Kamil drukuje

Once in a Six Side

Here&#39;s the source coupling modified to be a perfect fit with any Elegoo Saturn printer that has the built in fume extraction port. This part is to be used with V3 of the Fume Extraction system. v3 Fume Extraction System: <a target="_blank" href="https://makerworld.com/en/models/487870" rel="nofollow noopener">https://makerworld.com/en/models/487870</a> Note: This STL file has a 0.2mm tolerance built in. If you need to adjust the tolerance then you must download the F3D file and update the tolerance parameter. Instructions on how to do this can be found <a target="_blank" href="https://youtu.be/loN8yAy-9dc?si=Gg-x_6FALOVug-I0" rel="nofollow noopener">HERE</a>.

Fume Extraction OIASS V3 For Elegoo Saturn

saturn 4

ALERT!! There&#39;s an even BETTER version of this available now: <a target="_blank" href="https://makerworld.com/en/models/487870" rel="nofollow noopener">https://makerworld.com/en/models/487870</a> Hey folks,&nbsp;I wanted to design a fume extraction ventilation system for 3D printers that could take advantage of some affordable and widely available components, be extremely flexible and work for whatever your printing setup looks like, and help keep those nasty resin fumes outside. The fittings have a quick disconnect feature that uses 10x2mm neodymium magnets, and couples the hose firmly into position at any point you want to extract fumes from. Just install an outlet fitting anywhere you want to vent; directly on your printers enclosure, above your workspace in a flow hood, a cabinet or large enclosure you keep all your printers in etc. This lets you quickly move the fume extractor to wherever you need it, and there&#39;s an included outlet cover with a handle that you can use to block off the outlets when the hose isn&#39;t connected.&nbsp;You can print the entire thing without supports! I used Esun PLA+ and a 0.3mm layer height&nbsp;Here&#39;s a video on the system&nbsp;&nbsp;What you&#39;ll need | Affiliate Links &lt;3 4&#34; Inline Fan - <a target="_blank" href="https://geni.us/E31MO" rel="nofollow noopener">https://geni.us/E31MO</a> 4&#34; Vent Hose - <a target="_blank" href="https://geni.us/DSqwco" rel="nofollow noopener">https://geni.us/DSqwco</a> Plank of wood that fits your window or an AC Window Kit <a target="_blank" href="https://geni.us/AEv78e" rel="nofollow noopener">https://geni.us/AEv78e</a> 10x2mm Neodymium Magnets - <a target="_blank" href="https://geni.us/i8uAI69" rel="nofollow noopener">https://geni.us/i8uAI69</a> M3 Bolts (I used a mix of M3x8 and M3x12) - <a target="_blank" href="https://geni.us/TVsnB" rel="nofollow noopener">https://geni.us/TVsnB</a> 80mm Hole Saw (with teeth, not the diamond type) - <a target="_blank" href="https://geni.us/xPTj" rel="nofollow noopener">https://geni.us/xPTj</a> Insect screen mesh - <a target="_blank" href="https://geni.us/17df2" rel="nofollow noopener">https://geni.us/17df2</a> Hose clamps - <a target="_blank" href="https://geni.us/hRDvaG" rel="nofollow noopener">https://geni.us/hRDvaG</a>Tip: Depending where you are it may be significantly cheaper to source the insect screen mesh and hose clamps locally. For most of the other parts I found better deals on ebay so check there as well, but thank you for using my affiliate links. Recommended tools Power Drill Staple Gun Hand saw&nbsp;I recommend using super glue for the magnets. That&#39;s what I did and so far they&#39;re still going strong, and none have popped out.&nbsp;Update 05/03/2024 WE&#39;VE GONE PARAMETRIC BABY!! That&#39;s right, you can now download these files in glorious F3D format. I&#39;ve remodeled them from scratch using the parametric tools in Fusion 360, and now you can modify til your hearts content and customize these models to your EXACTING DEMANDS. Notable highlights of the update include:<ul><li>Easily configure the models for embedded magnets that fit your print settings and preferences perfectly</li><li>Quickly adjust the tolerances to suit your printer and magnets</li><li>There&#39;s now a fast tolerance test print to dial in your tolerances</li></ul>All the parameters are commented, and there&#39;s a video that shows off everything that&#39;s been changed and what you can do now with the power of the parameters - so go watch that right now right here. The included STLs here come with a 0.3mm tolerance built in for the magnets, so I would recommend printing the tolerance test part first and checking the fit with your 10x2mm magnets, and then adjust the tolerance parameters accordingly.  &nbsp;If these files have helped improve your 3D printing experience, please consider a small donation or becoming a member on BuymeaCoffee or Patreon. Every bit helps! Members enjoy a bunch of awesome extra STLs too <a target="_blank" href="https://www.buymeacoffee.com/onceinasixside" rel="nofollow noopener">https://www.buymeacoffee.com/onceinasixside</a> <a target="_blank" href="https://www.patreon.com/onceinasixside" rel="nofollow noopener">https://www.patreon.com/onceinasixside</a>&nbsp;

Magnetic Quick-Disconnect Ventilation system - V2

resin

chiz_m

<h3>RELEASE HISTORY</h3>2023-12-17: Thinner version print profile added that may work better for others with printers that don&#39;t have the frames completely flushed. See Tips for Success section below for more details.2023-11-17: Version 2 - now covers the entire length of the lead screw and more rigid. Additionally, magnets can now be added.2023-11-12: Initial Release________________________<h3>If you find that this shield works great for you, pls hit that BOOST button!</h3><h3>PROBLEM</h3>Grease from the z-axis lead screw would often get into hands/arms when getting finished prints from the printer.<h3>SOLUTION</h3>Design a shield that would cover the lead screws but not affect the printer functionality.<h3>IMPORTANT NOTE (Please read first!)</h3>As the tolerances in the assembled unit varies, this lead screw cover might not work on your printer. See item #1 below in the Tips for Success section. The left side of the printer has very little room to fit the shield and if you have a really skewed printer frame, the shield could rub against the print bed assembly. I noticed this difference between the two (2) X1C&#39;s that I have. You can try the thinner version as it might fit better to your unit over the regular version. Lastly, this requires a really calibrated filament for the part to fit. Over extruded filament will cause the part to be thicker and very tight while under extrusion would make the part thin and loose. Please do NOT rate the model low because it didn&#39;t fit well to your unit, which may have really skewed frame or your filament isn&#39;t calibrated correctly. A lot of people have successfully installed this shield and continue to use it today without issues.<h3>PRINTING DIRECTIONS</h3><ol><li>Print as oriented.</li><li>Model has built-in support. Remove supports after printing.</li><li>Part clips to the z-axis lead screw bearing mount. Optional: Add 8x3mm magnets.</li><li>Left and right shield are mirror of each other. Flip in the x-axis in the slicer to print the other. Alternatively, print using the provided left and right profiles.</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000062988/design/2023-11-17_e498439f53add.png"></figure><h4>TIPS FOR SUCCESS</h4><ol><li>Variances in the unit assembly. I found it myself that there are variances in the assembly of the units that may affect the fit of the shield esp. on the left side. See picture below. You can see on the left (blue) that the lead screw mount is flushed to the vertical post of the frame compared to the one on the right (light brown). This makes the shield pushed against the print bed support and might not fit well. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000062988/design/c3bcc624-ac61-4c7f-be2c-e34a4ee3bf82.webp">  </li><li>Curved edge. If you happen to get the printed part from the print bed when it&#39;s not fully cooled down yet, you might have a curved edge. This will cause the print bed support to rub against the curved edge of the shield.  <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000062988/design/bdaca8b8-c292-4044-8224-715515a9ba55.png"></li></ol><h3>MATERIAL RECOMMENDATIONS</h3><ul><li>Use high temperature resistant material like PETG, ASA or ABS as PLA might warp overtime.</li></ul>

X1/X1C Lead Screw Shield

ZEE SOLO

A filament swatch holder for Skadis boards. It can house 29 swatches (for this <a target="_blank" href="https://www.printables.com/model/147518" rel="nofollow noopener">model</a>).Mounted using the <a target="_blank" href="https://www.printables.com/model/256896-skadis-t-clip-system" rel="nofollow noopener">T-Clip System</a> by <a target="_blank" href="https://www.printables.com/@LineArcLine" rel="nofollow noopener">Line Arc Line</a>. You can also use <a target="_blank" href="https://www.printables.com/model/540362-skadis-t-clip-mini-parametric" rel="nofollow noopener">T-Clips mini</a> by <a target="_blank" href="https://www.printables.com/@capze_178225" rel="nofollow noopener">capze</a> or <a target="_blank" href="https://www.printables.com/model/472294-skadis-t-clip-system-low-profile-flush-mount-clips" rel="nofollow noopener">Low Profile T-Clips</a> by <a target="_blank" href="https://www.printables.com/@tchoupshop_82950" rel="nofollow noopener">tchoupshop</a> to fit flush. The clips come in two versions - one for black/white Skadis boards, and one for unpainted ones (not included here; please download from the creator).&nbsp;I made a <a target="_blank" href="https://makerworld.com/en/models/55181#profileId-56713" rel="nofollow noopener">T Clip tool</a> to make turning the clips easier, especially the <a target="_blank" href="https://www.printables.com/model/472294-skadis-t-clip-system-low-profile-flush-mount-clips" rel="nofollow noopener">flushed version</a>.

IKEA Skadis/ Skådis Filament Swatch Holder - T Clips

skadis

martin.taichl

This is my model of the Puddle Jumper from the Stargate franchise. It has retractable engine and weapons pods. No interior though. It is little bigger, but in scale with my gates.Here you can see a video about the project includin an assembly. Please ignore the colour differences on the model. It needs to be painted anyway ;) <div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=3eFA0s0bt1A"><iframe src="https://www.youtube.com/embed/3eFA0s0bt1A" frameborder="0" allowfullscreen=""></iframe></div>&nbsp;Enjoy.Category: Vehicles

Puddle Jumper from Stargate

modele

ILImy2024

This requires multiple colors of filament, you can mix and match your own colors.Print Profile 1 : This requires 3 colors of filament.Print Profile 2 : This requires 2 colors of filament. Print Profile 3 : This requires 2 colors of filament. Applicable to A1 mini. Print Profile 4 : Ironing type:Topmost surface only, Top surface:60 mm/s. This requires 3 colors of filament. Use when higher quality is required.

saturn 4

resin

p1s

skadis

modele

Gadżety