LuckyMountainMan

Flori_

This is a remix of a model by @EmaKralova(https://makerworld.com/en/models/224716#profileId-242637) I added different size options.The &#39;small&#39; version is the original by @EmaKralova&nbsp;Lengths:Small: ca 140mmMedium: ca 220mmLarge: ca 290mm&nbsp;Advice:The &#39;large&#39; zip tie only fits on the 265mm² build plates diagonally.&nbsp;I recommend printing with TPU&nbsp;If you just want the ‘small’ version, please check out the original design (https://makerworld.com/en/models/224716#profileId-242637)

[Remix] reusable zip tie

S.3D

Buddha, derived from Sanskrit "the Awakened One," refers to beings in Buddhism who achieve Bodhi or "Enlightenment." It's an honorific for Siddhartha Gautama, founder of Buddhism. A Buddha attains purity of mind, perfect wisdom (Prajna), and compassion (Karuna) for all. They've realized Nirvana, escaping Samsara's cycle, though the human body remains mortal. This state is beyond description. Any being can achieve Buddhahood through practice, but it's rare. The next Buddha is Maitreya; past ones include Kashyapa, Kanakamuni, and Dipamkara. Tantric Buddhism has many Buddhas like the transcendent Adibuddhas.

Baby Buddha

Nicole

Qjeezy

Aztec - Mayan calendar, AKA The Sun Stone.&nbsp;This is a loooong print, but it is soooooo worth it. This thing looks awesome. Black filament and some Rub n' Buff makes this masterpiece really pop. You may notice that the thickness is larger on one side of the Sun Stone than the other. This was actually done by mistake but I wound up liking it because it gave it sort of a hand crafted vibe. Perfection is in the eyes of the beholder.&nbsp;&nbsp;Print Recommendations:&nbsp;0.20mm layer height works, but 0.16 helps the details appear slightly smoother. You can go less if you'd like but I personally have not experimented with smaller layer heights. I would not advise higher layer heights. It may work, but you may also lose a lot of the detail.&nbsp;Keep printing speeds on the low side and ensure plenty of infill. There are many fine details that will benefit. This is what I used and what I know works. I started with the default 0.16mm High Quality Print profile and changed the following.- Both initial layer speeds @ 50mm/s.- All other print speeds set to 150mm/s with the exception of outer wall, bridge, and overhang speeds. Leave those at default.- Travel speed set to 300mm/s.- Default acceleration speeds for 0.16mm High Quality profile.- 20% rectilinear infill.&nbsp;If you want to print one that is slightly translucent like the white one in my pictures, use a slightly translucent filament. I used white eSun ePLA-HS. Its not labeled as being translucent, but its got a slight bit of clarity. Just enough I might say to get the effect. I also set the infill to 20% aligned rectilinear.&nbsp;You don't need the AUX fan for this print. To ensure you don't experience warping, turn the aux fan off. If you use Bambu PLA the AUX fan is set to 70% at default. Ensure you turn this off in the filament profile or just turn it off after your print starts if you're printing from the Handy app.&nbsp;Clean your build plate with soap and water and ensure you do not touch the surface with your bare hands. This will help ensure adhesion so you don't lose your print at any point. Feel free to use your favorite adhesion promoter on your build plate for extra assurance.&nbsp;Ensure your filament is dry and calibrated. There are a lot of fine details and tons of travels.&nbsp;You probably can scale this down but just remember the smaller you go, the more details you're going to lose. If you're looking to make a miniature, using a 0.2mm nozzle me be required to retain quality. Going too small may just wind up in a weird failure. I have not tested this so this is not a recommendation.&nbsp;Lastly, this is not a Hueforge. This model was scanned using a Revopoint Miraco and adjusted in Nomad Sculpt.&nbsp;

Aztec-Mayan Calendar -- The Sun Stone

To Print

Crafty Sven

No supports needed. Make sure that the bed is clean and the first layer adheres properly, glue is recommended.&nbsp;Good luck and happy printing ! ^-^&nbsp;I suggest trying the non AMS version 1st to see if you like the design and size. &nbsp;You can scale this up to 150% !

TPU

Nicole

To Print

Printed