Joachim

ManOwaR

I have created a ground screw for attaching the charging station or for the garage of my Husqvarna 315X.It is identical to the supplied ground screws, of which unfortunately too few were included.&nbsp;I printed them in the Bambuslicer with the "Strength" profile. I lowered the speed a little!&nbsp;<ul><li>Layer height 0.20mm</li><li>25% filling</li><li>6 wall lines</li><li>Exterior wall 60 mm/s</li><li>Inner wall 200 mm/s</li><li>PETG</li></ul>

Husqvarna ground screw for robotic lawnmower charging station and garage

robot lawn mower

garrett1966

Custom made wall mount bracket to easily hang up and store your 4.5" angle grinder securely.&nbsp;Designed for the Milwaukee M18 Fuel grinders but will probably fit other brands as well.&nbsp;<a target="_blank" href="https://garrett3dprints.etsy.com/listing/1673091907/milwaukee-m18-fuel-45-angle-grinder-wall" rel="nofollow noopener">Available from my store on Etsy</a> as well if you don't have your own printer

Milwaukee M18 Fuel 4.5" angle grinder wall mount

Tool holders

ThreeD-Michael

This is version 2 of my “Smartphone Tripod Adapter”. It has been improved in two main points:<ul><li>the center of gravity of the smartphone is now directly above the fastening screw, which gives the tripod a more secure stand,</li><li>the tripod adapter is now even more compact and lighter.</li></ul>Description:This tripod mount can hold almost all smartphones with its clamping range of 64 to 84 mm. It can easily be printed as a single part (“print-in-place”). No other components are required other than a rubber band. For smartphones with slippery sides without a case, self-adhesive silicone bumpers can optionally be glued in.&nbsp;Printing Instructions:Use a 0.4mm line with a layer height of 0.2mm. Print the object in the specified orientation. If possible, place the Z-seam as shown in the image above.&nbsp;Assembly Instructions:Before using the adapter, the assembly of one or two rubber bands is required. Using two rubber bands instead of a single one can increase safety. Smartphones with silicone cases usually hold well. For smartphones with slippery sides without a case, recesses have been provided into which optionally cut self-adhesive silicone bumpers with a thickness of 2 mm and an edge length of 7 mm can be glued (see pictures above).&nbsp;Instructions for Use:Before inserting the smartphone, please check whether the rubber band(s) are still intact. The smartphone could fall out if the rubber band(s) break. The adapter has a printed thread to accept the mounting screw. This printed thread can wear out. Check the screw connection for tightness.

Smartphone Tripod Adapter V2

Mobile phone accesory

mojo哒哒哒hhh

This magazine can be used on HK 416/MR556. like PMAG &nbsp;&nbsp;

5.56 nato mag  for Hk416/MR556 like PMag

Philip Army

3D Print Masters Hub

Mini Stackable Bins with Optional Nameplates<ul><li>Internal bin size 100mm x 56mm (4&#34;x 2.25&#34;)</li><li>Choose optional nameplates: Blank, Bolts, Screws, Nuts and Bambu Logo</li><li>Scale up as needed</li><li>3MF file configured to print with 3 walls.</li></ul>Please like and subscribe! More to come!🔥🔥 Check out my PRO MODELS HERE! <a target="_blank" href="https://cults3d.com/en/users/FabulousFilaments/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/FabulousFilaments/3d-models</a> 🔥🔥

Mini Stackable Bins with Optional Nameplates

Storage

xiangyucao

<h2>Extremely loud and compact emergency whistle</h2>

Extremely loud and compact emergency whistle

Toys

Manicken.se

I&#39;ve noticed that most trash bag roll holders out there can only handle one roll at a time. But since I usually buy them in bulk, I wanted to create something different, a holder that can handle multiple rolls. As seen in the pictures, this one can hold up to three of my rolls! It&#39;s got two parts that you can space out however you like to fit longer rolls. And it&#39;s designed to fit rolls with a max diameter of 62mm. Plus, setting it up is a breeze – no screws needed, just stick it on with some double-sided tape. Easy peasy! I also have a one roll version linked below. If you appreciate my work, please consider giving it a like. For those in Sweden, feel free to explore my webshop at <a target="_blank" href="https://manicken.se/" rel="nofollow noopener">manicken.se</a>.Have a fantastic day! 😊 Or! Check out my other models:  <figure class="table" style="width:96.85%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><a target="_blank" href="https://makerworld.com/en/models/415520" rel="nofollow noopener">Trash Bag Holder Tape / Skådis / Screw / Skådis</a></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837243/2024-04-09_577ad1c4f7867.jpg"></figure></td></tr><tr><td><h4><a target="_blank" href="https://makerworld.com/en/models/226646" rel="nofollow noopener">Post-It Stencil | Squares and Circles</a></h4></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837243/2024-03-15_6c3987a33c6f9.jpg"></figure></td></tr><tr><td><a target="_blank" href="https://makerworld.com/en/models/226698" rel="nofollow noopener">Dyson V15/V11/V10/V8/V7 Wall Mount</a></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837243/2024-03-15_37a2ae5b98687.jpg"></figure></td></tr><tr><td><a target="_blank" href="https://makerworld.com/en/models/373557" rel="nofollow noopener">Bottle Dryer With Lid Holder</a></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837243/2024-03-15_281c177b22d81.jpg"></figure></td></tr><tr><td><a target="_blank" href="https://makerworld.com/en/models/226749" rel="nofollow noopener">Jewelry Holder | Wall Mounted</a></td><td><img src="https://makerworld.bblmw.com/makerworld/draft/837243/2024-03-15_6fff9ef39900a.jpg"></td></tr></tbody></table></figure>

Multi Trash Bag Roll Holder

House

Lolcio

To mark a center, or cross cut, you need to print, two pins.Pins should be printed with 100 infill.

Square, Center Scriber, Edge Marking Tool, Ruler

Gauges

PartyLime

GEN 12: please see my profile for the GEN 12 ball. There&#39;s a limit of 500mb on one page so I had to make another for the latest Gen. It bounces really well and feels super durable in TPC I wasn&#39;t satisfied with the current models of the airless basketball on here as they only had a single lattice. This took me days make sure the double lattice worked in CAD - SolidWorks was not built for this! As I don&#39;t have $2,500 to spare, I worked from the images available online.I printed it in TPU. It doesn&#39;t bounce as much as a standard basketball in TPU so I suggest a stiffer material.&nbsp;GEN 9: I have added a gen 9 version. It is a little closer to the original and should weigh about the right amount when printed in TPU/PLA&nbsp;GEN 10: I have adjusted the size of the hex holes and increased the filled on them. I&#39;ve also increased the lattice thickness to 8mm to hopefully increase bounce. The logo on the top and the airless gen 10 tag have also increased in size a little to improve how they look. Lastly, the holes around the seam are now pentagons as in the original ball&nbsp;GEN 11: I have added a new version with cut-outs throughout the seams. This will hopefully make the bounce more consistent.&nbsp;The original version I uploaded was removed due to “abnormal download data”. MakerWorld support took all my points but said I could re-upload so here it is again. Hopefully that won&#39;t happen again. MATERIALS:Extrudr Hard TPU (58D) - good durability about 40% bounceOverture Super PLA+ - 100% bounce but broke easilyOverture easy nylon (PA6) - broke almost instantly (the community have suggested “annealing” the print in water to increase durability)BASF Forward AM Ultrafuse TPU 64D - good durability and 60% bounce (BEST SO FAR)BASF Ultrafuse TPC 45D - good durability and great bounce. I recommend annealing this one at 110°C for 10 hours at least.

Airless basketball

Games

3DMN

The housing fits LCD 16x2 2x16 model BIG LCD-PC-1602B-BIW

16x2 BIG LCD Case

cases

CopyKnight

LED Lichtring&nbsp;dieser Lichtring, wurde für einen LED Streifen entworfen, der mit 3 AA Batterien betrieben wird. (Diesen gibt als 1 Meter es für 1,50 € bei Action in warmweiß)&nbsp;Beim Zusammenbau sollte der LED Streifen durch die löcher geführt und eingeklebt werden. Der Ring Part A und B, nachdem der Diffusor zwischengesteckt wurde muss dann mit 2 Sekundenkleber an entsprechender Stelle zusammengeklebt werden.&nbsp;Lediglich die Box benötigt Support. ansonsten alles normal mit 0.2 Layerhöhe drucken. PET / PLA / ABS egal. Alternativ kann der Diffusor auch mit TPU gedruckt werden. (muss aber nicht)&nbsp;&nbsp;LED light ring&nbsp;This light ring was designed for an LED strip that is operated with 3 AA batteries. (This is available as 1 meter for 1,50 € at Action in warm white)&nbsp;When assembling, the LED strip should be guided through the holes and glued in. The ring part A and B, after the diffuser has been inserted, must then be glued together with 2 superglue at the appropriate point.&nbsp;Only the box needs support. Otherwise print everything normally with 0.2 layer height. PET / PLA / ABS does not matter. Alternatively, the diffuser can also be printed with TPU. (but does not have to be)Translated with DeepL.com (free version)