HribaDesign

I searched and printed a lot of different models, but each one had minor or major flaws, so I decided to tweak my own.<h4>Print instructions</h4>Filament: PLA Print height: 0.2mm Nozzle: 0.4mm Support: Are needed at the endsI printed on Voron2.4R in the settings for voron parts (I know, in the photos I have the first layer a little high.).

Lego train - Straight track rail

Lego

vvojtech1564

Phone holder snap in to dashboard, with intergrated magnets. Its prepared for 20 magnets 8mm diameter and 4mm height. I used 2mm height magnets and one by one added them and tried holding power. Withou mobile case, just with metal shet on phone, 20 magnets holds prety strong(one magnet should hold 1kg). Because I use thick phone case i stack two magnets on top of each other and ended up using 40 magnets.&nbsp; It can be also used just like platform for another holder.

Škoda Octavia 3 phone holder

Sairae

New Crossbow Version! <a target="_blank" href="https://makerworld.com/en/models/425727#profileId-329413" rel="nofollow noopener">https://makerworld.com/en/models/425727#profileId-329413</a>&nbsp;Introducing the Q-tip Shooter V2! Simply load a one-sided Q-tip, pull back the spring, pull the trigger, and launch.&nbsp;Improvements from V1:Faster print timeImproved frame to better fit handThickened Q-tip pocket for better strengthWider bow for better trigger clearanceImproved trigger mechanismLink to V1: <a target="_blank" href="https://makerworld.com/en/models/393963#profileId-295078" rel="nofollow noopener">https://makerworld.com/en/models/393963#profileId-295078</a>&nbsp;&nbsp;Thank you to @eclien for the great revisions made to the original model.&nbsp;&nbsp;

Q-Tip Shooter V2

Guns

vanbluca

Hey guys!When I first saw the wireless bambu mouse, I knew I wanted to make one. Unfortunately, I was really bothered by the ugly sudden flat rear of the mouse. I decided to take matters in my own hands and remodel it with a more aesthetic organic shaped round rear. It could be slightly harder to print vs the original design, however I had no issues first try.I hope you enjoy this version!&nbsp;Edit:Since my original profile may cause issues depending on your bed adhesive, I have added a second profile with improved adhesion.

Wireless Mouse 002 - rounded rear

Single liners for Revell acrylic paints usable for the "Catch-All Trays" system.

Catch-All Trays / Desk organizer - insert for revell colors

Models

I originally downloaded a similar model, but it was too tight and could not be used on my backplate. That's why I made my own and allowed for shrinkage after printing when designing. Fits perfectly on my backplate.I recommend printing the infill at 100%.

AM4 insertion for Backplate

<img src="https://media.printables.com/media/prints/675001/rich_content/2b826a95-30ba-4422-aa0c-e397cfdc2062/video-bez-nazvu_-vytvoreno-pomoci-aplikace-clipchamp-2.gif#%7B%22uuid%22%3A%220e0f20b9-6e88-4c83-b968-269f20fab05f%22%2C%22w%22%3A640%2C%22h%22%3A480%7D">BOM<ol><li>Printed spring holder (print at standard Voron parts settings)</li><li>Silicone roller under the Hotbed.</li><li>M3x6mm FHCS.</li><li>M3x20mm SHCS.</li><li>M3 t-nut.</li><li>M3 threaded insert (optional).</li></ol>Part is fixed to the opposite extrusion side to Z endstop switch, using M3x8mm SHCS & T-nutsIn the macro set your X & Y positions - X Start is to the right of the scrubber.Macro for klipper taken from <a href="https://www.printables.com/model/109349-silicone-brush-nozzle-scrubber-for-voron-24" rel="nofollow">https://www.printables.com/model/109349-silicone-brush-nozzle-scrubber-for-voron-24</a> This configuration is for my V350 2.4R <pre><code>[gcode_macro CLEAN_NOZZLE]variable_start_x: 125variable_start_y: 349variable_start_z: 5variable_wipe_dist: -35variable_wipe_qty: 5variable_wipe_spd: 150gcode: {% if "xyz" not in printer.toolhead.homed_axes %} G28 {% endif %} G90 ; absolute positioning ## Move nozzle to start position G1 X{start_x} Y{start_y} Z{start_z} F{wipe_spd * 60} ## Wipe nozzle {% for wipes in range(1, (wipe_qty + 1)) %} G1 X{start_x + wipe_dist} F{wipe_spd * 60} G1 X{start_x} F{wipe_spd * 60} {% endfor %}</code></pre>

Silicone Nozzle Scrubber - Voron 2.4R

Voron

Bambu Lab

This is a spool holder for Bambu filaments.

Bambu Spool

Ideas

mcmaven

This is a 3D-printed model of a triple-axis tourbillon, which is based on the tourbillon in a Jacob and Co. Twin Turbo Furious watch. A tourbillon is a mechanism employed to counteract the effects of gravity within a watch. This intricate model includes an escape wheel, triple-axis outer frame, and a base with an integrated motor. It functions on the same fundamental principles as a traditional watch tourbillon.&nbsp;With precise assembly and calibration of the escape wheel, spring, and base drive gear, this tourbillon can smoothly rotate in three axes and maintain accurate timekeeping. The provided print settings in the Triple-axis Tourbillon Model for Kit-007.3mf file are already customized to ensure that all screw holes are clear and ready for assembly.&nbsp;Printed plastic ‘screws’ are printed to scale and used as caps to cover the steel screws that actually hold it together.<a target="_blank" href="https://youtu.be/2-7S2i6AUyM" rel="nofollow noopener">Here </a>is a real-time video of the tourbillion in action.&nbsp;Note: There are two different designs defined for the Tourbillon: the 3MF version and the STL version.&nbsp;The 3MF (Triple-axis Tourbillon Model for Kit-007.3mf file) version was designed specifically to work with Bambu printers and the Bambu slicer, and uses the Triple-axis Tourbillon Model Hardware Kit motor to drive it. It is a slightly modified version of the original STL tourbillon version. To build the 3MF version you only need to order the <a target="_blank" href="https://shrsl.com/4d484" rel="nofollow noopener">Triple-axis Tourbillon Model Hardware Kit</a>, which provides all the non-printed parts (screws, bearings, shafts cut to length, motor, etc.) needed to build a complete model. <a target="_blank" href="https://www.youtube.com/watch?v=HRNbihDXNwE" rel="nofollow noopener">Here </a>is a video of assembling the 3MF version with the Bambu 007 hardware kit. Note that some of the sections in the Furious Build Notes PDF file below also apply to assembling the 3MF version, with the primary difference being the construction and components of the Base and the drive mechanism.&nbsp;The STL (Raw Model Files) version is a set od files that was designed to work with any printer or slicer. It also uses a more complex Arduino controlled stepper motor mechanism to drive it. To build the STL version you can order a kit of all the non-printed parts <a target="_blank" href="https://www.makerrx.com/collections/projectkits/products/twin-turbo-furious-tourbillon-kit" rel="nofollow noopener">here</a>, otherwise you will need to order the parts listed in the Furious Build Notes PDF instructions individually. If you order the STL version of the hardware kit or buy the parts yourself, you will need to program the firmware into the Arduino before it will work. The Furious Build Notes PDF file below, describes the assembly process for the STL version. For some of the larger parts, ‘full’ (e.g., Base Outer Ring.STL) and ‘split’ versions (Base Outer Ring a.STL and Base Outer Ring b.STL) of the same part are included. The ‘full’ parts require at least a 220x220 bed for printing. The ‘split’ parts may be printed separately on a diagonal on a smaller bed, then glued together to form the larger part.&nbsp;The following filaments can be used to create a model that looks like the pictured gold, silver, copper and black version:<ul><li><a target="_blank" href="https://shrsl.com/4cim5" rel="nofollow noopener">PLA Silk Gold</a></li><li><a target="_blank" href="https://shrsl.com/4cim4" rel="nofollow noopener">PLA Silk Silver</a></li><li><a target="_blank" href="https://shrsl.com/4cim3" rel="nofollow noopener">PLA Silk Copper</a></li><li><a target="_blank" href="https://shrsl.com/4cim2" rel="nofollow noopener">PLA Basic Black</a></li></ul>Here is a video of the construction of the 007 kit. And some sections in the Furious Build Notes.PDF file may be useful for constructing the 007 kit.<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=bHEU9rnnu88"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/bHEU9rnnu88" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Triple-axis Tourbillon Model Components Kit through the links below, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)&nbsp;The Hardware Kit for the Triple-axis Tourbillon Model for Kit-007.3mf file can be found here: <a target="_blank" href="https://shrsl.com/4d484" rel="nofollow noopener">Triple-axis Tourbillon Model Hardware Kit</a><a target="_blank" href="https://shrsl.com/4cfzj" rel="nofollow noopener">.</a>

TT Furious Tourbillon

Mechanism

Knob for M8 nut

Gadgets

Plant climber inspired by stained glass window

Window plant climber

Plants

Simple spool holder with 3 possible way to use - stand, wallmount and hangingSelfcentring holder, for all common spool.Spool rotate easyly, due to paralel layers.Without aditional screws and bearings, just printed parts.Frame without use of glue, just snap in.&nbsp;Enjoy :)

Spool holder 3in1

Printers

Sun medal

Toys

<ul><li>Stabilizing the axis results in more uniform coffee grinding and a significant reduction in resistance, i.e. easier coffee grinding.</li><li>The printed part needs to be supplemented with one Ball Bearing 626 ZZ (d=6 mm, D=19 mm, B=6 mm).</li></ul>

Hario MINI MILL SLIM PLUS - axis stabilizer

Coffe

A simple display cover consisting of two parts and a piece of filament is used for the hinge axis.Designed in such a way that the visible surfaces are printed towards to the bed, and in the case of using a cover with a logo, so you can print without supports, due to which there will be an interesting connection of the two layers and a slight visibility of the logo.&nbsp;Jednoduchý kryt displeje složený ze dvou dílu a pro osu pantu je použit kousek filamentu.Navrženo tak aby se kryt tiskl pohledovou plochou k podložce a v případě použití krytu s logem tisknout bez podpěr vzhledem k čemuž dojde k zajímáváme spojení dvou vrstev a lehkého zviditelnění loga.

Display cover  - Ender 3

Ender

A simple model for accurate measurement of printed X and Y axes.Designed to eliminate possible printing errors such as elephant foot, protruding corners and other defects that could affect the accuracy of the measurement. In the same way, the cross is based on a 100 mm circle so that the measurement is accurate even in the case of a wrongly placed gauge. I recommend using a digital slider with which it will be possible to measure the part accurately to a few hundredths.Place the seams of the individual layers outside the tops of the cross.&nbsp;Jednoduchý model pro přesné měření tištěných os X a Y.Navrženo tak, aby byly eliminovány případné tiskové chyby jako je sloní noha, vystouplé rohy a další nedostatky, které by mohli mít vliv na přesnost měření. Stejně tak kříž vychází ze 100 mm kružnice aby bylo měření přesné i v případě špatně umístěného měřidla. Doporučuji použít digitální posuvku se kterou bude možné změřit díl na několik setin přesně. Švy jednotlivých vrstev umístěte mimo vrcholy kříže.

XY calibration cross

Calibration

Hidden hook with hidden mounting to the wall.