GreyWolfe111

cover

Printed shoe horn with supports.png

shoe horn.png

Slide in Shoe horn

Shower 1" Pole Support Clip

Enclosure Access Slide Panel

Laundry Sink Drain Protector

3"  Tape Core

Cord Passthru

6" to 4" Duct Reducer 

Deep Funnel

Earwig Bait Station

PTFE coupler Straightener Support

Smoker Jerky Rack Stand 

Scotch C22 Tape Dispenser Core

Cabela's Slicer Bottom Guard

Ant Bait Station

Heater Dial 

Tape Dispenser Core 25.9 mm 

Kitchen Roll Tray Holder

Spool Edger Tape Guide

Donation Jar Display Sign Topper

Drawer Bottom Edge Runner

Printed well, I used this type of design on the AMS 2 too, I also changed up the infill to gyroid on it and this print. Tried out the newer multi line setting on this set. I went with three but two would probably do well also. However you’ll need to make sure do do enough percentage. I did around 40-45 and any shattered desiccant likes to poke out with what I did. The first set before the multiline infill the screen walls were weaker, but didn’t have an issue with cracked desiccant. Not the designers fault, just what I had changed it to. 

Joey Lopez Design (AeonJoey)

SPILLPROOF AMS Desiccant Box -RECTANGLE Hygrometer

Lower Hygrometer Position - Full Set

I did have to alter the scale just a bit to make it a tighter for my Skoam branded containers. They fit but repeated opening and closing and they wouldn't stay put. Once I adjusted it, they fit nice and tight. I like how you added the angled edge indent for using a screwdriver to help pry it out if it needed any help.  Previously I used a bit different design for my dryboxes, But they were a bit weak in the corners. This is much sturdier.
Thank You, Awesome Job

DrHellbenders

Tasogen Hygrometer Insert - Praki 4L Container Lid

Tasogen Hygrometer Insert – Praki 4L Container Lid

0.2mm layer, 3 walls, 25% infill

First largish ASA Print. First half with skirt and carbon filter running.  Second print, lid and accessories with internal carbon filter off.
Both had all three threaded parts a bit stringy from I assume were the overhangs. After removing the stringiness it assembled fine without issues. Not sure if it was my filament settings or the design.

However, It works!  I'm happy and that is all that counts. Now I have a better choice of how I can refresh my silica desiccant while keeping it well constrained and not a home disaster if it tips like an open tray can be.

PattonDesign

Spool Sized Desiccant/Silica Dryer/Holder

Version 3 - AMS 2 Pro/HT Compatible Dryer

Changed up the Infill to 35% Gyroid. Made it look like simulated screen fabric. My AMS2 Desiccant Boxes used this so I changed it to match. Printed great except for I had a build plate adhesion issue from not freshly cleaning the plate and had to print one part over. 

Only thing I didn't really think about, is my USB Drive protector and the Screen doesn't fit side by side. Both the left spacer and width interfere. For now the Screen won out. I'll just have to adjust and reprint the drive protector.

The screen serves two functions which is more important. 

1. Keeping anything smallish that might be set on top of the glass from rolling into the vent during it's rock, rattle and roll on the dampener feet.

2. The fabric-ish type screen should help with some of the dust entering due to the exhaust fan and air flow.
     I also think it looks just a bit more stylish then the grid pattern.



sven.designs

H2D/H2S/H2C - Vent protector and filter

Vent Protector & Filter 

Earn this badge when visit MakerWorld more than 20 days in last 30days UTC time

MakerWorld Guardian

Earn this badge when print successful more than 100 different models and 500 hours

Pioneer Maker

4L Cereal Box frame insert