KongHei

Tassesin

Thanks to all who liked and supported my <a target="_blank" href="https://makerworld.com/en/models/407405" rel="nofollow noopener">first version of 608 Roller Bearing</a>, I was inspired to design new and better 3D printed 608 roller bearing! Unlike my first version which relies on low friction, I wanted to design a rolling 608 bearing with a real mechanical bearing principle. So after hours in front of the CAD, printing, testing, and all over again here it is. As my previous model, this one follows the same O.L.S. Design - Optimal tolerances for Low friction and Stability.&nbsp;Printing tips:It is important to use the provided print profile. It was carefully tailored together with the model to challenge the low tolerances.&nbsp;Post-processing:To break up the bearing and any micro adhesions push the cage and the rollers a couple of times alongside the bearing axis, then roll the outer ring for a minute.&nbsp;Let the rolling begin!&nbsp;If you need a spool roller, you can check the <a target="_blank" href="https://makerworld.com/en/models/488060" rel="nofollow noopener">Ultimate Spool Roller for 608 bearings</a>. <a target="_blank" href="https://makerworld.com/en/@jedipiehut" rel="nofollow noopener">JediPieHut&#39;s</a> simple and sleek design is specially designed for these bearings, for which I thank him!&nbsp;P.S. If you like my work please boost, like, rate or comment. This will help me to continue materializing my ideas in this new world for me. Happy printing! You can check my other models <a target="_blank" href="https://makerworld.com/en/@Tassesin" rel="nofollow noopener">HERE</a>.

608 Roller Bearing V2

其他

mlodybuk

(A1 VERSION IN MY OTHER MODELS)During this upgrade, some parts of your printer may be damaged, I am not responsible for any damage caused by incorrect installation or other damage. If your cables appears too short for this mod you should not install it.This model allows A1 MINI users to adjust camera angle! I remixed well prepared @henlor A1 Mini faceplate model (by adding a mounting hole) with my A1 camera holder&nbsp;INSTRUCTION (It&#39;s prepared for A1 version but will work the same with Mini version): Print all 3 models as they are in print profile, camera holder should be printed with supports DURING NEXT OPERATIONS THE PRINTER SHOULD BE TURNED OFF! <a target="_blank" href="https://wiki.bambulab.com/en/a1-mini/camera-replacement-guide" rel="nofollow noopener">Remove original faceplace and camera according to BambuLab instruction</a> Push camera into it&#39;s new holder, it&#39;s supposed to be pretty tight so vibrations won&#39;t make any noise<img class="image_resized" style="width: 284.109px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_a421953c70d76.png"> Put new faceplate on the X-axis with the cable going through a hole and carefully bend the connector 90 degrees, it&#39;ll be easier to connect it.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_5b47781f95f6e.png"></figure>Push the cable through camera holder hole and connect it.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_6ca89baf6ea96.png"></figure>Push in the camera facing down and rotate it so it locks<figure class="image image_resized" style="width: 221.188px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_0b6d72aa1e2e6.png"></figure><figure class="image image_resized" style="width: 215.5px"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_4d5b7eaf58244.png"></figure>Put the back cover and adjust the angle<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_caaebee990e58.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000476062/design/2024-05-26_e28e8825bf046.gif"></figure>

Bambu A1 MINI Adjustable Camera Holder

A1 mini 配件

SugarPaws3D

Introducing the Flexi Alligator, also known as the &#34;Swamp Puppy&#34;!&nbsp;This adorable and fun design features fully articulated joints in the head, body, arms, legs, and tail, allowing fun fidgety movement!&nbsp;This easy-to-print model requires no supports, ensuring a smooth and hassle-free printing experience.&nbsp;Filaments Used:BambuLabs - Matte Dark GreenBambuLabs - Matte Ivory WhiteBambuLabs - Matte Charcoal&nbsp;Curious about the creation process?<a href="UCid7C5baH0w29BVXxRAOI2A" rel="nofollow"> </a><a target="_blank" href="https://www.youtube.com/watch?v=yhVrdXl4dRA" rel="nofollow noopener">Check out my Youtube link</a> to see how this adorable model came to life! I included the full modeling, slicing, and printing process ( : <a target="_blank" href="https://www.youtube.com/watch?v=yhVrdXl4dRA" rel="nofollow noopener">https://www.youtube.com/watch?v=yhVrdXl4dRA</a>&nbsp;<a target="_blank" href="https://patreon.com/SugarPaws3D?utm_medium=unknown&amp;utm_source=join_link&amp;utm_campaign=creatorshare_creator&amp;utm_content=copyLink" rel="nofollow noopener">Commercial License + exclusives + early access available on Patreon: SugarPaws3D</a>

其他

A1 mini 配件

玩具

干燥箱