KYZ Design

Clayton Merkle

A universal cell phone mount which attaches to car seat headrest posts. &nbsp;When my daughter gets antsy on long car rides, sometimes we allow her to watch TV shows on my phone to keep her entertained. Until now, I always just held my phone up for her to watch, which was obviously less than ideal. She sits in a rear facing car seat, so I decided to design a phone mount to attach my phone to the headrest posts for easier and more comfortable viewing. This mount can also be attached to the headrests of the driver or passenger seat facing rearward for people sitting facing forward in the rear seats.&nbsp;This mount was designed to be easy to print and does not require any supports. I printed all parts in ASA so that they will withstand the hot temperatures inside the car in the summer. ABS and PETG may also work well. I recommend using at least 3 walls and moderate infill percentage to make sure it's nice and strong, especially in the phone ball mount.&nbsp;Only qty. 4 M3x8 screws are needed for assembly. Please do not over-tighten any of the printed nuts or the M3 screws to avoid damage. They just need to be snug. &nbsp;Note that the actual phone clamp portion of the model was heavily influenced by this model: <a target="_blank" href="https://makerworld.com/en/models/91888#profileId-98286" rel="nofollow noopener">swivel phone attachment for flexible & sturdy phone arm (100% Printed) Remixed by o Nubs - MakerWorld</a>, however my phone did not fit in it well, so I re-designed it from scratch using it as inspiration. Shoutout to @oNubs for his awesome model and the inspiration.

Universal Modular Car Headrest Phone Mount

Queue

Gridfinity baseplates completely remodelled from scratch, designed to minimise print time.<ul><li>Lower overall height (top trimmed)</li><li>Flares on the bottom removed</li><li>Smaller radii</li></ul>Designed for PLA and other materials with good first layer adhesion. You may need to add a brim to print with ASA/ABS. Print <a target="_blank" href="https://makerworld.com/en/models/76537" rel="nofollow noopener">these bins</a> next! <img src="https://makerworld.bblmw.com/makerworld/draft/285381/2023-11-28_4d90d07fb6c75.png">&nbsp;Check out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/26498" rel="nofollow noopener">this collection</a> for my other Gridfinity models andcheck out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/18964" rel="nofollow noopener">this collection</a> for my Honeycomb Storage Wall models.

Gridfinity Superlight Baseplates

Gridfinity - No Magnet

Originally posted <a target="_blank" href="https://www.printables.com/model/463601-hsw-feet-for-freestanding-walls-honeycomb-storage-" rel="nofollow noopener">here</a>, check it out to see past makes and comments&nbsp;These feet use the Ez-V1 series clip and therefore require no screws, are designed for easy printing, and print in the strongest direction.This will work with standard HSW wall pieces but if you are just having 1 piece, see this for <a target="_blank" href="https://makerworld.com/en/models/26738#profileId-26811" rel="nofollow noopener">single wall pieces with integrated frames</a>.&nbsp;If you print the feet with a fibre filled material (I used CF-ASA) and use it with one of the 10mm thick “HD” wall pieces as shown in the pic (which I printed in ABS+), it will be a very tight fit, but will not wobble and be quite secure.&nbsp;Check out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/18964" rel="nofollow noopener">this collection</a> for my other Honeycomb Storage Wall models andcheck out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/26498" rel="nofollow noopener">this collection</a> for my Gridfinity models.

HSW Feet for Freestanding Walls - Honeycomb Storage Wall

HSW Honeycomb Storage Wall - KYZ

Update 16/04/2024 - before printing, check out this <a target="_blank" href="https://makerworld.com/en/models/179426" rel="nofollow noopener">new model</a>!<h3> </h3><h4>Differences of the remix compared to the original</h4>Twist cap:<ul><li>Crossbar changed to nubs to increase vent area</li><li>Frame thinned from 2mm to 1.6mm to increase vent area and reduce print time</li><li>Vent wall thinned</li><li>Vent wall separated into a different STL to allow better control over pint settings in the slicer</li></ul>Main body<ul><li>Vent area diameter increased from 40.6mm to 46.8mm</li><li>Minor changes to increase internal capacity and reduce print time</li><li>Vent wall thinned</li><li>Vent wall separated into a different STL to allow better control over pint settings in the slicer</li><li>Version with slotted holes on the sides added - the extra venting allows the whole canister to be dried in a microwave or oven a little faster (doesn&#39;t make much difference inside a spool)</li></ul>Lock<ul><li>“Spool Lock Extended 16mm” added - to work with wider spools.</li></ul>Fitment tested on:<ul><li>Prusament spools</li><li>Bambu spools</li><li>eSun spools</li></ul>50% triangular infill works well for the vent walls.Import the main part and the mesh part together to make sure they&#39;re aligned.Mine are printed in Prusament ASA and seem fine when I put them in the microwave to refresh the desiccant.Ironing the top surfaces made a nice flat look! This model was originally posted <a target="_blank" href="https://www.printables.com/model/581396-desiccant-spool-tumbler-airflow-remix" rel="nofollow noopener">here</a> on 14 September 2023.&nbsp;If you have Bambu spools, you might be interested in <a target="_blank" href="https://makerworld.com/en/models/72591" rel="nofollow noopener">this one</a><figure class="image image_resized" style="width:58.46%;"><img src="https://makerworld.bblmw.com/makerworld/draft/860911/2023-11-24_4ec6b865eb83f8.jpg"></figure>

Desiccant Spool Tumbler - Airflow Remix

Print Station

Holders for solar garden lights.&nbsp;Mounts with 2 gauge 6 screws.&nbsp;Suggest printing in ASA or PETG.&nbsp;Model has built in partial brim - to help with ASA adhesion.

Garden Light Holder - For Solar LED Lights

Garden

Walls and infill % depends on your material and requirements.Mine in the photo is printed in PLA, 0.4mm nozzle, 4 top, 4 bottom, 3 walls, 15% triangular infill.Corner brace designed with the advantages and disadvantages of 3D printing in mind. (Most other brackets are designed to mimic what a CNC machined bracket would be, or wood joined together!)

Queue

Gridfinity - No Magnet

HSW Honeycomb Storage Wall - KYZ

Print Station

Garden

Workshop Hardware