Leo.siwicki

Recursion

Bearing the mantle of the Titan of the Sun, the 'Helios' was designed with a singular vision: to provide a platform for an ultra-lightweight high thrust-to-weight ratio 3.5" DJI O3 FPV build. Harnessing the divine spirit of its namesake, the build is destined to carve paths through the skies, bridging the mortal world and the heavens in its flight.Build/Design/Test Video: <div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=nosRGmP5zSU"><iframe src="https://www.youtube.com/embed/nosRGmP5zSU" frameborder="0" allowfullscreen=""></iframe></div>To get the Carbon Fiber frame cut (and all needed hardware provided if desired): <a href="https://www.cncdrones.com/recursion-helios-35-ultra-light-frame.html" rel="nofollow">https://www.cncdrones.com/recursion-helios-35-ultra-light-frame.html</a>&nbsp;Naked TPU Armored HousingThere are two files available for print. One is “UNCUT”, and the other is cut. This means once you've removed the DJI O3 camera from the stock metal housing, you can put it directly into the housing as is (uncut), or cut away unneeded plastic used for mounting the camera in the metal case to save weight (about 0.2 - 0.3g). This should be printed with the back of the housing facing the build plate. Support should only be needed where the base and the circle housing meets, which is minimal. Be sure to remove any stringing if it occurs inside of the housing to ensure the camera can slide in, as it is designed to be pressure fit inside to secure it. You may add a tiny amount of hot snot (glue) if you want additional security at the edges of the camera at the back of the housing, but this shouldn't be needed.&nbsp;Recommended Build:- Panasonic Low ESR 25VDC 470uf Capacitor - Mfr: EEU-FR1E471Y - Motors: T-Motor F1404 3800Kv (supports any motor with 9mm mounting holes) - Propellers: HQProp T3.5x2.5x3 - Flight Controller: 20x20 or 25.5x25.5 AIO, with a 9.5mm maximum clearance between the center of the 20x20 mount hole and the stand-offs. - Battery: 4s 550mah Tattu or equivalent low internal resistance high quality lipo or greater. A larger battery may be required if you don’t go with the recommended motor/propeller combination. - Video: DJI O3 System, Stock or Naked (Required) - 60mm DJI O3 Camera cable (Stock cable will work) - 10x130mm Battery Strap (For 4s 550mah. Longer for larger) - 2 x 5.8GHz Whip Antennas (only if not using the DJI Remote Controller)&nbsp;SpacersI have also uploaded the m1.6x5mm spacers I used for the Naked O3 airunit. These were made to be as thin and light as possible, so for them to work you'll need to print with the smallest layer height you can get away with with arcane walls. If this doesn't work for your printer, you'll need to make some thicker ones. Reach out if you're stuck. &nbsp;NutsSame commentary as above. These can be used to screw in flight controllers/Naked O3 into the stack. Do not use on the carbon side as metal is important there for increased stability and durability.

Recursion Helios - 3.5" DJI O3 Ultra-Light FPV Drone (Parts)

Drone

Lucas.G

Just reposting this here. All credit go to the original creator <a target="_blank" href="https://www.thingiverse.com/siddv" rel="nofollow noopener">siddv</a> on thingiverse.

Unifi WiFi 6 Long Range (U6-LR) stand

computer 

Canadian Gamer

Detroit Red Wings - NHL Hueforge&nbsp;The rest of my NHL Hueforges can be found in this collection here:<a target="_blank" href="https://makerworld.com/@CanadianGamer/collections/549654" rel="nofollow noopener">https://makerworld.com/@CanadianGamer/collections/549654</a>&nbsp;If you resize the model make sure you do NOT scale the Z axis or the print colours will not be in the same position&nbsp;My Frame is a friction Fit design here for 200x200 Hueforges <a target="_blank" href="https://makerworld.com/en/models/381229#profileId-281475" rel="nofollow noopener">https://makerworld.com/en/models/381229#profileId-281475</a>&nbsp;And if you scale it down, I have frames for 100x100 or 150x150 here:<a target="_blank" href="https://makerworld.com/en/models/173529#profileId-190705" rel="nofollow noopener">https://makerworld.com/en/models/173529#profileId-190705</a>&nbsp;Please post a picture of your printed copy! I&#39;d love to see it!&nbsp;— Printing Instructions--&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used:     PLA Sunlu Black Transmission Distance: 10     PLA Overture Red Transmission Distance: 5     PLA BambuLab Basic Silver Transmission Distance: 0.5     PLA Overture White Transmission Distance: 3Swap Instructions:     Start with Black     At layer #7 (0.64mm) swap to Red     At layer #16 (1.36mm) swap to Silver     At layer #23 (1.92mm) swap to White for the rest.

Detroit Red Wings - NHL Hueforge

Sports

Deurklinkje

Kong Dog Toy Freezer Tray (Extra Large Kong)

Zurlingo-3D

A fun little print in place crossbow - Perfect for annoying work colleagues or classmates! :P&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-03_df05c13d7dc74.gif"></figure>&nbsp;Features:<ul><li>Print in place design</li><li>Fold out trigger mechanism</li><li>Fold out foregrip</li><li>Bolts included</li><li>Very accurate</li><li>Can be extremely powerful</li></ul>&nbsp;<figure class="image image_resized" style="width:48.48%;"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-05_b11734406ec7f.gif"></figure>&nbsp;Post Print:&nbsp;<figure class="image image_resized" style="width:31.3%;"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-03_1338eb107fa83.jpg"></figure>&nbsp;Band Assembly:<figure class="image image_resized" style="width:40.16%;"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-03_245ce4a00326.jpg"></figure>&nbsp;<figure class="image image_resized" style="width:39.75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-03_4ba076cd59b63.jpg"></figure><figure class="image image_resized" style="width:39.38%;"><img src="https://makerworld.bblmw.com/makerworld/draft/405418/2024-01-03_37bb51b6f2f9f.jpg"></figure>&nbsp;Loading:&nbsp;The easiest way to load the crossbow is to:&nbsp;<ul><li>Fold the trigger away as if it was just printed</li><li>Hold in place with one of your index fingers</li><li>With the other hand, pull the rubber band back and hook on the band stop</li><li>Release your finger and gently pull the trigger down</li><li>Pull out the foregrip</li><li>Insert bolt</li><li>Fire!</li></ul>&nbsp;Inserting The Bolts:&nbsp;There is a very small groove in the very centre of the bolt channel and a corresponding male extrusion on the bolt itself.This is there to make the bolt sit short of the trigger mechanism when sliding in to place.This groove is subtle and only there as a guide.&nbsp;Tip: If you want to get some actual power out of the crossbow, then use a length of TPU instead of a rubber band. This will allow the bow to actually flex and at least doubles the power of the bolt. Do this with caution though, as not only does this make the crossbow potentially dangerous (Not suitable for kids) but it can also significantly weaken the bow after several shots. If you get the tension of the TPU right, then you can achieve a happy medium between power and longevity :) Have fun! :P &nbsp;&nbsp;I will be releasing some targets to go with this crossbow very soon.&nbsp;Please follow me for more models and rate and review your printing experience :)

Rubber Band Crossbow - Print In Place - Easy Print

fun things 

bman642

Shower corner shelves. Make singular or as shown with a floating shelf.Optional soap dish, needs to be glued into place. Installation using two screws only.Recommended print setting. Supports - Not needed Layer hight - A 0.6mm nozzle at 0.30mm Layer optimal. Soap dish has been widened compared to as shown in photo &nbsp;&nbsp;

Bathroom Corner Shelf.

Household 

Faran3D

Nuka Cola clock with a realistic bottle cap design.&nbsp;This is designed for AMS printing and prints face-down for a smooth seamless look. The white goes all the way through the face as it&#39;s designed for luminous (glow in the dark) filaments, which are translucent. This should also allow for a nice backlighting effect if you&#39;re wanting to try that out.&nbsp;Two files available with white or black numbers.&nbsp;Please like &amp; share, but don&#39;t steal my design or sell it.&nbsp;If you&#39;d like to buy me a Nuka to support this and future projects <a target="_blank" href="https://www.popsession.co.nz/products/buy-faran3d-a-nuka-cola" rel="nofollow noopener">https://www.popsession.co.nz/products/buy-faran3d-a-nuka-cola</a>

Nuka Cola Bottle Cap Clock

arcade

Behlog

Bear and cub art scene&nbsp;Increase your Z scale for added rigidity!&nbsp;Thanks and Happy Printing!

Bear Wall Decor

artistic 

Bambu Lab

This is an official component set by Bambu Lab for the A1 printer. The AMS lite Top Mount setup is a tested solution for mounting the AMS lite on top of the A1 printer.&nbsp;The component set consists of two main modules:<ol><li>Top Mount Bracket</li><li>Z-Axis Stiffener</li></ol>The Top Mount Bracket is meticulously designed to be tilted to the front for better balance. Additionally, the upper half of the bracket can spin left and right, providing easier access to the back spools.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2023-12-14_ceeb9c0ed0a76.jpeg"></figure>&nbsp;The Z-axis Stiffener is designed to dampen back-and-forth printer movements. Thanks to the special elastic damper design at the bottom, there is minimum wobble even when printing in ludicrous speed with AMS lite fully loaded.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2024-04-23_cafcdb16e7224.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000092486/design/2024-04-23_4980ec2ffcf67.jpg"></figure>&nbsp;AssemblyHere is a tutorial video for the installation:<figure class="media"><div data-oembed-url="https://youtu.be/RmZOgrcDiRQ"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/RmZOgrcDiRQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;You can also buy the required hardware as a kit from here:<a target="_blank" href="http://store.bambulab.com/products/ams-lite-top-mount-screws-kit" rel="nofollow noopener">http://store.bambulab.com/products/ams-lite-top-mount-screws-kit</a>&nbsp;&nbsp;&nbsp;&nbsp;

AMS lite Top Mount for A1

printer accessories 

Cjwelcome

This mechanical Pill organizer box can help store even some of your larger pills for a convenient and labeled AM-PM cycle. This design uses absolutely no supports whatsoever in order to provide you the most user friendly experience in printing with ease. Simply print the components and throw them together for a super cool lever action dispenser with a satisfying click to its internal ratcheting mechanism! No need to remove components or disassemble this box for refills, simply open the lid and replenish your next weeks dosages. Stands upright for easy storage in your cupboard or bathroom medicine cabinet. Continue reading below for any updates and Enjoy!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-05_32261aba83369.gif"></figure>EDIT 1: Added a pill fit tester so you can see if your amount of pills fit in the very quick spiral vase print then that is how much volume each section has available. Many people cant quite guage how much room each section has so this seems like it will help everyone out if they arent sure and dont want to waste time printing the whole thing. Happy Printing!&nbsp;EDIT 2:•Added V2 box which fixes empty spaces inside the box which could potentially jam smaller pills inside when using.•Added multiple language labeled drums! English, Spanish, Polish, German, French  and now Romanian! If there&#39;s a language you&#39;d love to see included then drop me a DM!&nbsp;EDIT 3:•Some people seem to have some fitment issues with the inner rotating drum. For this I&#39;m sorry and looking at my model that specific part has ~0.15mm Radial tolerance (Tol.= 114.3mm - 114mm / 2 = 0.15mm Radial Tol.) which for some printers can become too tight. For this I recommend printing everything else the same but for the center drum, print it at 99.5% scale should put the drum around 113.5mm, adding another 0.25mm radial tolerance if your printer seems to print too tight which should solve that issue of fitment.•Second is more of a simple sizing request for some. For everyone who loves the design but thinks its a little on the small side for the amount or size of pills they need to take, I have found a solution in the very easy form of scaling the model! For every component except the center drum, you will want to scale up from 100% to 120%. The main case will need to be rotated 45° then upscaled and all others small components can just be upscaled to 120% as they currently sit. The center drum in order to keep it from being too tight, scale it up only to 119.75%. That should be able to then hold up to six (27mm L x 10mmØ pills) in every section and still be under 6&#34; tall. If you upscale it to 120% and the mechanism doesnt seem to be clicking the drum into place that is because the tolerance of the ratchet wheel under the drum will now have a little slack in it. To solve this, place a small piece of electrical tape or scotch tape on one or two faces of the sqaure peg on the base until the ratchet sprocket has no wiggle room shown below.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-07_e78b9474b42e.jpg">&nbsp;EDIT 4: Some people gave feedback that their prints were too tight of tolerance and the center drum would not be able to spin or the main hinge was binded and would snap at the base when trying to break it free. Another issue of individuals that need to take smaller pills or chalk like pills would have them break and or become caught in the lever arm above the opening section. To solve these issues I have opened up the tolerance for both the drum section and beefed up the hinge of the main box as well as added a fin section that covers the lever arm allowing the pill section to be fully covered allowing no space for pills to get caught between. The only difference is with the assembly which will require a small drop of superglue at the three pin locations for the two alignment slots and the central lever pin cavities. Because few of these instances have occured, the V2 will remain available for people to download and print but if you are interested in a bulkier hinge, looser toleranced and no risk at all of pills getting caught at the open ended section then V3 is for you. Im always open to feedback and Italian labeled drum is soon to come for this edit #4!&nbsp;&nbsp;ASSEMBLY INSTRUCTIONS: Be sure your parts are free and clear of wispy strings and your machine/filament is properly calibrated for accurate printing. These models are meant to assembly together with relative ease and tolerances but improper printing/old filament can cause tolerances to seem tight. Make sure the notch mark on the Drum-Lock ring is facing the front pill opening of the box or else the ratcheting mechanism will not line up properly.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-05_43efbd423805d.gif"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-05_9a1e8430cd059.jpg">(V2 Assembly):May or may not have some tight fit issues on case by case basis and potential for pill to get grabbed by the lever arm.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-05_63d37f8c0c547.gif">(V3 Assembly)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-11_042dd9cb10122.gif"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000172691/design/2024-02-11_91df90be1061.png">&nbsp;!CAUTION!…Be sure to keep away from children as we all must remember that these are still for pill/medication storage and must be treated as such regardless of how cool 3D printing their storage is. Be safe and happy printing!&nbsp;