LiosPendragon

Haserti 3D

deckbox with toploaderThis box have capacity for: - 100 Double sleeved cards. - 1 Toploader (3&#34; x 4&#34;) Slot. - 2 Slots for 3 Single sleeved cards for card tokens each side.

Deck Box MTG

MTG Deck Boxes

pops

<h2>[UPDATE] • Triple Containers added due to the requests of some people  • I also added a 4x4 container for large items for heavy duty usage. • Clearances Improved A model to store screws, nuts, nails and other small parts lying around your lab. The parts interlock using the dovetails.</h2><h3> PLEASE PRINT THE TEST FILE FIRST The parts are supposed to have friction, but should slide in easily. If your test parts dont fit you can adjust this using XY compensation in the slicer.</h3>&nbsp;Print settings: Infill: 20% Walls: 2/3 Speed: Slower speed is highly reccomended as the overhangs turn out nicer Layer Height: Any up to .25Support: Not needed

[UPD] SnapStack - A Modular Storage Bin Organizer

Storage Boxes

Fresh3Design

Storage Rack for 5x5 Gridfinity base plates. Can hold 4 plates (100 boxes total).&nbsp;-PETG or stronger recommended.-Print x2 of each braces, lay on side for strength.-Print x1 of each side panels.

5x5 Gridfinity 4 Tray Storage Rack

Gridfinity

PhabulousPhantom

The Grumman F-14D Super Tomcat is the third and final variant of the F-14. The Tomcat is a supersonic, two-seat, Variable-Geometry Wing Fighter jet. Variable-Geometry Wings, more commonly known as swing wings, means the aircrafts wings are not fixed in one position and can change throughout flight. This variant of the F-14 had GE F110-GE-400 engines, upgraded avionics with a glass cockpit, and the AN/APG-71 radar, thus increasing the combat capabilities of the F-14. The Tomcat has had multiple appearances in movies and shows, some of these include The Final Countdown and Top Gun along with its sequel Top Gun Mavrick.&nbsp;I took inspiration from Nakozen's <a href="https://www.printables.com/model/147852-tornado-gr4-kit-card" rel="nofollow">Tornado GR4</a> for the Variable-Geometry Wings. This model was suggested by <a href="https://www.thingiverse.com/Freddy586" rel="nofollow">Freddy586</a> over on Thingiverse.&nbsp;Both Sprue and Sprue-less models included along with models of individual parts. While the fit is relatively snug, glue is recommended.Print at a .2 mm layer height with 100% infill.

F-14D Super Tomcat Kit Card

Cool Kitcards

suaimondi

&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used: PLA+ Esun Black Transmission Distance: 0.6 PLA+ Esun Red Transmission Distance: 6 PLA+ Esun Yellow Transmission Distance: 6 PLA+ Esun Bone White Transmission Distance: 6 Swap Instructions: Start with Black At layer #9 (0.8mm) swap to Red At layer #14 (1.2mm) swap to Yellow At layer #15 (1.28mm) swap to Bone White for the rest.

Red Dragon Girl - Hueforge

Hueforge coolness

Emoticon

The vinyl caps that I have had for different SMA connector radio devices I have were always falling off. I made these with the correct ¼-36 thread so that they stay on and don&#39;t fall off. Print with thin layers for the best detail on the knurling and threads. No supports needed.

MTG Deck Boxes

Storage Boxes

Gridfinity

Cool Kitcards

Hueforge coolness

Radio Stuff

Stuff for Other people

Models to Print