Mehness

chameko小廢物電波塔

<blockquote>12/06 After many tests, I successfully found out the cause of the assembly problems reported by some users, and modified the side panel file "AMS Dry Box-SW_v2".NOTE!I Designed this model not only for ams, I also used it in the vacuum bag that holds the filament, so I needed tight tolerances to make the box strong enough. The tolerance is 0.3mm, please be sure to confirm before printing this model.</blockquote>Open the side lid and pour about 60g of silica.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_92a6870d48198.jpeg">&nbsp;There is a buckle design on the top, please make sure it is buckled correctly when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_2f71bc9cf33e9.png">&nbsp;&nbsp;The front and back of the V2 version have relaxed tolerances in most areas, making it easier to install. I kept the last small area because without this part, you might get the box and slide it open like in the second picture, resulting in a mess.Please be careful not to install it in the wrong direction when installing.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_fcf2db2bab532.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_210d78c4699ec.jpeg">&nbsp;If you have trouble assembling them, try using a heavy object to knock them into the correct position.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_e0f13f6121362.jpeg">&nbsp;As for why I used this complex design, it was because I considered that he had to withstand several kilograms of impact from the filament, so I wanted to distribute the force as equally as possible to each part.<img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-25_90a605e9c843e.png"> <blockquote>Also I have a beautiful model related to AMS! Don’t miss it!</blockquote><figure class="image image_resized image-style-side" style="width:56.75%;"><a href="https://makerworld.com/zh/models/99476#profileId-106044" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/306465/2023-12-23_3d850a0169288.jpg"></a></figure>Do you always find the AMS feeder difficult to press? Are the models on the Internet very difficult to install? I have improved and carefully designed this model. Please be sure to try it!(click on the image to go to the page!)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<blockquote>----------中文解說----------</blockquote>打開側蓋後約可倒入60g的乾燥劑. 上方具有卡扣設計,安裝時請確認有正確的扣上.&nbsp;V2版本的正面與背面放開了大部分區域的公差,使其較容易安裝. 我保留了最後一小區域,因為沒有這個部分的話,你可能再拿取盒子時像第二張圖一樣滑開,導致一團糟. 安裝時請注意不要裝錯方向.&nbsp;如果你在組裝上遇到了困難,可以嘗試使用重物敲擊他們使其安裝至正確的位置. 至於為什麼使用這種複雜的設計,是因為我考慮到他必須承受數公斤來自線材的撞擊,因此我想盡可能地讓力量平均分攤到每個部分.

AMS Silica Gel Box[V2]

Bambu X1C upgrades

vandragon_de

<h2>Summary</h2><h3>My first bathtub boat</h3>so that young and old captains can play in their own bathtub&nbsp;In the file the ship is 10cm (3.93in) long. But my prints are only 8,5cm (3.34in) long. So I printed the ship about 13 percent smaller.&nbsp;&nbsp;Even if my boats are not benchmarks (benchy), you can use them for quality control.&nbsp;<h3> </h3>

Bambu X1C upgrades

Maximilian