IT-Pro

SigmaT4

Concept:A ring box where the ring moves in a helical motion when opened.No hardware needed.There are two versions:<ul><li>One with a heart able to lock on a ring</li><li>One with a flat heart, where you can engrave your desired text.</li></ul>This model was designed for the Saint Valentin's contest.&nbsp;You can find the ring herehttps://makerworld.com/en/models/182128#profileId-200649&nbsp;Print files:The included 3mf should work absolutely fine with Bambu Lab printers. There are two plates:<ul><li>One with the case (base & lid), the top cover, sliding tray and two clips.<ul><li>I printed this plate in overture wood PLA</li></ul></li><li>One with the helical heart with its guide (printed in place) and the slider (locking the ring).<ul><li>I printed this plate in red eSUN PLA+</li></ul></li></ul>Assembly:<ol><li>The heart and the guide are “print in place”. Twist the guide to break it loose. (it should revolve freely inside the heart)</li><li>Pressfit the guide onto the sliding tray (look for a dent in the tray)</li><li>The lid has two pins which must slide into slots in the tray. You must now have an assembly with heart, guide, tray and lid</li><li>Insert this assembly into the base. Note : Make sure the heart is initially inserted facing you. It will twist and face away when it goes down.</li><li>Insert both clips to secure the lid.</li><li>Install the cover to hide the mechanism. It pressfits on the base.</li><li>Install the ring and lock it in place with the slider</li></ol><figure class="image image_resized" style="width:54.39%;"><img src="https://makerworld.bblmw.com/makerworld/draft/524525/2024-02-11_c0fc5b111a04c.jpg"></figure><figure class="image image_resized" style="width:54.16%;"><img src="https://makerworld.bblmw.com/makerworld/draft/524525/2024-02-11_6cba86ee6b6da.jpg"></figure><figure class="image image_resized" style="width:53.91%;"><img src="https://makerworld.bblmw.com/makerworld/draft/524525/2024-02-11_a9ca69696fc27.jpg"></figure><figure class="image image_resized" style="width:53.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/524525/2024-02-11_dd2dbace530a9.jpg"></figure>&nbsp;Note if you want to slice the files yourself:<ul><li>To minimize friction, the base and tray must be printed in an orientation leading to layer lines being orthogonal. If you print the tray flat, the print lines will be parallel which rub.</li><li>Avoid printing the lid flat on the bed. The lid “legs” could be too fragile.</li><li>As there is tight tolerances (to allow smooth sliding) please use (“outer/inner” wall order).</li><li>I recommend enforcing support for the pins of the lid.</li></ul>I am cleaning up my source files, and I will post the link soon. (I designed everything on Onshape).If you are interested, please leave a like J

Ring box, with a twist

Proposal

Keyline Studio

DIY Monkey LED Lightbox for 3D Printing Enthusiasts&nbsp;Bring a playful jungle theme to your child’s bedroom with our DIY Monkey LED Lightbox. This delightful design is ready for you to 3D print and personalize for your little one’s space. The charming monkey silhouette is expertly designed to cast a gentle glow, perfect for a nightlight or a whimsical accent piece.&nbsp;Features:<ul><li>Replaceable front plate: Compared to other lightbox design, this one allows the replacement of the front plate in case it gets damaged or just if you want to print it in other colors</li><li>Customizable: Compatible with a 1-meter USB LED strip</li><li>Child-Friendly Design: Soft, diffused light ensures a dreamy, not-too-bright ambiance.</li><li>Personal Touch: Since you print it yourself, each lightbox is unique and can be customized with your choice of filament color and finish.</li></ul>Ideal for crafty parents and creative kids, this DIY Monkey LED Lightbox is more than just a light source, it’s a fun project and a personalizable piece of art that will brighten your child’s room and their imagination.&nbsp;Have a look at my Lightbox collection: <a target="_blank" href="https://makerworld.com/en/@KeylineStudio/collections/797633" rel="nofollow noopener">https://makerworld.com/en/@KeylineStudio/collections/797633</a>&nbsp;If you enjoy my models, please consider supporting me and my future designs!<a target="_blank" href="https://www.buymeacoffee.com/keylinestudio" rel="nofollow noopener">https://www.buymeacoffee.com/keylinestudio</a>

Monkey Lightbox

Light Ups

MiMa3D

This is a simple shower rod acoustic phone hanger designed to hang a phone in the shower and listen to music.&nbsp;The hanger is designed to snap onto a 25.4mm (1.00”) shower rod and the phone clip will fit most phones from 8mm (no case), up to 15mm thickness (with a case).&nbsp;The part has been oriented on the bed to improve strength and prevent splitting the snaps/tabs along layer lines. Tree support has been turned.&nbsp;The slicer is set to X1C with a PEI plate and matte pla. Please adjust as required.&nbsp;Thank you!

Shower Rod Acoustic Phone Holder

Fun Makes

maCyo42

It&#39;s done!!! All Parts printed and assembled! I started the Riser V2 early December and changed the last Parts yesterday. There&#39;s a lot of work in this design, so many small and big changes. Today i will start to Release the first completed picture of the Riser V2 and the Profiles of the Mainbodies. As you later can see i&#39;ve seperated some Parts so that you can play around with Step Files for your own Design Fronts.&nbsp;<h2>Should I print the Riser V1 or V2? Here are the differences.</h2><ol><li>There are 2 Versions of the V1. The Standard is for 8mm Lightstrips and the 12mm Edition for 12mm Lightstrip and additionaly you can fix the Lightstrip with Cable ties. V2 combines the Features of both V1 Riser in this Case. I received a lot questions: Will 12mm Lightstrips fit? It can but that is not sure. It not depends only on the width. The stiffness is one big issue for the curves. Try it i cannot guarantee! There are different lightstrips on the market.</li><li>V2 is tuned more for function than design. There are additionaly Connectors for Accessories like Tools.</li><li>Early December i began to work on V2. My intention was the big change in the Anti Glare Feature and the Connectors. But meanwhile there where some critics on the V1. Some Makers reported a bad fitting of their Top Glas. To much loose in the Spoolholder fitting and so on. So the logical consequence was to rework many things on V2.</li><li>The Modders. I had so many Mails and Msg… can you please add Hexagons insted of Holes and so on. Because of this i reworked the Covers and seperated them for the Modders. You can now easily create your own designs on the most seen Parts of the Riser.</li><li>The printability. Puh i don´t know how to begin exactly. Makerworld makes a lot very easy. But a project like this is not easy. It´s big, it can fail as any other Print… it can fail! But you can do a lot that the chance that it will fail is very small. You have to know your printer, your Filament, your Buildplate… The condition is not the same as i have. But it´s quite easy to begin if you have a predefined Profile. But it´s not a Microwave, it´s a 3D-Printer, a popular and wonderfull Printer. It makes a lot easier and it´s the by far best for consumer on the marked… and nevertheless you have to know what you do. Please keep in mind! I reworked a lot to make it even easier. Less Supports (less filament usage is everytime the best optimization!) Tuned Overhangs especially on the back which is on the Print surface while printing Part 3 and 4. and many more changes</li></ol>happy printing<h2>Features Description</h2><h4>Accessories Port New second Accessories Connector Port. The Port is redesigned an optimized. Accessories fits tighter. The Spoolholder on V1 was a bit to loose.</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_d57fe6c9f6869.png"></figure><h4>New seperated Drawer Front Cover and Handle</h4>With the new separated Drawer Front you can create easily your own Designs and Text on it and print it upside down for best looking Surface. (STEP File of the Cover included) The new Handle locks both Parts (Drawer and Cover) together. No Glue needed!&nbsp;Compatible Inserts for the Drawer <a target="_blank" href="https://makerworld.com/de/models/44128#profileId-45567" rel="nofollow noopener">Original Inserts &amp; Dividers</a> by <a target="_blank" href="https://makerworld.com/de/u/1818851574" rel="nofollow noopener">tomtom5893</a><a target="_blank" href="https://makerworld.com/de/models/50855#profileId-52695" rel="nofollow noopener">CHT Nozzle Holder</a> by <a target="_blank" href="https://makerworld.com/de/u/2301853465" rel="nofollow noopener">kylecasey4</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_e7570c3e6befc.png"></figure><h4>New P1S Front Dash Parts with separated Cover for leave Blank or your own Design</h4>In the Standard V2 you have a dummy for the Slot where you can mod different things like a light Switch. The Slot for the MicroSD Card is now protected with a Cover. If you press on the lower Part of the Cover it opens. Yes it´s tricky to get the Card out, but how often you want to get it out… i recommend to use a tweezer or something else. The Covers of Part 5 &amp; 6 is now separated too. You can add your own designs and print it upside down. (STEP Files of the Covers included)<h4><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-16_a2e0b276312d6.png"> Light Strip integration and Anti Glare</h4>The Lightstrip integration is fully redesigned and now combines “V1 Standard” and “V1 12mm Edition” in one sleak Design. You now have a lot of cable tie position to safe your Printer from falling Lightstrip!<ul><li>I strongly recommend COB LED Light Strip with 8mm width. Length 2m and cutable.</li><li>Yes you can also use 10mm or 12mm BUT beware. Most 12mm LED Strip are so stiff that it´s a mess to integrate them.</li></ul>The Anti Glare Feature moved from the Mainbodies to the TPU Gasket Parts because of collisions with the PTFE Tube while printing big Parts. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-17_88977cc660f9.png">Why more Light? Do i need more Light? YES i think so! <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-17_7662231c60b07.png"><h4>The Toolholder Connector</h4>With this Connector you can add whatever you want to the Riser. In the First step i added the Connector for my <a target="_blank" href="https://makerworld.com/en/models/28768#profileId-25133" rel="nofollow noopener">P1S Tools Model (Get it here on Makerworld)</a>. The Toolholder Connector is provided as a Step File as well. With this the Modding Community is able to connect whatever they want. There are 6 Connector Ports 4 of this. 2 on the Left Side and 2 on the Right Side. There are 2 more Connector Ports on the Back in a different design. (STEP File of the Toolholder Connector included)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-18_6005761ec053d.png"></figure>You can also attach a Spoolholder. <a target="_blank" href="https://makerworld.com/en/models/53455#profileId-55205" rel="nofollow noopener">Get my Version with Bearings here</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-01-18_841008088edb2.png"></figure>The “Back Connector” is finally released. Unleash your modding ideas, perhaps for an ESP32 case that can be attached to the back? Use one, two or even all 4 connectors for your modding idea. (STEP File of the Back Connector included)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-02-23_e06df92819799.jpg"></figure><h4>Where to find the &#34;RAW Files&#34; on Makerworld? e.g. Back Connector …</h4>So there are 2 Options. One you can see in the folowing picture as provided by the designer you can find the Parts under “Download STL” else <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_12c13e3925103.png"></figure><h4>Asssembling Guide</h4><ol><li>Push Part 2 on Part 1 <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_0b3ee7ecae28a.png"></li><li>Push carefully Part 3 on Part 4 <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_719957f53c68.png"></li><li>Then push carefully both Parts 3 &amp; 4 together from the Top to the Bottom in Part 1 &amp; 2 <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000133452/design/2024-05-07_1d6c733360ed3.png"></li><li>tba</li></ol>

Proposal

Light Ups

Fun Makes

3D Printer Parts