LYC.FYI

CPDesign

I designed this organiser for my girlfriend&#39;s Skadis board for pencils, brushes, scissors, etc. It has two “pockets” with dividers.&nbsp;printing preferences on BBL P1P:<ul><li>printed in Redline PLA</li><li>0,2 mm standard quality</li><li>20% infill</li><li>brim auto</li><li>tree support </li></ul>printing time was ca. 4 hours.

Organiser for Ikea Skadis

Organizer

PrintThatBoii

This is a scalable Christmas tree with shoes because everything is better with some shoes and a face XD. The first tree is at scale 75% the middle is at 100% and the right one is at 50%. You can go bigger if you want. note that the smaller you go the harder it is to get the shoes in. At the scale of 50% you have to push a bit harder than the one on 100%. 3D PRINTING:You can print this with a layer height of 0.2 (for the 50% tree and the shoes) or 0.3mm. You don’t need supports. I would recommend dropping the shoes 1mm lower in the slicer as the shoes are a bit too round in the front. I printed them with 15-20% infill (trees and shoes). If you read this in December, Happy Christmas! &nbsp;I borrowed the shoes from @FatherLicorice and his cute little ghosts. &nbsp;

Cute Christmas tree with shoes

Nicole

Black Jack

A snowcat/snow groomer is a large vehicle mainly used to pack snow and improve conditions for skiing, snowboarding, and snowmobile trails. Apart from these functions, it can also be modified to fit exploration and other niches&nbsp;I am very thankful to <a target="_blank" href="https://www.printables.com/@BenoitLussier" rel="nofollow noopener">Mr Benoît Lussier</a> for his feedbacks which has helped me refine the model further. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2024-02-05_5719c6a5bba03.gif"></figure><h3>There are three ways to print this.</h3><ol><li>As single piece:- Please download STL file but there wont be any movements.</li><li>Multiple Pieces :- Download 3mf file with Full_dismantled.3mf.BEST QUALITY OUTPUT. Please use the 3mf file for assembly also.</li><li>Combined:- You may use any 3D viewer software like 3D builder in windows to merge components according to your printer and filaments. The sky is the limit for this. You may find a sample file ending with combined.3mf.</li></ol><blockquote>If you want to try TPU for tracks, you can download the "Snowcat_TPU_track.3mf" which has the tracks and gears. You will need to replace all the 12 gears in PLA version with the provided gear for TPU track working. but please note that I haven't tested them.</blockquote><h3>ASSEMBLY OF MAIN CAB</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_sf2j5kerx47h.gif"></figure><h3>ASSEMBLY OF UNDERCARRIAGE</h3><figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_uj7umkj0hbek.gif"></figure><h3>ASSEMBLY OF FRONT BUCKET</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_ie6333ytqrdh.gif"></figure><h3>ASSEMBLY OF REAR GROOMER</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_sgq5nfo1l1g4.gif"></figure><h3>ASSEMBLY OF WINCH</h3>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_y8q9l3zlq488.gif"></figure>The beam of the winch has a 2.25mm diameter path cut through it to route the rope to operate the winge. Here you have two options. either use a rope with max diameter of 2mm or a 1.75mm 3D printing filament. If you choose the first case you can tie the rope to the hook and route the rope through the beam and then through the rotating platform can reach the winding drum. In this case you can skip the winding spool design over the drum and use the hole on the drum to tie the rope and wind. If you choose to use a filament, it would be a make belief thing and thus no need to route it past the rotating plate. See the image for reference. The yellow part is the rope/filament.<figure class="image image_resized" style="width:66.85%;"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_3a6bbf5ed9f9.png"></figure><h3>MATING OF ALL PARTS</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2023-11-16_tf2i9qd52uec.gif"></figure><h3>Movements Included</h3><ol><li>Front Bucket Movments</li><li>Rear Groomer swing and lift</li><li>Crane Operations</li><li>Track movement (only with TPU - Untested)</li></ol>NOTE The tolerances to some elements are zero which has been intentionally provided to friction lock the elements while not in movements. You may have to fine tune the tolerance from your end using scaling function in slicer to ensure good fit without compromising movements. This also applies for the pins that make rotation possible between elements. Please proceed with printing all the pins after testing printing a pin and testing the fit of a joint. You should be able to find the adequate scaling factor with this.Supports should be provided as required.Appreciate the makes uploads. Open for suggestions.<a target="_blank" href="https://www.buymeacoffee.com/blackjack123" rel="nofollow noopener"><img src="https://media.printables.com/media/prints/649176/rich_content/03fc3dbc-cf8a-4340-a13c-57fc7f28cbc3/download-assets-sm-1.png#%7B%22uuid%22%3A%22f855135a-522c-4f22-9e87-de6df7452f1b%22%2C%22w%22%3A260%2C%22h%22%3A73%7D"></a> <a target="_blank" href="https://www.patreon.com/BlackJack123" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/768364/2024-02-10_833e9bfdbf3.png"></a>

Yellow Modern Snowcat / Snow Groomer

玩具

CATIAV5FTW

1/2/2024 UPDATE: I have incorporated several minor design improvements to the parts to improve clearances, ease of printing, and ease of assembly. Parts require fewer supports as well. These updates are included in the Jet Engine Model for Kit-006 print profile. This is the latest and greatest profile, so I highly recommend using this from now on. The parts from the previous release, now renamed (OLD) Jet Engine Model for Kit-006, are still compatible with these new parts, however, so you don’t have to reprint the whole thing if you don’t want to.&nbsp;Overview:A cutaway model of a 2-spool high bypass turbofan. I designed the whole engine from scratch with cues to certain existing engines. For example, I think Rolls-Royce makes the best-looking fans, so there&#39;s some resemblance there... Since originally uploading to Thingiverse in 2016, the popularity of this model has grown far beyond expectations. The model has appeared in numerous publications, additive manufacturing expos/conferences, and is (for better or worse) being made and sold by a number of 3rd parties. However, rest assured that this is one of the official sources for this model. A bunch of remixes of this engine are out there, mostly in Thingiverse at the moment, if you are so inclined. I&#39;ve also designed an <a target="_blank" href="https://makerworld.com/models/158422" rel="nofollow noopener">alternate fan for this engine</a> that more closely resembles GE and P&amp;W engines. Check it out!&nbsp;I uploaded a diagram with labels to all parts for reference. For more detailed instructions, the YouTube assembly guide at the bottom of this description walks you through the process.&nbsp;Please refer to the BOM (Bill of Materials, aka Parts List) below for keeping track of what parts to print.&nbsp;===The required fasteners (screws, washers, and nuts) and ball bearings are listed below. However, to make your life easier, there is an official hardware kit that includes these components: <a target="_blank" href="http://shrsl.com/4cfq0" rel="nofollow noopener">Jet Engine Model Components Kit - 006</a>. <ul><li>Metric machine screw, allen socket cap, 2.5mm x 0.45mm x 10mm (QTY 100)</li><li>Metric flat washer, 2.5mm (QTY 200)</li><li>Metric hex nut, 2.5mm x 0.45mm (QTY 100)</li><li>6204 open ball bearing 20x47x14 (QTY 2)</li><li>6003 open ball bearing 17x35x10 (QTY 2)</li></ul>The jet engine will look great in any filament, but what I recommended (and what is pictured) are the following:<ul><li><a target="_blank" href="http://shrsl.com/4cfqh" rel="nofollow noopener">PLA Basic Jade White</a></li><li><a target="_blank" href="http://shrsl.com/4cfqm" rel="nofollow noopener">PLA Basic Blue-Gray</a></li><li><a target="_blank" href="http://shrsl.com/4cfqs" rel="nofollow noopener">PLA Basic Black</a></li><li><a target="_blank" href="http://shrsl.com/4cfr0" rel="nofollow noopener">PLA Metal Cobalt Blue Metallic</a> --OR-- <a target="_blank" href="http://shrsl.com/4cfrd" rel="nofollow noopener">PLA Metal Iron Gray Metallic</a></li></ul><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=dNsBbN54J-I"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/dNsBbN54J-I" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Jet Engine Model Components Kit - 006 and filament through the links above, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to the public.) ===&nbsp;Good luck and happy printing! Message me with any questions!

3D Printable Jet Engine

摆件

3DMN

If you appreciate my work, give it a like, and if you love it, consider buying me a coffee to show your support! <a target="_blank" href="https://www.paypal.com/donate?hosted_button_id=BC7SWTMZG92TG" rel="nofollow noopener">https://www.paypal.com/donate?hosted_button_id=BC7SWTMZG92TG</a>&nbsp;&nbsp;Check out my other Hogwarts model: <a target="_blank" href="https://makerworld.com/en/models/134009#profileId-145435" rel="nofollow noopener">https://makerworld.com/en/models/134009#profileId-145435</a> &nbsp;&nbsp;Step into the enchanting world of Harry Potter with our meticulously crafted Hogwarts Castle model! This exquisite replica captures the magic of J.K. Rowling&#39;s wizarding world with precision and attention to detail, making it a must-have for every Potterhead.&nbsp;Standing at an impressive x200 y185 z104, this Hogwarts model is a true testament to the grandeur of the iconic wizarding school. Every turret, tower, and spire has been faithfully recreated, allowing you to bring the mystical charm of the castle into your own space.&nbsp;Whether you&#39;re a collector seeking the centerpiece of your Harry Potter memorabilia or a fan looking to add a touch of magic to your home, Immerse yourself in the wizarding realm and marvel at the intricacies of the magical world with this stunning representation.&nbsp;&nbsp;

Harry Potter Hogwarts

Harry Potter

OlleMark

Updates:2023-10-27 - Redesigned the nozzle cleaner slots so you can flip the box without them jumping around.&nbsp;A smaller sized accessory box aimed to fit most of the accessories that the bambu printers are shipped with.&nbsp;Larger version here: <a target="_blank" href="https://makerworld.com/en/models/52449#profileId-54209" rel="nofollow noopener">https://makerworld.com/en/models/52449#profileId-54209</a>&nbsp;The lid is a slide on design because i wanted something that can stand open without taking up too much space but still be able to close and be put away. The lid can slide on the underside of the box to get it out of the way fully which makes the box take up way less space compared to a normal box.&nbsp;The lid has the bambu logo engraved for painting, it is invisible until you start painting. A untested painted version will be available to print for the ams users.&nbsp;I printed mine with white clas ohlson pla.&nbsp;It fits:2 hotendsbambu printing adhesive 4 nozzle wipersboth allen keysmost of the miscellaneous bags of screws and lube

Compact Accessory Box for P1 and X1 Series

打印机周边

ME STUDIO

<h4>[FREE 1 DESIGN] Pokemon Ball Coaster</h4>Please share with me your printing image. By doing so, you will have the opportunity to receive special printing files such as Pokemon character coasters, keychains, and more.Thank you!&nbsp;If you love my works, please come to download a set of 6 coaster, check out my 3D models library.Dimensions: 100 mm diameter 4 mm heightThis model is for private use only! Welcome to join my Patreon, you can get monthly models and a welcome package.<a target="_blank" href="http://patreon.com/MESTUDIO" rel="nofollow noopener">http://patreon.com/MESTUDIO</a>

[FREE 1 DESIGN] Pokemon Ball Coaster

周边

Tactical Kaoz

🎄 Unveil the magic of the holiday season with our exclusive 3D-printable ornament-container! 💜 Perfect for your family, this unique, ornament 🟣 ingeniously opens up to hide your festive treats or precious gifts 🎁. Crafted with love and a touch of holiday cheer🤗 Get yours and add a personal twist to your tree 🎅Become a member for access to all of my designs 😁 Continue enjoying this perk for as long as you are subscribed, plus the commercial rights to start selling your creations of my designs immediately: <a target="_blank" href="https://linktr.ee/tacticalkaoz" rel="nofollow noopener">https://linktr.ee/tacticalkaoz</a>&nbsp;<ul><li>The Gold Crown needs to be glued to the top part of the Ornament.</li></ul>&nbsp;<ul><li>If you want a Fuzzy Ornament you will need to print out the Fuzzy Ornament Print Profile.</li></ul>

CHRISTMAS SECRET ORNAMENT CONTAINER

节日装饰

Bambu Lab

The 3D model consists of two circular badges, one featuring the Bambu Lab logo and the other displaying the "Bambu Lab" text. Both badges are painted with a combination of white and green colors, giving them a clean and contemporary look. The badges are designed with precision to create a sense of depth and texture, adding to the overall visual appeal of the model. This 3D representation effectively showcases the Bambu Lab brand with its minimalistic yet striking design.

Organizer

Nicole

玩具

摆件

Harry Potter

打印机周边

周边

节日装饰

Badge