Lode

AU3D

This container is a replica of the original IKEA metal container, designed to mount on either side of any IKEA Skadis board. Measuring approximately 90x80x80mm, it features four sections for easy organization. Additionally, a variant without dividers is included with each print profile on a separate plate. It is compatible to all original boards and DIY boards that follow the same specs. I uploaded a tutorial as PDF file with installation instructions.&nbsp;This model is available for regular mounting <a target="_blank" href="https://makerworld.com/en/models/510561" rel="nofollow noopener">here</a>.<h3>Printing</h3>It is extremely important to use a durable, slightly flexible material with very good layer adhesion as mounting the holder will put some stress on the holder. PETG is the best choice among popular materials but I did all my tests with regular PLA to make sure it will work too. DO NOT USE Silk PLA, matte PLA or any other kind of material that affects layer adhesion negatively. To increase your chances with PLA you can switch the infill type to lightning or add a modifier only covering the mounting bracket and set it to lightning. This will basically remove all infill allowing the walls to bend effortlessly. For most use cases of the holder, this will not affect the overall performance of the holder. From my experience this was not necessary though.<h3>Installation</h3><ol><li>Insert the hooks as far as possible, ensuring that the holder is positioned at an angle.</li><li>Pull the holder towards the outside of the board—in this example, to the left. Simultaneously, push the holder towards the board to keep the hooks inside the holes and guide the holder around the edge of the board.</li><li>The mounting mechanism and hooks may bend slightly during this step, but the material is typically designed to withstand this.</li><li>Ensure the retention lip is completely behind the board, and verify that the hooks remain securely inside the holes.</li><li>Push the holder down firmly, just as you would with any other accessory, to secure it in place.</li></ol>Optional: Use <a target="_blank" href="https://makerworld.com/en/models/92747#profileId-99258" rel="nofollow noopener">this Lock Plug</a> in 10mm to further secure the holder.<h3>Skadis Collection</h3>I am constantly developing more IKEA Skadis attachments. Check out my<ul><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/453266" rel="nofollow noopener">IKEA Skadis Shelves, Trays and Container Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/188108" rel="nofollow noopener">General IKEA Skadis Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/@AU3D/collections/1044616" rel="nofollow noopener">IKEA SKADIS Boards Collection</a></li></ul>

IKEA Skadis Container (Side Mount)

Skadis

WildWolf_3D

Poop Stopper Wall Bambulab A1 and A1 mini-3 color&nbsp;This is my first design for the Bambulab A1, and im very happy with the result :)Easy to print and fits perfectly with the printer.&nbsp;Measures (WxDxH): 14.5x62x18&nbsp;PLA Colors:1.Black2.Grey3.Green&nbsp;Used material: 8.4g&nbsp;Printing time with my settings: 40min&nbsp;Enjoy u prints!

Poop Stopper Wall Bambulab A1 and A1 mini-3 color

A1 Mini

LorenzCR

Does your car have an automatic transmission but you would still like a manual gearbox? Don&#39;t worry, you can use the Gear Shift Simulator!

Gear Shift Simulator

Things

Kit Crafters

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-23_a1fe1017e49a5.png"></figure>Test your skill and launch marbles into a moving basketball hoop under stadium lights!&nbsp;The Mini Motorized Basketball Game is a collaboration project with MakerWorld to showcase the wondeful and infinite possibilities of the new Maker&#39;s Supply kit! This model features a motorized moving basketball hoop, stadium lights, a customizable sign, and an aimable basketball launcher.&nbsp;The motorized moving hoop rotates twice in one direction, before changing directions to rotate twice again. I&#39;m especially proud of this because the motor only turns in one direction, but the output alternates directions automatically using a fairly simple gear system.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-23_37277e02f9ded.webp"></figure>&nbsp;The entire model is assembled using snap connectors, so no glue is needed at all and it will be simple to disassemble if you need to reuse any of the non-printed components.&nbsp;Here are the non-printed components needed (all available in the Maker&#39;s Supply kit):<ul><li>1x 0.5x5x25 mm Helical Spring (BB004)</li><li>1x 2x33 mm Brass Dowel Pin (DA006)</li><li>1x 6003 Plastic Deep Groove Ball Bearings (EA001)</li><li>1x 6204 Plastic Deep Groove Ball Bearings (EA002)</li><li>1x M2.5 Stainless Steel Hex Nut (AB001)</li><li>1x M2.5 Socket Head Cap Machine Screws (SHCS) (AA005)</li><li>1x M2.5 Stainless Steel Flat Washer (AC001)</li><li>14mm Plastic Balls (ZB001)</li><li>1x Power Distribution Board (PDB)</li><li>3x Jumper Cables</li><li>1x On/Off Switch Board</li><li>1x USB Power Cable OR 1x AA Battery Case</li><li>2x LED Board 5v Rectangle (KB001)</li><li>3x Wire 20cm (IC007)</li><li>1x N20 Series Motor with Gearbox 150rpm (LA002)</li></ul>You can see the full list and purchase them from Bambu Lab at the bottom of the page!&nbsp;If you have an AMS, the hoop and the court are multi-colored (with very little wasted filament) to make the project really shine!&nbsp;Everything has been tested on the X1C, A1, and A1 mini! All parts fit on the A1 mini bed.&nbsp;Several pieces in the project use specific settings to ensure the model operates as smoothly as possible:<ul><li>Back Wall - Only part that needs supports, luckily the supports are easy to remove</li><li>Hoop Disk - To counterbalance the weight of the basketball hoop and the ball bearing, the hoop disk has a modifier for 50% infill on half of the model</li><li>Court - This part is printed upside for two reasons, to allow the multicolor to print cleanly and to put the slope on the back of the model to allow the top of the model to be smooth to allow the marbles to roll easily</li><li>Worm Gear - The worm gear is printed with a layer height of 0.12mm (0.4mm nozzle is used) to avoid using supports</li></ul>All of these specific settings are accounted for inside the provided profiles, so no need to do any of these changes yourself if you&#39;re using a Bambu Lab printer.<h2>Build Instructions</h2>Starting with the Court, most of the parts are connected using the printed snap connectors. The snap connectors ‘snap’ into the square/diamond looking holes.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_7228c5c986ef5.png"></figure>Attach the Court Feeders to the Court and insert the small Stabilizer piece into the court before connecting the Launcher Base:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_b7324071e93b.png"></figure>Next, attach the Court Fence and the Side Nets:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_980b0faffb8b1.png"></figure>Next, the Gear System will be put together:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_3e21f4b38ea5c.png"></figure>Slot in the two identical Aux Gears into the center of the Back Wall as well as the Connect Gear:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_8827bc40567eb.png"></figure>Slot in the N20 Series Motor with Gearbox 150rpm (LA002) with the Worm Gear attached. Place the small Output Gear loosely between the two Aux Gears:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_7e7eca2c20c82.png"></figure>Attach the Gear Cover using snap connectors and ensure the small Output Gear from before is in the center of the Gear Cover. Connect the Big Gear to the small Output Gear like so:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_e87d333574008.png"></figure>The Hoop Disk Axle goes into the final hole. Insert the M2.5 x 10 Machine Screw and M2.5 Washer into the Hoop Disk Axle:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_78eb21d3db5df.png"></figure>On the other side of the Back Wall. Attach the Hoop Disk to the Hoop Disk Axle with an M2.5 Nut:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_06e994cfc79f1.png"></figure>Attach the 6204 Plastic Deep Groove Ball Bearings (EA002) into the Hoop Disk:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_82904dda79b4d.png"></figure>The Backboard and the Hoop are friction fit together and attached to the Plastic Ball Bearing:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_eb046add5c036.png"></figure>Attach this finished secdtion to the main model:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_8c7a062fb1336.png"></figure>The Hood and Customizable Sign are then attached on top of the main project like so:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_510f84271e3f2.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_dd6cee89affcc.png"></figure>Next, the Launcher will be put together, starting with the other Plastic Bearing:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_e721e981fcf9.png"></figure>The Launcher to Bearing part and the Bearing Cap snap together through the bearing like so:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_53c726d90ace2.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_5eb952edb124.png"></figure>The Launcher Base is then attached:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_6c0e526c50d2a.png"></figure>The small nub on the Launcher Base and underneath the Launcher Arm allow you to securely attach the 0.5x5x25 mm Helical Spring (BB004):<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_f2dc8416c7e98.png"></figure>The completed Launcher mechanism slots into the main base like so:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_1b94049bd8404.png"></figure>Lastly, the electronic components can be press fit into the following spots on the model:The PDB and the Switch slot into the back of the model:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_927237cfda73e.png"></figure>The LED Boards go under the hood with the wires fed through the holes in the hood:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000420464/design/2024-04-14_b3c0f4da1c499.png"></figure>

Skadis

A1 Mini

Things

Toys