LOVELYBORI

Williams Industries

Here is an update to the great MF DOOM mask. Added a larger gem and cut the file so it is flush so you can have a better finish on the top part. This looks stunning with silk filament. When using silk filament, be cautious of temps (including gusts of wind from opening and closing printer door and the like) as it may cause issues with the finish. The profiles added have minimal and easy to remove supports. Below I have also added what I use to make the mask wearable.&nbsp;Remember kids, ALL CAPS when you spell the man&#39;s name.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000466290/design/2024-05-16_d906e099292b38.gif"> Profiles available: 1. Color Gem- Gem is colored, this does add a lot of extra time, but looks cool2. Single color- Gem will be the same color as the mask. Easy to paint, but also looks cool as is&nbsp;Supplies to make it wearable (affiliate links) :<ol><li>Strap- <a target="_blank" href="https://amzn.to/3UENes6" rel="nofollow noopener">https://amzn.to/3UENes6</a></li><li>Slider- <a target="_blank" href="https://amzn.to/3K53ldB" rel="nofollow noopener">https://amzn.to/3K53ldB</a></li><li>Glue- <a target="_blank" href="https://amzn.to/3V18slq" rel="nofollow noopener">https://amzn.to/3V18slq</a></li></ol>&nbsp;We have a lot of great stuff over at the Patreon: <a target="_blank" href="https://www.patreon.com/WilliamsIndustries" rel="nofollow noopener">https://www.patreon.com/WilliamsIndustries</a>&nbsp;We release about 30 files a month. Patreon membership includes commercial use on all prints.<figure class="image"><a href="https://patreon.com/WilliamsIndustries?utm_medium=unknown&amp;utm_source=join_link&amp;utm_campaign=creatorshare_creator&amp;utm_content=copyLink" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000466290/design/2024-03-13_967b85ee2294b8.png"></a></figure>&nbsp;

MF DOOM MASK

MASKS

Stigern

Simple figurine of a sitting frog.&nbsp;Adding two profiles, one with adaptive layers and one without.There are a few supports, but not much and they are easy to remove.&nbsp;&nbsp;&nbsp;Hope you like it.

Cute Sitting Frog Figurine

DECOR

mocodroid

Nutcracker over 24 inches tall.Printed with PLA at .2 mm layer height 15% infill (I like gyroid), 2 perimeters and .4 nozzle size. No supports required (the head printed fine upside down without supports). Parts are marked for the respective places on the model. The only parts that you need 2 of are the hand, arm, leg and boot. Head and hat are hollow. I used contact cement to glue everything together. Eyes are a 3 parts object ( eye, Iris and pupil ) and the mouth 2 parts ( teeth and lips ). There is a Left eye and a Right eye parts, top mouth, top teeth and lower mouth and lower teeth. All the parts are printed with the flat side facing the printing bed. Head, hat, arm and hand are printed upside down. You can do layer color change to print some of the pieces in two colors. You might need to sand a bit the hole for the Jaw pin. If you have any questions regarding the model send me a message. I don't now if the tolerances will work if you scale the model up or down, if they do please let me know in the comments section.Happy Holidays!!!

MASKS

DECOR

HOLIDAY