LL-Project

KobaRiley

<h2>Cable Tidy for Bambu X & P Series</h2>Got a bit tired of the messy setup on the back of the printer, and designed some cable supports that don't need screws or magnets.Also got a bit carried away and designed a few different versions.&nbsp;The PTFE tube on the right side, that goes to the printer, is free to move back and forth, but stays in the channel.The cables and tubes keep everything in place, but I've added some double sided tape on mine to keep it a bit tidier.<h3>Install</h3>To install the plate, you need to remove the two cables, and the left hand side PTFE tube. Then, remove the PTFE tube at the connector closest to the printer… feed that tube through the hole in the cable tidy plate, and then just reconnect everything.&nbsp;I've had this running on two printers for about 20 prints each, and have had no issues.&nbsp;There are different designs available, from 4, 3, 2 and 1 colour. The 1 colour basic version is by far the fastest to print… The Texas version is my favourite, and looks much better in reality than my awful photos….&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_432ca9585a8cb.jpg">&nbsp;&nbsp;The cables and tubes can still be removed with the standard little tools that are everywhere on Makerworld, but I've included a couple that fit slightly better with with this plate.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_6a6ab2a212209.png"></figure>&nbsp;This project took several days, and many many test prints. If you like the model, and feel like buying me a coffee, it would be greatly appreciated. <a target="_blank" href="https://ko-fi.com/kobariley" rel="nofollow noopener">https://ko-fi.com/kobariley</a>&nbsp;

Cable Tidy - X1- P1S - P1P

Bambulab

JamesThePrinter

A selection of Halloween ghosts that use LED tea lights to glow.Short Models (100mm Tall)<ul><li>Scary Ghost</li><li>Spooky Ghost</li><li>Happy Ghost</li><li>Blank Ghost - Design your own face! (.f3d and .stl included)</li></ul>Large Models (150mm Tall)<ul><li>Scary Ghost</li><li>Spooky Ghost</li><li>Blank Ghost - Design your own face! (.f3d and .stl included)</li></ul><figure class="image image_resized image-style-align-center" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/70395/2023-09-12_nh65u2uq6cpe.gif"></figure>Most tea lights have a 38mm (1.5in) diameter. The openings in these models are slightly oversized, so most (if not all) tea lights will fit. Just turn on the LED and set your ghost on top. If you are worried about getting lights that fit, <a target="_blank" href="https://amzn.to/3YQGEA9" rel="nofollow noopener">these</a> are the tea lights that I used.&nbsp;Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.&nbsp;Print SettingsThese have all been designed to print with 2 perimeters and require no infill. Some overhangs in the mouth and eyes require good cooling.&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Sunlu PLA White</li></ul>

Glowing Ghosts!

Altro

kjbturok

Cable box holder 160x62mm for Ikea skadis or similar.If you need it in a different size you can always try to scale the model without hooks and add the hooks later.The brand of cables I use:https://www.amazon.es/gp/product/B07TT68455/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1&nbsp; ESPAÑOL Soporte para caja de cables de 160x62mm para Ikea skadis o similar.Si la necesita de un tamaño distinto siempre puede tratar de escalar el modelo sin ganchos y agregar los ganchos posteriormente.La marca de cables que uso:https://www.amazon.es/gp/product/B07TT68455/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1

Bambulab

Altro

Accessori