Jocika

RemcoGoy

Original model; https://www.printables.com/model/427403-double-layer-rugged-multipart-pinecilts100ts80-cas&nbsp;Print both files from this model, the rest of the files can be used from the original model.&nbsp;If you have any question, feel free to contact me.

Larger Bottom Insert for Rugged TS100/Pinecil/TS80 Case

Elektro Dinge

YGPark

Contains all optional files. Choose a form that suits your condition and print it out!!&nbsp;&nbsp;>Function1. Additional exhaust fan If you turn on the left switch, the LED lights up continuously The exhaust fan can be switched on, off and speed controlled using the exhaust motor controller next to it. However, since it is a low-cost motor, it only works when a certain voltage is applied.. It needs to be about 85% of the controller to start spinning. Subsequently, fine movement will adjust the speed. I bought another speed control fan because of the speed control part, but it was in the same condition, so I just finished with this product. (It took about another week because of this.) TT As another solution, mark2 is planning to add a temperature change sensor to allow the exhaust fan to operate and stop automatically without adjusting the speed.2. 2. LED Low-heat LEDs were applied to prevent them from breaking down under the influence of internal temperature, and for even light distribution, they were applied at a 20 degree angle. 0.76w x 6 pieces = 4.56w per piece.3. a thermometer The temperature of the upper part of the chamber can be checked by applying a needle-type thermometer. (You can take it out while cooking.)4. You can adjust the right lever to adjust the amount of heat exiting the rear top exhaust. Due to the strong performance of the additional fan, the hole was not made large to maintain the temperature inside the chamber.5. window partition vent It's a size that fits my fancy. I attached the f3d file, so you can pull it out according to the height of your window frame Even if you increase the chamber fan speed to 100%, the air suction snout is at the height of the extruder, so you can't suck the hot heat above that. In particular, the PLA is vulnerable to heat, which requires opening and printing the front door, so adding an outlet at the top allowed the door to be closed and output.It was built within 60mm to make the most of the space behind the printer.The temperature at the top of the chamber was maintained at 46-48 degrees. We are planning to match this part by applying the temperature sensor at mark2.The outlet plug is foreign, so it's thin, so it doesn't get tight. It's a good idea to exchange products that you throw away at home or on the radio. Or wrap it with tape so that the plug doesn't come offAll options are modular, so you can select and install only what you want. If you don't need an LED, you can take out the frame and print it out If you don't need a thermometer, don't plug it in~ To install the additional fan on the window side rather than behind the printer, pull out the 100mm external diameter and 100mm internal diameter adapter, respectively, and move them again. Since the fan controller (FWM) is not functioning properly, you can only turn it on and off without a controller.The AMS is designed so that it does not affect the bending of the rear tube even when setting is placed on the printer. >Main points when assembling It is recommended that you lay it on the floor first and then put it on the chamber. 1. Plug the power on/off switch into the fan's wire first to hold the line length. Connect the wiring as shown in the picture. Fan = Plug-Switch-Controller-Pan LED = Controller-Inverter-LED Pass the wires from the switch and the wires from the inverter in one place. Hand over the wires to the fan to the other two slots. The wires are relaxed, so don't make them too tight. If you fold the spare parts into the frame later, they will be neat. 2. Pull and pull the controller adjustment knob, assemble it to the case, and plug the knob back in. 3. Never cut the wire and adjust the length with LED wires as it has holes to match the length of the inverter's wiring~ 4. Use the 'Tree' support when extracting the vent3 file and carefully remove the parts when removing the support. 5. Insert the magnet by setting 'Pause' by pressing the right mouse button at the first layer where the hole is covered in the preview slicing state. 6. The Extruder Tube Guide must be installed. https://www.printables.com/model/338542-x1-p1p-ptfe-tube-guide-to-fix-loading-issues-best-&nbsp;> Purchase ListController https://ko.aliexpress.com/item/1005004180917280.html?spm=a2g0o.order_list.order_list_main.23.5faa140fPiDN3o&gatewayAdapt=glo2kora blast fan https://ko.aliexpress.com/item/1005004354219502.html?spm=a2g0o.order_list.order_list_main.58.5faa140fPiDN3o&gatewayAdapt=glo2korLED / Inverter Epoxy type 3-hole module KPL Korean 30w (165x24x18mm)neodymium magnet Magnet size: D15Xd7.3X15TThermometer Advanced Cooking Thermometer (Automatic Off after 10 minutes) https://ko.aliexpress.com/item/1005002322143988.html?gatewayAdapt=glo2kor - Hardware store bellows duct 100 mm Cable ties (or anything you can tie to your house or electrical tape)

Vent for P1S by YGP

Bambu X1C

braga3dprint

Elevate your Xiaomi Electric Scooter Mi 3's style and protect its deck from scratches with this 3D-printed accessory. It's designed for easy printing in PLA material and requires no supports, making it hassle-free to share and use.Key Features:<ul><li>Aesthetic Enhancement: Give your scooter a unique look that stands out.</li><li>Scratch Protection: Keep your scooter's deck looking new by preventing scratches.</li><li>Easy 3D Printing: Print it effortlessly without the need for complex tools.</li><li>Durable Material: PLA works well, but consider PETG for outdoor use.</li><li>Customization: Paint it post-printing or use color changes during printing.</li></ul>Upgrade your Xiaomi Electric Scooter Mi 3 with this 3D-printed accessory, and ride in style while keeping your deck protected. Share it with the community to spread the love!

Xiaomi Electric Scooter Deck Accessory

Xiaomi Roller

schiko

Remix of <a target="_blank" href="https://www.printables.com/model/258431-rugged-box-parametric" rel="nofollow noopener">Whity's Parametric Rugged Box</a> (Printables).&nbsp;You need:<ul><li>6 M3x30 screws</li><li>4 608 ball bearings</li><li>1 PC4-M10 quick fitting connector</li><li>1 rectangular hygrometer (the cheap one)</li><li>a bit of PTFE tube</li></ul>The tray has to be printed in a flexible material, e.g. PETG, the seal needs to be very flexible (TPE/TPU), for the other parts PLA is okay.All parts printed with .4-nozzle, .2 layer height, no supports. The bars have to be printed with 9 walls or 100% concentric infill.I used hot glue to fix the hygrometer to get it airtight.&nbsp;I originally posted this model at <a target="_blank" href="https://www.printables.com/model/498283-rugged-filament-dry-box-for-over-200g-silica-gel" rel="nofollow noopener">Printables</a>.

Elektro Dinge

Bambu X1C

Xiaomi Roller

Filament Dryer