Imperator_1972

Lukas

Easter window pictures

easter

DoubleT

Added versions for - Holder for 6mm belts and 3mm backer behind extrusion - Holder for 9mm belts with and without backer

VORON AB Belt Installation Helper (Clamp)

Voron

Brandon Raineri

<h2>Updates</h2><h3>Version 2.1 (09/27/23)</h3><ul><li>Added lead-ins to the filament entry cavity</li><li>Changed PTFE stop ledge angle at filament exit end</li><li>Added note about countersinking PTFE that enters the printer</li><li>Updated printing profiles</li><li>Added additional sources for the release rings so they can be purchased outside of the US</li></ul><h3>Version 2</h3><ul><li>Added through hole for an M3x20mm mounting screw. Printed with a 0.4mm nozzle at 0.10mm layer height</li><li>Added printable locking clip STL file to eliminate backlash in fitting/PTFE tube when pulled on</li><li>Print with single inlet side on the build plate. Add a 10mm brim to stabilize the print</li></ul><h3>Version 1</h3><h2>Background</h2>This allows you to run material from the AMS or external spool without having to disconnect the PTFE tubing.This uses push to connect fittings as you would see in a typical PTFE connector.&nbsp;<h3>Release Rings: QTY: 3 of PC4-UM2</h3>I do NOT recommend the printed release rings as they are too fragile and do not securely hold the PTFE tube into place.&nbsp;Amazon (<a target="_blank" href="https://www.amazon.com/dp/B0B282NZVW?ref=ppx_yo2ov_dt_b_product_details&th=1" rel="nofollow noopener">https://www.amazon.com/dp/B0B282NZVW?ref=ppx_yo2ov_dt_b_product_details&th=1</a> )AliExpress (<a target="_blank" href="https://www.aliexpress.us/item/3256804490680277.html?gatewayAdapt=glo2usa4itemAdapt" rel="nofollow noopener">https://www.aliexpress.us/item/3256804490680277.html?gatewayAdapt=glo2usa4itemAdapt</a>)McMaster (<a target="_blank" href="https://www.mcmaster.com/5472K101/" rel="nofollow noopener">https://www.mcmaster.com/5472K101/</a>)<h2>Installation</h2>Push the retaining ring into each end. After you insert the PTFE tubing until it bottoms out, pull back so the release ring has a gap between it and the printed surface. Insert the locking clip into this gap and then push the PTFE back in so it seats. This removes any backlash so the end of the PTFE tube remains firmly in contact with the bottom of the bore.&nbsp;While not always required, I found it helps to countersink the PTFE tube entering the printer as it provides a lead-in to prevent snags.&nbsp;You also need to ensure the printer buffer operates as intended. The PTFE tube exiting the buffer needs to clear the AMS clip going into the back of the printer. This prevents any unwanted resistance to the buffer and let‘s it operate as intended. If not, you can see what looks to be like a partial clog or even failure to retract filament.

Over-Engineered Y-Splitter

Bambulab_Upgrades

m.parts.3d

Pin Car Replacement

Auto

laisch

A potato slicing tool to make nice potato spirals for the deep fryer.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/254793/2023-12-11_i5v5y18u25ek.jpg"></figure>&nbsp;&nbsp;Printing:The cutter is printed in PLA with 0.16 mm layerheight The handle is printed in PLA with 0.2mm layerheight&nbsp;Usage:You need a metal pike with 2mm diameter.<ul><li>Put the slicer onto the pike with the screw facing down.</li><li>put the potato on the pike</li><li>put everything onto the handle</li><li>now turn the screw into the potato and slice it all the way</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/254793/2023-12-11_2mioj0df0jw5.gif"></figure>

Potato Spiral

Kitchen

HribaDesign

The containers are composed of one or more hexagons with a basic size of 5 cm.All are available with a smooth or wavy bottom.

Catch-All Trays / Hex organizer

deko

evax design

It is a decoration designed to decorate a cake. It's very simple. It is 14 cm high, 20 cm wide and 0,4 cm thick. Please refer to the printing instructions before printing. The model can be proportionally scaled up or down, but you need to add or subtract the height of the layers!Printing instructionsThe print orientation should be placed on the mat with the flat side facing out. It is designed to be printed without backing. Print with a layer height of 0.2 and a nozzle of 0.4 and with 100% fill and 2 perimeters.Translated with www.DeepL.com/Translator (free version)

Happy Birthday pinprick

Happy Birthday

DeepSouth3DPrints

Standing Grinch Door Corner!UPDATE:(I've uploaded two more print profiles for the model to be printedFace Down on the build plate which will give the model a clean textured lookwhen using the gold pei plate!)&nbsp;I uploaded both the right and left print profile versions.Please give it a like! It helps getting noticed forothers to enjoy. Thanks andMerry Christmas!&nbsp;You can find my other Christmas decorations <a target="_blank" href="https://makerworld.com/en/u/1201824007/collections/122929" rel="nofollow noopener">here</a>

Standing Grinch Door Corner

Christmas

Glas Separation without Riser

X1C riser without AMS bracket and drawers / X1C riser ohne AMS Halterung und Schubladen

Drawer Handle for Vixvvo 3D´s Desk Organizer

cat