Grossi1981

kevin1068

Set of spice bag holders made to fit inside kitchen cabinets. I use them to unclutter those bags you can see in the photos. I made two sizes that fit all the bags I usually buy. Let me know if you need other sizes. Filament ran out when printing the smaller one, still turned out great.&nbsp;Sizes (WxDxH) 15 x 6 x 6cm 7,5 x 6 x 6cm &nbsp;The wall thickness is 1,3mm and depending on the filament I recommend enabling a brim.

Spice/sauce bag holder

Küchen tools

Thyristor

As eSUN sends plastic or cardboard spools randomly, I aimed to design an adapter that performs better than the typical ring adapters. Thus, I created this one as part of the <a target="_blank" href="https://makerworld.com/en/models/search?keyword=cbas" rel="nofollow noopener">CBAS</a> series.&nbsp;&nbsp;The spool needs around 158 grams of filament with 15% infill, making it not lightweight but rather sturdy and smooth-running. So far it has always fit perfectly into the spools core. The Silica Compartment Lids add approximately another ~16 grams.&nbsp;<h3>Updates</h3>24/06/06 75mm Spool addedFinally, the 75mm spool is here! The files for it are marked with *75*. Compatibility with LSM and SCL remains intact. The weight is reduced to approximately ~146 grams. However, i have not yet received any of the new eSUN spools. As long as they have not become significantly thinner, they should fit. I would greatly appreciate any feedback!&nbsp;24/02/09 More LSM variantsAdded LSM labeling for more eSUN materials.&nbsp;23/01/02 Silica compartment lid updateAdded the Silica Compartment Lid (SCL) - with this cover, the spools core can be sealed, allowing it to be filled with silica bags or loose beads. Loose beads should be bigger than 1.5mm, as smaller beads may pass through the air slots. For easier tightening and loosening of the SCL, you can find the TwistAssist listed under accessories below. The SCL is only compatible with prints printed from files tagged with the SCL label.Changed the default print profile to the SCL version. The SCL variant remains compatible with older versions. It gains approximately ~4 grams in weight.&nbsp;23/12/27 Label space module updateProfiles for the label space modules (LSM) have been added, labeled with the most common filaments as well as an unlabeled variant - unlabeled also available as .step file.&nbsp;23/12/20 New defaultSet the label space module spool as the default print profile. The spool now has an additional 10 grams of weight but remains fully compatible with the old version.&nbsp;23/12/17 - Added Label Space ModuleA new spool version has been added. With this spool, a designated area known as the Label Space Module (LSM) can be inserted into the available spaces. This module can be covered with stickers or printed with text as desired.This spool needs around 154 grams of filament with 15% infill and both parts are compatible with the non label space module parts.&nbsp;<h3>Assembly</h3>To assemble, first remove a cardboard side of the eSUN spool and replace it with a printed half, some of the glue residue may need to be removed. Hold the spool and turn it over, then remove the other side, now screw the halves together until they are tight.The label space module can be inserted into both parts of the spool, preferably when the spool is not yet loaded, and it may require some effort depending on your printer.The SCL can be easily screwed into the thread of one of the spool cores.&nbsp;It&#39;s best to wrap the filament with painter&#39;s tape beforehand to prevent it from unwinding on its own.&nbsp;<h3>Accessories</h3>This spool is part of the CBAS series and can make use of these accessories.&nbsp;TwistAssist for spools of the CBAS series equipped with the Silica Compartment Lid (SCL):<a target="_blank" href="https://makerworld.com/en/models/119878#profileId-128974" rel="nofollow noopener">TwistAssist for SCL</a>&nbsp;For those who prefer not to use the holes in the spool to secure the filament, here is the appropriate filament clip:<a target="_blank" href="https://makerworld.com/en/models/63688#profileId-66694" rel="nofollow noopener">FilaClip for CBAS</a>

Küchen tools

Printer Tools