Search models, users, collections, and posts
Bio
Controls Engineer by profession, including Industrial Automation, Instrumentation, hardware and software design, build, install, commissioning, and sustainment.
Home hobbyist machinist, rebuild machines for my own use to keep them from the scrap yard. 3D modeling for rapid prototyping to support my hobbies.
Achievements
MakerWorld Guardian
This badge has expired
This is a hose adapter for a Hercules Dust Collector Vacuum to a Vac-U-Guard surface grinding wheel guard. This is made to fit to the dust extractor hose directly without the need for the nozzle.
Hercules Dust Collector Hose Vac-U-Guard Grinder
1
3
Share
0
0
0
I needed a replacement Nozzle Tip for Capri Tools Adjustable Air Blowgun so I created this model. This is meant to be nonmarring in case the blow gun comes in contact with anything that can easily be scratched. This may fit other air blow guns with a 6mm outside diameter.
Nozzle Tip for Capri Tools Adjustable Air Blowgun
5
6
Share
0
0
0
Just what I needed. Works great and looks great. I printed it at a 45 degree angle so the layer lines were not parallel with the camera mounting tabs/rails.
Share
0
0
0
Just what I needed. Works great and looks great.
Share
0
0
0
Just what I needed. Works great and looks great.
Share
0
0
0
Nice model! Prints well and looks good.
Share
0
0
0
This works pretty well. I had to scale it up to fit the brushes I am using.
Share
0
0
0
Just what I needed to organize my desk. :)
Share
0
0
0
Looks good, prints good, and works well. :) Just what I needed to organize my office. Much better than laying the headset on the desk.
Share
0
0
0
I wanted a way to keep dirt, grim, dust, and mud out of my Milwaukee travel mug when off-roading in a Polaris RZR side-by-side UTV. Offroad tends to throw dirt, dust, and mud all over the place and it ends up on top of my Milwaukee mug. This model covers the travel mug to keep debris out so I am able to take a drink of coffee, tea, or whatever else is in the mug without getting a mouthful of dirt.
Milwaukee Travel Mug Lid Dust Cover
2
12
Share
0
0
0
I needed to join two 6" dust collection hoses together, so I developed this model and printed it.
Dust Collection Hose Adapter Coupler - 6"
3
15
Share
0
0
0
I needed a way to join two 4" dust collection hoses together, so I worked up this quick design.
Dust Collection Hose Adapter Coupler - 4"
3
13
Share
0
0
0
Nice hook. I had to use supports as the underside is radiused. otherwise I was having bed adhesion issues until I enabled supports.
Share
0
0
0
Prints great, works great. Thank you for this.
Share
0
0
0
Prints great, works great. Thank you for this.
Share
0
0
0
Prints great, works great. Thank you for this. I printed this at a 45 degree angle to avoid the layer lines being parallel to the mounting tabs/rails. Previously this print would break at the layer lines when printed flat.
Share
0
0
0
Prints great, works great. Thank you for this.
Share
0
0
0
I thought I could make better use of the two pre-existing tool holder holes on the Park Tool PCS-10.3 Bike Maintenance Stand than Park Tool did. This new tray will hold five tools and has a magnetic parts tray holder. AlI'd say that is an improvement.
Park Tool PCS 10.3 Magnetic Tray & Tool Holder
3
32
Share
1
0
0
Model did not fit my older 1960's era Bridgeport Series 1 head. My mill is 100% OEM Bridgeport. I had to tweak the design a bit, but made it work.
Share
0
0
0
Works as intended, printed well.
Share
0
0
0