J0n550

blecheimer

Hey Wastelander!Do you want to get rich? But collecting bottle caps is taking too long? Wanna get rich fast? Then just download my model and print your own bottle caps! What does this shortcut to riches cost, you might ask? Nothing, it is for free. But leaving a &#34;boost&#34; for an old designer is very much appreciated. ;)&nbsp;This is a Nuka-Cola bottle cap from Fallout. It is designed to be printed with an AMS system in two colours. For best results an 0.2mm nozzle is recommended though it can be printed with an 0.4mm nozzle as well. But the 0.2mm version has a sharper look and the logo does not appear to be so washy. Take a look at the pictures and judge yourself what is better.But wait - do you want a bottle for that cap? No problem, <a target="_blank" href="https://makerworld.com/en/models/438005" rel="nofollow noopener">here is my Nuka-Cola bottle</a> that perfectly matches the bottle cap.And for the collectors out there, <a target="_blank" href="https://makerworld.com/en/models/446415" rel="nofollow noopener">here is the Nuka-Cola Quantum bottle &amp; cap</a>.&nbsp;EDIT 2024-04-23: Some users had bed adhesion problems with my 0.4mm print profile. It seems that my first layer setting of 0.1mm height was too aggressive. I changed it back to standard in the print profile. Fingers crossed, that this will help.&nbsp;Print preparation: Make sure that your print bed is clean and grease-free. An unsufficient bed adhesion is in most cases not a problem of the print profile but a cleanliness issue. If you want you can use glue on your print bed but for PLA this should not be necessary. If possible use the smooth textured PEI plate and a bed temperature of 55-60°C. For the print quality it is important that you use a good and calibrated filament. Know your k-factor and use the correct flow setting. Bambu filament makes this step easier but any other quality brand will do the job.&nbsp;Print settings: For a 0.2mm nozzle use the 0.06mm High Quality settings and change the initial layer line width to 0.12mm. Yes, this is smaller than the nozzle but it will work and give you all the fine details. The wall generator should be set to &#34;Arachne&#34;. For the surface patterns I recommend using the concentric version as it has a nice finish. If you want you can reduce the printing speed a little bit to optimze quality. For the same reason I am using a small prime tower.With a 0.4mm nozzle use the 0.12mm Fine settings but set all layer heights after the first layer to 0.1mm. The first layer should stay at 0.2mm height. The initial layer line width must be 0.21mm otherwise the logo will be a mess. The rest is the same as above: Arachne wall generator, concentric surface patterns, slightly reduced speed and a small prime tower.&nbsp;For more detailed print settings take a look at my print profiles. The print profiles can be used with A1, P1 and X1 printers. And now go and print yourself a fortune before the brotherhood finds out!&nbsp;If you want to support me you can leave a tip at <a target="_blank" href="https://ko-fi.com/blecheimer" rel="nofollow noopener">ko-fi.com/blecheimer</a>.&nbsp;&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="https://creativecommons.org/licenses/by-nc-nd/4.0/" rel="nofollow noopener">CC-BY-NC-ND 4.0</a>. The shown model is fanart and must not be used commercially. Copying this model to other 3D printing websites is not allowed without my permission.

Nuka-Cola Bottle Cap (from Fallout) 

want to print

everydaynormalguy99

I made this keychain from an svg file from the internet, printed in two colors on a P1S with AMS, it has three color changes Print in PLA

Jesus Keychain

Nyckel ringar

eier1188

Cute Skull and crossbones earrings I made.&nbsp;These are meant to be combined with an earring hook and jump ring, a 6mm OD jump ring is necessary, a 5mm OD will work too, 4mmOD is very difficult but doable. Either way the jump rings may be difficult to attach, I didn't want to print a loop but that made the jump ring attachment more difficult. You will need needle nose pliers.&nbsp;Also to be used with a .2mm Nozzle, otherwise much of the detail is lost, but still doable with .4mm&nbsp;The print pauses twice to switch colors1st color is white, 2nd is black, 3rd is red&nbsp;UPDATE 1/12/24: If printing with a .4mm nozzle change the inner and outer walls to .25 and it should print that black outline pretty well, if not then you can mess with those settings, I've gone as far as .2 on all the line widths and been fine.&nbsp;These models take time and work to get right, I do this for fun and not business but if you want to support me or show gratitude and buy me a coffee I'd be Extremely grateful! <a target="_blank" href="https://www.buymeacoffee.com/eier" rel="nofollow noopener">https://www.buymeacoffee.com/eier</a>&nbsp;&nbsp;Let me know if you have any requests, Thank You!

want to print

Nyckel ringar

Örhängen