Jonathan

9mm diameter, 10 mm usable length

Screw replacement (push-in pin with lock)

Ready to print (3 plates for different color print)

Ready to print single plate (1 color)

Spirograph

Cat tail Bookmark

Draft mode to save filament, 10% infill

Blank version

English version

Poodle christmas ornament

0.24mm layer, 2 walls, 10% infill

Merry Christmas version

Rottweiler christmas ornament

0.16mm layer, 2 walls, 10% infill

Christmas Wreath bookmark

Christmas tree bookmark

0.08mm layer, 2 walls, 10% infill

taller middle part

Hummingbird bookmark

Snow flake bookmark, 0.08mm layer, 2 walls, 8% infill

Snowflake bookmark

Flying dove bookmark

0.08mm layer, 2 walls, 8% infill

Small multi organizer for pens 0.24mm layer

Inverted L shapped organiser 130 mm x 210mm 0.24mm layer

Two long compartments 210 mm X 130 mm (50mm + 80 mm)

Multi compartment (1 Lg, 2 med) 210mm x 140mm

Single compartment 50 mm x 210 mm

Drawer organizer simple and bottom less

Draft mode, separated version for fewer supports

Drawer rail

Draft version for increased speed

One piece, draft mode, harder to remove supports

Sliding rail divided, draft mode for speed

Peg and/or handle glued

under desk container

Draft version for speed (open printer door and pieces fan)

Straight version

Cabinet kick handle

Cute Axolotl decor  0.16mm layer, 9% infill

Axolotl flat decor

0.24mm layer, 2 walls, 15% infill

Latrax Teton rear shock tower #7637

0.08mm layer, 2 walls, 15% infill

Hockey goalie mask

reorganized for better fitting on book V3

0.2mm layer, 2 walls, 15% infill

Tall version 

Rottweiler bookmark

BEN 3D

MECHANICAL ROCKER LIGHT SWITCH COVER

0.2mm layer, 2 walls, 10% infill

absolutly and marvelously useless. 😆But still really well done.

Rexi Labs

Legendary Mk2 Pineapple Grenade with Flying Handle

Printed Plastic Spring (prototype, see description)

Vixvvo3D

Modern UnderDesk Drawer

Body Drawer

printed well and easily. Used bambu jade white in extradraft mode

llama492

Lump O Coal

0.2mm layer, 2 walls, 8% infill

LeHa Design

Golden Snitch Ornament Ferrero Rocher Holder

golden snith orb 0.12 fine w.Supports

easy print with the minimal amount of supports. Nice use of support blocker.

wings 0.2mm OuterWallFirst

prints very well and fast. Glue free assembly is a nice touch too.

Nyg By Design

Super Mario Star - Christmas / Holiday Tree Topper

P1 X1 Version (CoreXY)

SH Designs

Twisted Temple Game

very nice board game. Lots of bits for small kids tough. I would rate it 5+ years. 

Ace3DPrints

EGO Edger & String Wall Mount Holder

0.28mm layer, 3 walls, 20% infill

Craft3D Studio

Cute Axolotl Keychain

0.16mm layer, 2 walls, 15% infill (2 layers)

Very nice model! Made a remix without the keychain hole to use a wall decor.
Thanks

Nico

Triple skull wearable mask (2 parts)

0.2mm layer, 3 walls, 15% infill

Very ugly! That's the point ;P 
Had some issues removing supports in the pin holes. Due to Lightning infill the flat part was not tightly secured and it came out while I was pulling the support out. I eventually repared it by glueing everything together, but I suppose that an other type of infill would make it stronger, but heavier. Also, one of the pins is going through the mask and is visible..... Good job

Tommy Gun

Katana V2 Samurai Sword Pip dual color no ams

0.2mm layer, 2 walls, 5% infill

Very nice quality. I would suggest to add a locking mechanism of some kind to prevent the blade to get out of the handle. I used a piece of foamed tape inside the handle to tighten it inside. Also, would suggest to increase to number of layers and infill % for the bottom part of the handle as it broke of after a couple of in and out.
That's my two cents ;) Good job for the design, very nice! 

BATTCAVE

Large Demon Skull Halloween Candy Bowl 

X1C - 0.2mm layer, 3 walls, 10% infill

I used standard supports for ease of removal. E-sun bone white and burnt titanium from FF SUNSENKJ. Really great print will boost again for sure.

planpa3d

Mario Boo Ghost

Optimized (High Quality)  0.12

Billy Hooper

The Skull of Frankenstein

Very nice design. But I really suggest to use Support for PLA filament. Spent 2H removing them and I'm not done Yet!!!

rleetrucking

Slow Bowl

PETG print. Printed very great!! Added four legged companion's name on the side of it.

johnDangle

V3 Classic Dice Tower- Print In Place, No Supports

OPTIMIZED 0.16mm layer, 3 walls, 8% infill

Awesome print! Nice details, good design to eliminate supports. I'm amazed.

Magic Studio 3D

Bitcoin (BTC) - Coin

A1 Mini Compatible - Multicolor Capable - 0.2mm layer, 2 walls, 15% infill

Good and easy print! with good printing quality.

idealoding

Aztec gold coin

0.28mm layer, 2 walls, 15% infill

Excellent and easy print! Printed at 45mm diameter. The details still worked very well. Used Bambu Black and Gold PLA with AMS.

cmcraig2

Standard Caliper Hanger for Hex System HSW

Works very well for the caliper I ordered on Amazon