Maddin31

Tibberz

This is a test model to find the best flowrate for ironing with a specific filament. Standard setting is set to 10% flow, and that's not enough for some filaments. Print my 3mf and change filament for the part and see directly on the part when its finished what flowrate is best. Feel free to modify if you want.It's just a quick and dirty way to check the best flow.&nbsp;Remember that large prints may need more flow than this test print will tell you because of the small footprint.

Ironing calibration model

Print Profile

jwalker55

Basic vase with a stone type pattern.&nbsp;Included is a filled version for printing in vase mode and a regular version with the inner cavity modeled for regular printing.&nbsp;For printing in vase mode, you'll probably need a lower layer height (0.1-0.15mm) to accommodate some of the small overhangs near the bottom.

Pattern Vase

Vasen 

nyx_nk

Filled Air Jordan 1 model. No internal support needed&nbsp;All models have a PETG support-part interface that allows easy removal of the support, so please use PETG for that purpose. In the absence of PETG, use PLA but this will make it more difficult to remove the support. Same if you are not equipped with AMS: the model will be made entirely of PLA

Nike Air Jordan 1 - CLOSED MESH

Random Decoration

rostap

<h3>Arm mounting system </h3>It is a universal set of holders and arms. You can use this system as a notebook holder, tablet holder, monitor holder, camera or any other device holder or you can have it as a shelf holder.If you print a pair, you can made various tables.You can attach more arms togehter. I made some connecting parts and other accessories. There are no limits to imagination. I made it with increased strength and durability. If you add few perimeters the holders/arms can hold pretty good weight. &nbsp;&nbsp;&nbsp;Small light versionHolders reduced x 0.6 and then adjusted (hole sizes, gaps, etc.)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_ygt4l1gyz0rx.jpg"></figure><h4>Základní informace</h4><figure class="table"><table><tbody><tr><td>&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_1vuk35qftkm3.jpg"></figure>&nbsp;</td><td>&nbsp;You can adjust the angle in ten degrees. Screw and nut fit on both sides. &nbsp;&nbsp;&nbsp;</td></tr><tr><td>You can tight and loose from both sides no matter where the nut is. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_5bbkp2ve4kgr.jpg"></figure></td></tr><tr><td><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_l4f3cs4r4hsf.jpg"></figure></td><td>There are various nuts and screws. Of of them counts with the allen screw (hex bolt) M8x40&nbsp;</td></tr><tr><td>You can also print the crew which can be tight and loose without gear- with the printed hex bolt screw. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_7dyjbvq16pqm.jpg"></figure></td></tr><tr><td><img src="https://media.printables.com/media/prints/165239/rich_content/5d2096ce-0223-4834-ade9-1fd6b3aec194/resize_img_6432.jpg#%7B%22uuid%22%3A%2292583698-0623-4e34-94da-bb853c30ae47%22%2C%22w%22%3A2016%2C%22h%22%3A1512%7D"> <img src="https://media.printables.com/media/prints/165239/rich_content/4dd49cb0-b7a2-4690-8a96-9c03407d2c2e/resize_img_6427.jpg#%7B%22uuid%22%3A%225c571a00-83c6-45bf-a6bb-97f04a44ed33%22%2C%22w%22%3A2016%2C%22h%22%3A1512%7D"></td><td>The holes for key in the screw and two arms have the same size as the holders in Honeycomb storage wall (https://www.printables.com/cs/model/152592-honeycomb-storage-wall). That means that you can hang different accessories on the arms. </td></tr><tr><td>There are various of arms. </td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_bdrw6oh1oh1y.png"></figure></td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_u06b8t58ztlv.jpg"></figure></td><td>ClampI made 3 different types - <ol><li>for the screw M5/M6 mounting spacing for holders 30x30mm</li><li>for the screw M5/M6 mounting spacing for holders 40x40mm</li><li>for the screw M5 mounting spacing for holders 40x40mm</li></ol>&nbsp;</td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_t3u1ipn1agdd.jpg"></figure></td><td>VESA rotating holder - 75mm</td></tr><tr><td>Combination for possitioning along the axis Z<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_7m1sfrwcw20k.jpg"></figure>&nbsp;&nbsp;</td><td>System - high table for tablet holder <img src="https://media.printables.com/media/prints/165239/rich_content/228c6e5e-a2a4-41ce-a79e-962f4006c973/resize_img_6430.jpg#%7B%22uuid%22%3A%22da81a7de-4dd3-453e-96dc-6c179e6bc32e%22%2C%22w%22%3A1512%2C%22h%22%3A2016%7D"></td></tr><tr><td><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_11nh0grq3czm.jpg"></figure></td><td>There are holders for three tablets. Bottom width<ol><li>196 mm</li><li>250 mm</li><li>305 mm</li></ol>screw spacing 30mm</td></tr></tbody></table></figure><h4>Basic arms</h4>The only difference is the grid<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_0qsfmal86eys.png"></figure>&nbsp;<h3>Holders</h3>A few basic handles<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_wjg38olir4sz.png"></figure>&nbsp;<h4> </h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_ej2zf1avpe73.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_2ujybj6hyhzb.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/181205/2023-09-26_3i0br0eesaay.png"></figure>&nbsp;I printed small parts on the Prusa Mini, the arms on the Ender 3.&nbsp;My printing settings<ul><li>material: PETG</li><li>perimeters: 8 and more</li><li>infill : 30% and more</li><li>layer height 0.3 (with nozzle 0.6 layer height 0.4) (screw and nuts only 0.2mm layer height) </li></ul>&nbsp;

Multifunction Arm mounting system

Office Gadgets

ATTV85

PLA of diferent colours 20% infillBase part…….1xParts 1 - 7……3xBox fot tetris without lid <a target="_blank" href="https://makerworld.com/cs/models/98222" rel="nofollow noopener">Tetris balance game box by ATTV85 - MakerWorld</a>Box for tetris with lid <a target="_blank" href="https://makerworld.com/cs/models/102143" rel="nofollow noopener">Box for tetris game with lid by ATTV85 - MakerWorld</a>Dice <a target="_blank" href="https://makerworld.com/cs/models/102146" rel="nofollow noopener">Tatris balance game - dice by ATTV85 - MakerWorld</a>&nbsp;

Tetris balance game

Games 

Satisartes

Cute ball to hold your napkins.dont forget to glue the pieces.

Christmas napkin holder

Christmas

cyanidesugar

Can it do the Kessel Run in 12 parsecs? Who knows?! &nbsp;This is a fairly simple print-in-place Hueforge Hybrid print-in-place piece that combines filament painting methods and traditional 3D printing methods in one singular print. It utilises 4 filament colours, 3 for the Hueforge print, and one for the Millennium Falcon. &nbsp;If you are using the one-click 3MF file on Makerworld, all appropriate settings have been applied to the print. If you are not using the one-click printing method, or are NOT using a Bambu printer, see the print instructions below: &nbsp;Print Instructions: <ol><li>Print the hueforge print (0mm - 2.08mm) at 100% infill.</li><li>The Millennium Falcon portion of the print (2.08mm - 80mm) should be printed at 10% infill, with 3 wall loops, 3 top and bottom surfaces. I used a layer height of 0.16mm.</li><li>You can achieve this by using a layer height modifier in your slicer to modify layers 2.08mm-80mm.</li><li>You do not need any supports for this print. </li><li>I used Burnt Titanium as the background for the print, but you can use any variation of a dark or black colour.</li><li>I used Polymaker's Starlight Mercury for the Millennium Falcon, but you can use any gray or silver variant, or whatever you like!</li></ol>Filament Swaps: &nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.2mm&nbsp;Filaments Used: - PLA Flashforge Burnt Titanium Transmission Distance: 2.5 - (You can use black!) - PLA META Sunlu Teal Transmission Distance: 5.4 - PLA Kingroon White Transmission Distance: 8- PLA Polymaker Starlight Mercury (This is for the Millennium Falcon!)&nbsp;Swap Instructions: - Start with Burnt Titanium - At layer #7 (0.68mm) swap to Teal - At layer #11 (1mm) swap to White- At layer #23 (1.96) swap to Starlight Mercury (this is the Falcon!)&nbsp;The wonderful Millennium Falcon model was sourced from <a target="_blank" href="https://www.printables.com/model/212461-fillenium-malcon-improved" rel="nofollow noopener">here</a> by <a target="_blank" href="https://www.printables.com/@Gareth42_280557" rel="nofollow noopener">Gareth42</a>. If you haven't yet, you should definitely print the standalone model, because it it marvellous! &nbsp;Have fun, and let me know how you go with the print! &nbsp;____________________________________ Commercial License to Sell PrintsIf you want to sell any physical models I have uploaded anywhere, an unrestricted commercial license is available on the $10AUD tier of my <a target="_blank" href="https://patreon.com/cyanidesugar3DP?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=creatorshare_creator&utm_content=join_link" rel="nofollow noopener">Patreon</a>! ____________________________________&nbsp;

Piece of Junk in Space - Hueforge Hybrid Print

Hybrid Print

JamesThePrinter

** Get an early start! Get the <a target="_blank" href="https://makerworld.com/en/models/41177" rel="nofollow noopener">Christmas version</a> now! **&nbsp;&nbsp;Light up different Halloween scenes in this display. A tea light candle is required. The display features a door that opens to allow access to the tea light. Use a section of 1.75mm filament inside the hinge to connect the door to the case. Depending on your printer/setup, this hole may be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.I have included a separate liner. This allows you to print the case in a dark color, but line the inside with a lighter color to allow for more reflection of light outward, making everything brighter.For a complete display, you will need:<ul><li>1x Case</li><li>1x Door</li><li>1x Knob</li><li>1x Snap Ring</li><li>1x Liner - Optional</li><li>1x (minimum) Scene - You can easily remove the snap ring to swap out scenes as desired</li></ul>Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.<h4>Print Settings</h4>No special setting are needed for the display case, door, knob, snap ring and liner. &nbsp;Scenes Print SettingsPrint the scenes with 100% infill. The scenes also require color changes:<ul><li>The top 2 layers should be black</li><li>If there is no moon in the scene, all other layers can be white or clear - both look nice</li><li>If there is a moon in the scene, it will look best if the bottom 2 layers are printed in clear filament<ul><li>All other layers should be white</li><li>All non-black layers could be printed in all white or all clear if one isn't available to you</li></ul></li></ul>&nbsp;<h4>Assembly</h4>Glue the knob into the door. Only a very small amount is needed.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_njhnxlluv3as.png"></figure>Put the door in place and latch it. Use a 20mm piece of 1.75mm filament to connect the 3 sections of the hinge. If the filament goes in very easily, it may be a good idea to heat up the top end of the filament ‘pin’ and press it flat. This will prevent the pin from falling through later on.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_ps9jc73zrxio.png"></figure>Open the door. Insert a scene into the opening (image facing outward). Insert the snap ring behind the scene by gently squeezing and placing it into the groove (see red arrow below).<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_zosx4sj7pb0v.png"></figure>If you are using a liner, slide it inside the case. This may be a tight fit. Go slowly and be sure to slide it in evenly on all sides.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_t3jeg8v9f9hv.png"></figure>Turn on your tea light and close the door.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li><li>GIANTARM Transparent Clear PLA</li></ul>

Halloween Tea Light Display

Dekoration 

Andrew

Doesn't require supports. I printed mine in PLA, but most filaments should work. I wasn't able to find a bin that I liked, so I designed my own. The bins are designed to line up with < 1mm in between to maximize the available space. As the name suggests, the 2x bin is (roughly) twice as large as the 1x bin. 2023-08-27 Update:<ul><li>Added “thin” versions of the bins. These have 1.5mm walls, compared to the 2.5mm walls of the original. The back is still 2.5mm to reduce the chance of damage when inserting and removing from the HSW. </li></ul>

Bin for HSW

Tools

humebeam

Buy Hydra AMS&nbsp;You can now buy the Hydra AMS printed parts and required bolts from MatterHackers at a very affordable price, free US shipping is included. &nbsp;<a target="_blank" href="https://www.matterhackers.com/store/l/hydra-ams-spool-adapter-for-bambu-lab-automatic-material-station" rel="nofollow noopener">Buy Hydra AMS at MatterHackers (United States)</a>&nbsp;It is also available from Australian partner JC-3D:&nbsp;<a target="_blank" href="https://jc3dmelb.com.au/products/hydra-ams-enhanced-for-bambu-lab-ams" rel="nofollow noopener">Buy Hydra AMS at JC-3D (Australia)</a>&nbsp;Hydra AMS has a strict non-commercial license, it can only be sold with licensing through Hume Beam Engineering Solutions.&nbsp;About&nbsp;Download the files then follow the assembly guide a bit down on this page.&nbsp;Optional but recommended files to print:<ul><li><a target="_blank" href="https://www.printables.com/model/455176-hydra-ams-silica-dry-boxes-serial-number-tags" rel="nofollow noopener">Hydra AMS - Silica Dry Boxes / Serial Number Tags</a></li><li><a target="_blank" href="https://www.printables.com/model/530298-hydra-ams-improved-rear-rollers" rel="nofollow noopener">Hydra AMS - Improved Rear Rollers</a></li><li><a target="_blank" href="https://www.printables.com/model/410903-hydra-ams-ptfe-load-buttons" rel="nofollow noopener">PTFE Load Buttons</a> to both save the funnels and improve ergonomics.</li><li><a target="_blank" href="https://www.printables.com/model/402087-adjustable-spool-holder-for-silica-gel-spool-weigh" rel="nofollow noopener">Adjustable Spool Holder for Silica Gel / Spool Weight</a> - Compatible with both Hydra AMS and Bambu Lab AMS.</li></ul>If you download the individual 3MF files in the files section, they are design files only and can be easily printed on any printer / slicer. If you get a warning that they do not come from Bambu Lab just ignore the warning, they were exported directly from my design software.&nbsp;Thanks to the testers for all the support and especially GuyH who has been instrumental.&nbsp;Leave feedback in the comments, cheers!&nbsp;Reviews on YouTube&nbsp;Nero 3D<figure class="media"></figure>MandicReally (Hydra starts around minute 5.40)<figure class="media"></figure>Support&nbsp;All my designs and mods are free to use and remix. They have a non-commercial license. If you enjoy this or any of my other designs you can send me a small donation using the link below. Thanks :)<ul><li><a target="_blank" href="https://www.paypal.me/humebeamengineering" rel="nofollow noopener">https://www.paypal.me/humebeamengineering</a></li></ul>If you prefer Crypto/BTC you can send me a message.&nbsp;If you send a donation be sure to mention Hydra AMS in the comments box and you will be added to the list below.&nbsp;Official Supporters&nbsp;If you have donated $5 or more you will be added to this list as an official thank you from me and you will also be assigned a serial number, the list will be updated as often as possible.&nbsp;You can request a custom serial number if you send a $20 donation or more but please be aware it may take a couple of days before your custom silica box is uploaded as I need to make these manually.&nbsp;If you&#39;ve bought Hydra from one of the authorized resellers you can also request a serial number by submitting a proof of purchase.<ul><li>Hume Beam #0001, Hume Beam #9999, Sven Hausherr #1313, Aaron Gray #1337, FireBall #1725, Trevor Mungovan #2425, Jamie Placzek #4759, 57y10 #8764, Katherine Jones #0666, Bernhard Birkfellner #3101, Guy H #0002, Kevin Pereira #0003, Phill Tran #0004, Bernard Ruf #0005, Justin Altemeier #0006, Remigiusz Kowal #0007, Jerome Grimminck #0008, Anthony Cascone #0009</li><li>Thomas Finzel #0010, Seldon3dPrinting #0011, Dwizzle Roasting #0012, VipCold #0013, Bearded Bucket #0014, Hannes Schäfer #0015, Joseph Korang #0016, Brian Welty #0017, Elmar Wesle #0018, Paul M #0019</li><li>Pippo pewte.ch #0020, Hampus Björk #0021, Martin Watley #0022, Riccardo Sacchetti #0023, James Majors #0024, Raia Gennaro #0025, Christopher Walters #0026, Andrew Shrapnel #0027, Kevin Kent #0028, Aron Gustafson #0029</li><li>Szabó Tibor #0030, Nikhil Ramkarran #0031, Dorothy Rafferty #0032, Charles Ho Fung #0033, Anup Chavda #0034, Dorian Picard #0035, Mark Berg #0036, John Vinson #0037, Robert Martin #0038, Karl Liljeström #0039</li><li>Kurt Althaus #0040, Martin Ziegler #0041, Miguel Contreras #0042, Todd Ferguson #0043, Joseph VonDohlen Jr #0044, Jacob Wine #0045, H. Schittko #0046, Rex Catron #0047, Meatbingo #0048, Barry Kwan #0049</li><li>GnollProblem #0050, Sean Griffiths #0051, Yannick Lory #0052, Bonnie Gulliver #0053, Aki S #0054, Jeremy Rauch #0055, Jim Fano #0056, Jeffery Stephens #0057, Kimberly Booth #0058, Mikael Olsson #0059</li><li>Michael Fetting #0060, James Beck #0061, Christian Bätz #0062, Eric Ridge #0063, Christopher Ondrovic #0064, Stefan Wollmuth #0065, Anthony Soprano #0066, Andreas Riebe #0067, ServTheNet #0068, Alan Kilgore #0069</li><li>Gene Buckle #0070, Phil Harvey #0071, Neal Baggett #0072, Vincent Robel #0073, Zachery Hansen #0074, Matthew Shaw #0075, Scott Marcy #0076, Steven Lionel #0077, John Cardwell #0078, Chris Martin #0079</li><li>Łukasz Szuman #0080, Ron Allison #0081, Bella Art de Nicole #0082, 7iron #0083, JKP Enterprises #0084, Klaus Löhr #0085, Harley Hong #0086, SSI Racing #0087, Chris McLeod #0088, Steven Mohr #0089</li><li>Worked Wood #0090, David Adam #0091, Michal Kowalski #0092, Custom Computer Concepts #0093, Kenneth Ostromek #0094, Stigh Aarstein #0095, Patrick Lavoie #0096, Jeremy Hopke #0097, Erik Johansen #0098, Djundi Karjad #0099</li><li>Jason Litman #0100, Robert Jorgenson #0101, Edward Cartier #0102, Robert Pence #0103, Andres Arrieta #0104, SpriteForge.com #0105, HRtechnik llc #0106, Swen Krauter #0107, Michael Bush #0108, Jordan Newman #0109</li><li>Jared Stymiest #0110, Andreas Klotz #0111, Jordan Joiner #0112, Fred Logue #0113, Gregory Carlton Bouten #0114, Nicholas Daniel #0115, Eric James #0116, Rutger Bogaerds #0117, AtomicFilament #0118, Kevin Clack #0119</li><li>Letusgo2Hell #0120, Gaspard Grosjean #0121, Poppy&#39;s Popcorn Co. Inc. #0122, Tony Herrero #0123, William Aprea #0124, Troy DeJesus #0125, Justin Schuhmann #0126, Belenos #0127, Jack Mettler #0128, Barracuda72 #0129</li><li>Oz_Rob #0130, Ben Silber #0131, fatgeek #0132, Bernt Ahlbäck #0133, Joshua Warren #0134, Thomas Heuer #0135, Thomas Schulz #0136, William Hamilton #0137, Todd Schisler #0138, Phillip Perry #0139</li><li>guruguys #0140, Johannes Cornelissen #0141, Jan Schermer #0142, John Kaminski #0143, SaintHate #0144, Josiah Netherton #0145, Steve Beverley #0146, Boran Li #0147, Jeff ONeil #0148, Joseph Palicke #0149</li><li>Massimiliano Mancin #0150, Patrick Pennza #0151, Donald Lafferty #0152, Big Brook Pond Engineering #0153, Robert Schwinn #0154, Jacob Perez #0155, MIcheal Jeffrey #0156, Brett Corr #0157, Chris Reed #0158, Boris Ott #0159</li><li>John M Murphy Jr #0160, Jose Serrano #0161, Peter Lewis #0162, Christopher Phillips #0163, Tyler Wickline #0164, Integrated Overland #0165, fixumdude #0166, Nic Alkema #0167, Torsten Steckenreiter #0168, Francisco Peebles #0169</li><li>Jens Michlo #0170, Jon Libby #0171, Eric Sutherland #0172, Andrew Poth #0173, Mercury Cubed #0174, Louis Watermeyer #0175, Michael Müller #0176, kirikugo #0177, Markus Lohmann #0178, Stefan Zuegg #0179</li><li>Thomas Kotowski #0180, James Hunt #0181, Marc Schauber #0182, Kenneth Ostromek #0183, Jakub Kanhäuser #0184, Ants-3D #0185, Ronny Stiffel #0186, John Cooley #0187, Christian Noack #0188, Christian Menz #0189</li><li>David Bernabeu #0190, Christopher Mallery #0191, Ralf Ehleiter #0192, Andrew Wickham #0193, David Rouleau #0194, Bruce Milyko #0195, Sean Stoube #0196, Peter Biegel #0197, Dominik Popp #0198, @3dprintkings #0199</li><li>samwiseg0 #0200, Susan Alvarez #0201, Thomas Jameson #0202, Benjamin Achtenberg #0203, Stephen McComas #0204, Volker Alkemper #0205, Daniel Pomierski #0206, Hagen Weigel #0207, Lex Hanna #0208, Dannel Albert #0209</li><li>Jeremy Birdwell #0210, Jeremy Birdwell #0211, Jeremy Birdwell #0212, Jeremy Birdwell #0213</li></ul>Get a Silica Dry Box with your serial number here:&nbsp;<a target="_blank" href="https://www.printables.com/model/455176-hydra-ams-silica-dry-boxes-serial-number-tags" rel="nofollow noopener">Hydra AMS - Silica Dry Boxes / Serial Number Tags</a>&nbsp;Thanks again!&nbsp;If you want to remain anonymous, leave a note with your donation. If I&#39;ve missed your donation let me know.&nbsp;About - Continued&nbsp;Hydra AMS is an enhanced drop-in main body replacement for the Bambu Lab AMS, a multi filament companion to the Bambu Lab X1, X1C and P1P printers. The Bambu Lab AMS internals are used, you just need to move over the parts; the four feeder motors, the rear motor, the front and rear rollers, the RFID boards and the main board as well as the PTFE tubing and cables.The name Hydra is inspired by the mythological creature which grew two new heads as one was cut off, similar to how the AMS&#39;s tend to duplicate if you don&#39;t keep a firm grip of your wallet. I have other designs with names from Greek mythology (<a target="_blank" href="https://www.printables.com/model/130789-icarus-2-qidi-x-max-x-plus-i-mate-x-maker-carriage" rel="nofollow noopener">Icarus</a> / <a target="_blank" href="https://www.printables.com/model/59209-hercules-qidi-x-max-carriage-for-bmg-dragon-e3d-v6" rel="nofollow noopener">Hercules</a>) so I thought it was fitting.Hydra prints completely without supports and no extra parts are required for assembly, it uses dovetail joints for assembly and utilizes the standard AMS outer casing as well as maintains RFID compatibility. 4 x 20 mm cap head M3 bolts is recommended to ensure the three parts interlock and won&#39;t slide apart.&nbsp;The main changes / improvements over the standard AMS are:<ul><li>Increased spool widths, up to 75 mm, meaning most 1 Kg spools will fit.</li><li>Increased spool diameters, up to 202.5 mm diameter spools fit.</li><li>Adjustable spool rollers in four positions for 120 mm to 205 mm diameter spools. Large diameter spools (&gt; 201 mm) require a printed <a target="_blank" href="https://www.printables.com/model/367620-bambu-labs-ams-lid-spacer" rel="nofollow noopener">TPU lid spacer</a> if you want to close the lid, just like the normal AMS.</li><li>AMS feeder / motor mechanism angled five degrees backwards to allow printing of full spools.</li><li><a target="_blank" href="https://www.printables.com/model/410903-hydra-ams-ptfe-load-buttons" rel="nofollow noopener">PTFE Load Buttons</a> to both save the funnels and improve ergonomics (optional, it&#39;s a separate download)</li></ul>BOM - Bill of Materials&nbsp;You can print Hydra AMS in just about any filament you like. However, if you plan on keeping the AMS on top of the printer it&#39;s best to print it in ABS or ASA as the heat from the printer can soften the printed Hydra parts if they are printed in PLA for example. Around 600 g of filament is required at the recommended print settings.&nbsp;I&#39;ve printed most of the test builds in Prusament ASA, PLA and eSUN PLA and ABS+, both brands and filament types work great.&nbsp;Filament<ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DllSAvT" rel="nofollow noopener">eSUN Luminous Green</a></li><li><a target="_blank" href="https://www.prusa3d.com/product/prusament-pla-prusa-galaxy-black-1kg/" rel="nofollow noopener">Prusament Galaxy Black</a></li></ul>Fasteners&nbsp;You need some M3 hex bolts (socket head), I recommend 20 mm but just about anything between 15 and 25 mm should work. If you don&#39;t have any at home it&#39;s best to grab the kit below, it will have everything you need for this build and many more.<ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DFu1g2N" rel="nofollow noopener">1100 pcs M3 Hex Socket Head Cap Kit</a></li></ul>Optional&nbsp;I highly recommend these Nano Coated Helical Extruder Gears from FYSETC, I use them for all my Bambu printers, they&#39;re inexpensive and offer a number of improvements of the stock gears:<ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DDnCqyD" rel="nofollow noopener">Extruder Gear for Bambu X1/P1P/P1S CNC Nano Coating</a></li><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DnKG6yD" rel="nofollow noopener">Extruder Gear for Bambu X1/P1P/P1S CNC Nano Coating (Alternative Source)</a></li></ul>Although not required these PEO/PEI/PEY bed sheets are great, I have most options myself, it gives a quite cool look on the first layer. There are a few shops offering different plates:<ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DCwYeJF" rel="nofollow noopener">Build Plate PEO/PEI/PEY Spring Steel Sheet (Super 3D)</a></li><li><a target="_blank" href="https://s.click.aliexpress.com/e/_Dd4HOjb" rel="nofollow noopener">Build Plate PEO/PEI/PEY Spring Steel Sheet (IdeaFormer)</a></li><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DEJIFPP" rel="nofollow noopener">Build Plate PEO/PEI/PEY Spring Steel Sheet (Juupine)</a></li></ul>The Hex Tools are superb for any 3D printer, I&#39;ve had mine for years. They are particulary useful for the Hydra assembly.<ul><li><a target="_blank" href="https://s.click.aliexpress.com/e/_DF0w38V" rel="nofollow noopener">Hex Tools (1.27 mm - 3.0 mm)</a></li></ul>

Hydra AMS - Enhanced Bambu Lab AMS

MertDizzle

Edit: V2.1 expanded the opening for the screw head clearance Edit: V2.0 I added a new stl with a cut out for the screw head. I have not printed it out or tested it yetEdit: added a short version of the mounting arm to move the spool further back&nbsp;A quick and dirty mesh mixer remix I made combining two models to make the ultimate side spool holder. Needs some polishing. T̶h̶e̶r̶e̶ i̶s̶ a̶ s̶c̶r̶e̶w̶ h̶e̶a̶d̶ o̶n̶ t̶h̶e̶ c̶o̶r̶n̶e̶r̶ o̶f̶ t̶h̶e̶ p̶r̶i̶n̶t̶e̶r̶ t̶h̶a̶t̶ g̶e̶t̶ i̶n̶ t̶h̶e̶ w̶a̶y̶. T̶o̶ m̶a̶k̶e̶ c̶l̶e̶a̶r̶a̶n̶c̶e̶ f̶o̶r̶ t̶h̶i̶s̶ I̶ u̶s̶e̶d̶ a̶ t̶o̶r̶c̶h̶ l̶i̶g̶h̶t̶e̶r̶ o̶n̶ t̶h̶e̶ p̶r̶i̶n̶t̶e̶d̶ p̶a̶r̶t̶ a̶n̶d̶ p̶r̶e̶s̶s̶e̶d̶ i̶t̶ o̶n̶ t̶h̶e̶r̶e̶ u̶s̶i̶n̶g̶ t̶h̶e̶ 2̶ m̶3̶x̶8̶ s̶c̶r̶e̶w̶s̶ t̶o̶ a̶l̶i̶g̶n̶ i̶t̶. I̶ w̶i̶l̶l̶ c̶o̶m̶e̶ b̶a̶c̶k̶ a̶n̶d̶ f̶i̶x̶ t̶h̶i̶s̶ l̶a̶t̶e̶r̶. to prevent the roller from bouncing around when folded up I used some ca glue in the cups that hold the bearings. Another user made a clip to hold the bearings in place without using glue https://makerworld.com/en/models/110906#profileId-118547&nbsp;required materials -608zz bearings (x2) -Bolt M4x45 -Bolt M3x8 (x2)