="https://makerworld.bblmw.com/makerworld/draft/678120/2024-03-09_2ac2891fe5821.png"> Use this to gently pack the dirt.

Self Watering Seed Starter/Planter with Splittable Pots and Greenhouse Dome

Garden

ali_264

Hey Everyone! I really loved the design of the <a target="_blank" href="https://www.youtube.com/watch?v=gcaREZGfyDQ&t=1s&ab_channel=Prusa3DbyJosefPrusa" rel="nofollow noopener">Prusacaster</a> done by Mikolas Zuza of the Prusa team, but the kit they linked was very expensive to ship to the US. I remodeled my own version based off this <a target="_blank" href="https://www.amazon.com/dp/B08TBZZN3K?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">amazon DIY Stratocaster Kit</a>. All the parts are included in the kit and you only need to print the 5 parts. &nbsp;Printer: Bambu Lab P1P w/ .4mm hardened steel nozzle&nbsp;Filament: Bambu PLA-CF and Elegoo PLA+** I only used the PLA-CF because I had it from the 1 year anniversary gift, I've seen people do similar designs out of normal PLA and have no issues &nbsp;Print Settings:Body (very structural and needs to be much stronger)-.2mm layer height-8 Wall Loops-5 Top and Bottom Shell Layers-25% Gyroid infill-Normal(auto) Support-.2 mm Top and Bottom Z distance for support (under Advanced)-Mouse Ear Brim&nbsp;All other parts-.2mm layer height-3 Wall Loops-3 Top and Bottom Shell Layers-10% Gyroid infill-Normal(auto) Support-.2 mm Top and Bottom Z distance for support (under Advanced)-Mouse Ear Brim&nbsp;Some of the parts are close to maxing out the build plate, but just keep rotating the parts. They all fit on a 256x256 mm build plate.&nbsp;Assembly:After sanding the faces the would be glued together with a fine grit sandpaper, I glued the parts together using standard Superglue. I recommend aligning all the parts with the front flush to a flat surface before gluing (learn from my mistakes). For the screws that hold the pick guard and cable connector on, I drilled pilot holes that aligned with the existing holes on the parts and screwed them on. For the vast majority of the assembly I just followed the guide that was provided in the kit.&nbsp;Results:Overall, I am happy with the results I got! It plays as you would expect any non-3D printed guitar to play. It is by no means an amazing guitar, but was a very fun build and really rewarding to play it afterwards! I have included the STL's and STEP files if you are looking to do any modifications to the design.

Printacaster

Guitar Stuff

reddadsteve

Kermit the Frog, a Muppet character by Jim Henson.Kermit serves as the straight man protagonist of numerous Muppet productions, most notably Sesame Street and The Muppet Show, as well as in other television series, films, specials, and public service announcements through the years.No supports are required. If you have the proper filament colors, no painting is needed.The assembled model is 140mm tall.Enjoy!<h3>Print instructions</h3>Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10%Notes: Refer to the notes below for helpful printing and assembly instructions.<hr/>Building the Model Colors (there are no multiple printed pieces)Black: eye_black_right eye_black_left mouth_blackRed: mouth_top mouth_bottomGreen: head bodyWhite: eye_white_right eye_white_leftYellow: ruffPink: tongue<hr/>Printing and assembly tipsPrinting tips 1-No supports are required. and I printed all the pieces without a brim or raft.2-The parts should fit nicely when printed cleanly or with a slight first layer squish... Assembly tips: 1-The left/right black eye pieces are interchangeable. I post all my parts exactly as modeled, even if they are duplicated.2-Position the ruff on the body, noting that the ruff should sit very comfortable over the shoulders.3-**Important: the mouth_top part is printed flat but the roof of the mouth is curved. Glue the mouth_bottom to the head first, then try and bend/flex the mouth_top piece so it fits the roof of the mouth a bit. You may need to hold this piece up while the glue is setting.4-The tongue fits into a slight groove in the mouth_bottom piece. The mouth_black piece should be simply centered left/right and placed as far back on the mouth_top piece. The points of the mouth_black piece should point forward. I wanted to keep the mouth_top piece as thin and flexible as possible, so no indent was added for the mouth_black piece5-Refer to the assembly diagram for putting the model together. The model is meant to be glued.

Kermit

Cartoon

OldSpice3d

Star Wars logo led lightbox&nbsp;Everything properly setup in .3mf files&nbsp;Enjoy :D

Star Wars Lightbox LED Lamp

Star Wars

miqu

Introducing the HiveLight, a straightforward yet captivating lighting project leveraging the Bambu Lab LED Lamp Kit 001. This version is designed for simplicity and ease of use, appealing to anyone looking for a hassle-free lighting solution.&nbsp;For enthusiasts seeking an elevated experience, the advanced WLED HiveLight variant awaits <a target="_blank" href="https://makerworld.com/en/models/164042#profileId-180069" rel="nofollow noopener">here</a>. This audioreactive iteration features a touch sensor for convenient on/off control. Leveraging the capabilities of WLED, it delivers enhanced customization and smart functionality for a personalized lighting experience&nbsp;

HiveLight for LED lamp kit 001

Lampe

KefmaDE

"4 IN A ROW" is a strategic two-player board game, also known as "Connect Four." The game board consists of six rows and seven columns, where players take turns dropping their tokens. The objective is to be the first to connect four of one's own tokens horizontally, vertically, or diagonally. Players must strategically plan their moves to either create their own four-in-a-row or simultaneously block the opponent. I designed the game in a compact box, making it convenient for on-the-go or travel gaming.

4 IN A ROW - Travel Edition

Game

Thor3D

Hi…&nbsp;This is a Ikea Skadis (and all accessorys you can find here) compatible Plate for mounting on the side of a Bambu X1C (P1 should work aswell).&nbsp;You need two 10x4mm magnets to keep the plate in position. It's designed to lay on the upper corner but it's still possible to open the lid.&nbsp;The plate is 240x180mm. Just add Holders as you need. Plier, allen keys, whatever… There are holder for everything you can imagine… the whole Skadis Universum is usable!&nbsp;If you got a make please show it. :)&nbsp;*I personally prefer double-sided duct tape put it's up to you if you want to use the magnets. Be shure to get powerful magnets, the first i got were to weak. :). If you want to use duct-tape just print two of the magnet replacement inserts (uploaded it to the raw files). For the 2 Color Version i needed a little trick to get white Brim! If you only load 2 Colors the Brim is green :( I used White/Green/White in my AMS and so i tricked the system. Green Brim on a white plate leaves some rest color… I would say it's a Slicer Error… Thanks!

BambuLab magnetic Skadis Side Plate for Tools

Bambu Lab

Jonas_H

If you like plants, lights and 3D printing then this could be a nice project for you.This print is a plant pot that combines all these things together in one thing - a glowing plant pot.&nbsp;The special thing is that you can change the inner look from the plant pot when you cahnge the type and density of the infill pattern. You can review these changes in the slicer when you temprarely set the wall loops to zero. In the uploaded print profile you can find the variants that are pictured in the photo section.&nbsp;As a light strip I have used these 10m long ones from Amazon: <a target="_blank" href="https://amzn.to/42NRtFl" rel="nofollow noopener">https://amzn.to/42NRtFl</a> (this is an Affiliate Link. When you order with this Link I get a small provision and that helps to support my work)&nbsp;As filament I have used a transparent PETG Filament for the part A and matte black PLA Filament for part B and C.&nbsp;The assembly is pretty straight forward.The first step is to insert the whole LED strip through the hole onto the plant pot.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/585393/2024-02-18_e94e7cce8eb11.png">&nbsp;In the next step you can fix the end of the LED strip with some tape to the inner plant pot (part B). Now simply roll on the whole LED Strip to the inner plant pot.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/585393/2024-02-18_f7d992e3c29dd8.png">&nbsp;When this is done fix the other end to the inner plant pot with some tape. Now you can insert the inner plant pot into the outer part. If you want you can glue the two parts together.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/585393/2024-02-18_6193c0b3c5fff8.png">&nbsp;Now you are finished. If you have any questions or improvemnt sugestions please leave them in the comments. I would be more then happy to answer them.&nbsp;Happy printing :)