GrayFabrication

DylanRyanDesign

I wanted to put the full build plate size of my A1 to the test, so I designed this modern looking fruit bowl.It takes about 3 hours to print depending on what version you choose.&nbsp;I designed 2 versions:<ul><li>With 4 rubber feet (10mm x 2mm) can be found in most hardware stores or on amazon</li><li>Without rubber feet</li></ul>If you have some TPU, you could also make the feet yourself.&nbsp;I have uploaded 2 print profiles:<ul><li>0.4mm nozzle : has 2 plates, 1 with rubber feet holes, 1 without </li><li>0.6mm nozzle : has 2 plates, 1 with rubber feet holes, 1 without </li></ul>&nbsp;If you have any feedback or problems, please let me know ⚒️&nbsp;also if you decide to make this in some other colours I would love to see some pictures 😁🍌&nbsp;&nbsp;

Modern Pleated Fruit Bowl - Large - A1/P1/X1 

Home Decor

Adam L

Do you want to print plastic as clear as you can on your printer? &nbsp;This tuned set of profiles for BambuSlicer/OrcaSlicer should help you print as clear as i've been able to tune on my X1C with Overture clear PETG. &nbsp;I've tried several different parameters and come up with the best settings I can. If you are curious, this is option #8 in the test samples I have in the photos.&nbsp;I took many of my lessons in glass tuning here from prior art and those examples are linked as remixes here.This process and filament profile is tuned for Overture Clear PETG, reported to be one of the best for this purpose.Tips<ul><li> Printing “glass” means patience. Hot and slow is key here for good results. </li><li>You can try to increase the print speed and layer height from the starting point here.. but your results may get worse (mine did). </li><li>Close your chamber door and top as well. My ambient chamber temps were 30-39 deg. C or so during most of the print.</li><li>Since this is very slow, the nozzle type likely doesn't matter here and this should work decently well for X1/P1S/X1E. It may also work fine on an unenclosed P1P, but ideally you want the environment warm to slow down any annealing.</li></ul>

Print Glass With Your Bambu X1/X1E/P1S/P1P:   Orca / Bambu Slicer + Overture Clear PETG formula

Print Profile

Every Day Counts

UPDATE 27 Oct 2023: A new, softer version of the bin (named Wavy) is available at <a target="_blank" href="https://makerworld.com/en/models/50582#profileId-52329" rel="nofollow noopener">https://makerworld.com/en/models/50582#profileId-52329</a>&nbsp;Also, I have created a version of this with the space for a <a target="_blank" href="https://makerworld.com/en/models/50674#profileId-52400" rel="nofollow noopener">badge or label</a>.&nbsp;Easy to print in any material, but PLA will be sufficient.Photos show it in Bambu Labs PLA Metal (Blue) filament.Print with a brim to ensure that the base remains flat.Size is 198W x 198D x 186H (mm).&nbsp;I now have a swing lid available for this model. See <a target="_blank" href="https://makerworld.com/en/models/45467#profileId-47202" rel="nofollow noopener">Swing Lid</a><img src="https://makerworld.bblmw.com/makerworld/draft/146326/2023-10-20_4f40259934d3f.jpeg">&nbsp;Also, a flat lid is available at <a target="_blank" href="https://makerworld.com/en/models/46903#profileId-48688" rel="nofollow noopener">Flat Lid</a>.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/146326/2023-10-22_5032c1fd1ecac.jpg"></figure> Please also see my other bin models on <a target="_blank" href="https://makerworld.com/en/u/369067369" rel="nofollow noopener">my homepage</a>.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/146326/2023-10-28_c78a63d83f5dc.png"></figure>

Decorative office trash can

Office

SimonMakerForge

Description&nbsp;This is caddy-tray tools foldable and with some accessories. This caddy will be useful during summer days on the beach because it can be easily adapted to many umbrella shaft. The caddy will fit the main clamp and it will be free to rotate.The caddy-tray is very robust and can hold lot of weight.It is available also a hook and a plate which can be easily connected to the main caddy.PETG or hi-temperature material is recommended for this tools.&nbsp;How is composed<ul><li>The Clamp</li></ul><figure class="image image_resized" style="width: 41%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_a0a3a8b3b5923.jpg"><figcaption>clamp size adjustable for shaft diameter fro 23mm up to 38mm</figcaption></figure><ul><li>The foldable caddy-tray</li></ul><figure class="image image_resized" style="width: 38.64%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_6191ecacdefb1.jpg"><figcaption>when it is closed (folded) then the umbrella canopy can be closed wthout removing the tools.</figcaption></figure><figure class="image image_resized" style="width: 37.52%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_0285859fd2193.jpg"><figcaption>when it is open, can be used as caddy and tray</figcaption></figure><ul><li>The Delta Plate</li></ul><figure class="image image_resized" style="width: 55.52%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_c5065accbcca3.png"><figcaption>This container can increase a lot the space of the caddy and it will be useful especially for bottles and cans</figcaption></figure><ul><li>The Hook</li></ul><figure class="image image_resized" style="width: 53.62%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_abe967aaf4acc.png"><figcaption>Can be connected to the delta-plate or to the caddy easily. It will be useful for holding bag.</figcaption></figure>&nbsp;This is the final result:<figure class="image image_resized" style="width: 61.79%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_ad6b91ba9e0bc.png"></figure><figure class="image image_resized" style="width: 60%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484562/design/2024-05-05_4b6edc9f96f2c.png"></figure>See also my others designs:<ul><li>Roller Molder for Sand (modular roller molds): <a target="_blank" href="https://makerworld.com/en/models/484295#profileId-396633" rel="nofollow noopener">https://makerworld.com/en/models/484295#profileId-396633</a></li><li>Beach Towel Holder-Peg: <a target="_blank" href="https://makerworld.com/en/models/484289#profileId-396627" rel="nofollow noopener">https://makerworld.com/en/models/484289#profileId-396627</a></li><li>Zen Sand Tools: <a target="_blank" href="https://makerworld.com/en/models/483766#profileId-396033" rel="nofollow noopener">https://makerworld.com/en/models/483766#profileId-396033</a> </li></ul>If you like them… please download them and leave me a like!<a target="_blank" href="https://buymeacoffee.com/simonmakerforge" rel="nofollow noopener">If you want to buy me a coffee..</a>

Swiwel and foldable Caddy-Tray for beach-camping

Summer

Robin S

<h4>On platforms like makerworld, printables and co. there are often phonecases to see but for most people it is the wrong phone!</h4>This is a phone case generator,where you can create your custom and individual phone case.&nbsp;You just have to follow the steps and measure out your phone. Then you have to put these measurements into the generator and you&#39;ll get a complete model including all offsets and risks!&nbsp;If you want to have the same look like in the cover picure remove upper and lower layers in your slicer settings and choose your favourite infill!&nbsp;&nbsp;<h3>Introduction</h3>You can create your own phonecase fitting to your phone.First you have to open the customizer web-tool from this model. Then you have to measure out your phone and put the in the web-tool described values in and then click on generate. After that you can download the 3d model.&nbsp;<h4>Special variables</h4>-&#34;cam hole distance&#34;: With these two variables you set the distance to the cam hole from the upper left corner. x means the distance horizantally and y vertically. (Same at “cam hole size”)&nbsp;&nbsp;-&#34;distance to upper button&#34;: You have to set this value to the distance from the upper edge of the phone to the first button on the right side of the phone. Buttons on the left side are coming soon! Offsets are included so don&#39;t change the values just put the exact measurements in.&nbsp;-&#34;text position&#34;: Here you can say where your text on the backplate of the phonecase starts. With xt and yt you can move the text on x aand y axis.&nbsp;&nbsp;<h4>Offset variables description</h4>&nbsp;<img class="image_resized" style="width: 51.49%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_97b47e74d476.jpg">Offset “o” is the main offset, which makes a little gap between phone and case.I recommend to set this offset to 0.2-0.6 mm.&nbsp;&nbsp;<img class="image_resized" style="width: 50.09%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_03af8a7bd6a57.jpg">The variable “n” sets how strong or how hard the case holds the phone in place.I mostly used 1-1.2 mm.&nbsp;&nbsp;<img class="image_resized" style="width: 49.98%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_9fe8713d1773b.jpg">With the variable “s” you set the height of the grips that holds the phonein the case. Here you can leave it at 1 mm.&nbsp;&nbsp;-Now I added a new feature where you can add a text on the backplate of the phonecase. Just put for example your name on it and move it to the right position with “text position” variables. You can also adjust the size of the text.&nbsp;-added feature: Buttons can be created on both sides. If the length of the buttons is set to 0 they will be removed.-added left speaker hole&nbsp;print tipp:-enable the feature in the slicer, print infill first. So your printer will print the overhangs better.&nbsp;&nbsp;&nbsp;If you successfully made your own phonecase, great job, please send me an email with your values if it’s not in the following excel sheet yet. Then send me the measurements, the phone name and a picture that you printed it to this email adress:<a href="mailto:3dprint_robin@web.de" rel="nofollow">3dprint_robin@web.de</a>So we can add those values to a big library where everyone has access to the sizes of their individuell phone.Otherwise you can upload a remix to this model to achieve the same.The link to the excel sheet:https://docs.google.com/file/d/1-4dP4UFD8Y4-3RfeF4kMAfZTcvU_xaJY/edit?usp=docslist_api&amp;filetype=msexcel&nbsp;

Custom phone case 

phone

Heart Labs

<h2>Beschreibung</h2><h3>Junction Box SLIM mini</h3>Modeled after our Junction Box SLIM line, the mini version packs all the features the big ones come with and is here for you to try out forFREE!More information about the whole set and its features you will find under <a target="_blank" href="https://www.printables.com/de/model/752883-junction-box-slim-full-set" rel="nofollow noopener">Junction Box SLIM Full Set</a> <a target="_blank" href="https://www.printables.com/de/model/752883-junction-box-slim-full-set" rel="nofollow noopener"><img class="image_resized" style="width: 23.1%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000475476/design/2024-05-26_471714fab2dd48.gif"></a><h3>Technical Drawin</h3><h3><img class="image_resized" style="width: 44.24%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000475476/design/2024-05-26_026d4b0340562.png"></h3><h3>Compatibility</h3><ul><li>2x WAGO 221 412</li></ul>&nbsp;<h3>⚠ DISCLAIMER ⚠</h3>Depending on the country you live in, this junction box might not full fill the regulatory requirements to be permitted for usage above 120V. We are currently actively working on certifying this set in the EU, which is easier said than done. So cross your fingers!

Junction Box Slim Mini

Outside

Maanprint

Update! Updated models, basic planters. 11 different sizes, with and without drain holes, and coasters. The planters now all have the same proportions and the wall thickness is the same. Fixed the overhang, it now looks better. The new files are here <a target="_blank" href="https://makerworld.com/en/models/480687#profileId-392308" rel="nofollow noopener">https://makerworld.com/en/models/480687#profileId-392308</a> --------------------------------------------------------------------------------- Basic planters in 4 sizes (old) 1. Height 4cm, bottom 3cm, top 4cm. Time 34 min. 2. Height 6cm, bottom 4cm, top 6cm. Time 51 min. 3. Height 10cm, bottom 7cm, top 10cm. Time 90 min. 4. Height 18cm, bottom 12cm, top 18cm. Time 3h. 50 min. You can add a drain hole in the slicer, if you need one.  UPDATE* Add a print profile with draining holes.  UPDATE* I made coasters for the planter, these can be found here. <a target="_blank" href="https://makerworld.com/en/models/472713#profileId-382600" rel="nofollow noopener">https://makerworld.com/en/models/472713#profileId-382600</a> Check out my matching watering can.  <a target="_blank" href="https://makerworld.com/en/models/467621#profileId-376740" rel="nofollow noopener"><img class="image_resized" style="width: 30.95%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000466039/design/2024-05-18_b37ca09c9d0f.jpg"></a>

Basic planter 4 sizes

Harpers 1st Bday

bonfiggy

Perfect fitting antivibration feet printed in TPU with 15-20% infill for best results. No supports needed! Seems to help a good bit as well with the shaking/noise and a lot less printer wobble as well :)

Bambu Lab P1P/P1S/X1/X1C Anti Vibration Feet

Tools

taylormadearmy

UPDATE:- Version 2 which is easier to print is here: <a target="_blank" href="https://makerworld.com/en/models/463356#profileId-371871" rel="nofollow noopener">https://makerworld.com/en/models/463356#profileId-371871</a>&nbsp;This is really fun when printed in TPU - it&#39;s so very satisfying to play with compared to the solid versions of this model. And importantly is silent when in TPU - which is great for kids who need to use something like this in class to relax (my daughter loves it).  It also prints well in PLA if that&#39;s more your thing - but you are missing out!I recommend you use my TPU profile and some glue stick - print it slow and steady and you&#39;ll have a gorgeous toy on your hands!&nbsp;This is my first attempt at a print-in-place articulated design, but works well!I&#39;ve printed it successfully at 100% down to 65% in both PLA and TPU. You can even just scale down in the x and y or z independently if you want to try something different - there is a lot of slack in the design.  Try my easter themed version <a target="_blank" href="https://makerworld.com/en/models/216491#profileId-235537" rel="nofollow noopener">here!</a>&nbsp;The design has some supports built in for the curved edges.Once again - Good plate adhesion is required - on my P1S I needed to use some gluestick to make it reliable.&nbsp;<h2>Try some of my other popular and easy-to-print fidget toys</h2><ul><li><a target="_blank" href="https://makerworld.com/en/models/500794#profileId-415835" rel="nofollow noopener">New! Fidget Ring Spinner Planetary Gear</a> - a really easy yet satisfying print and fidget toy!</li></ul><img class="image_resized" style="width: 348.672px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173882/design/2024-06-19_4f91ce3cc8295.jpg"><ul><li><a target="_blank" href="https://makerworld.com/en/models/487776#profileId-400600" rel="nofollow noopener">New! Flippy Flappy Pyramids</a></li></ul><img class="image_resized" style="width: 357.109px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173882/design/2024-06-07_aca38902ac3f.jpg"><ul><li> <a target="_blank" href="https://makerworld.com/en/models/484833#profileId-397248" rel="nofollow noopener">Infinite Flippy Flapper Fidget Toy Version 2</a></li></ul><img class="image_resized" style="width: 358.328px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173882/design/2024-06-13_30730804bb22c.gif"><ul><li>If you want to try another interesting fidget toy with live hinges - you will like my new <a target="_blank" href="https://makerworld.com/en/models/441560#profileId-347321" rel="nofollow noopener">Squishy TPU infinite cube</a> </li></ul><img class="image_resized" style="width: 369.047px" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173882/design/2024-06-07_559fe1e056db1.gif"><ul><li><a target="_blank" href="https://makerworld.com/en/models/445631#profileId-352092" rel="nofollow noopener">Extra long Flippy flappy fidget Toy</a></li></ul><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000173882/design/2024-06-07_47d775bd409ce.gif">

Squishy silent Morf Worm fidget stretch toy

Fidget

MrGnarly

Credit goes to designers. <a target="_blank" href="https://www.thingiverse.com/thing:2549335#How%20I%20Designed%20This" rel="nofollow noopener">Frostmourne - Warcraft by Precision3DPrinting - Thingiverse</a>

Frostmourne From Warcraft v2

Cool Shit

Officina23

I present to you my interpretation of the recirculating air filter. The principle is always the same, a Hepa filter to block the smallest particles (VOCs) and activated carbon to absorb smells/fumes generated by certain materials such as ABS, ASA, PC, PA, etc. (usually those that require to be printed with Enclosure).I used the classic &#34;Bento Box&#34; for a few months, a filter that was the source of my inspiration. This is a complete redesign, not a simply remix: I designed it completely from scratch. It&#39;s wider, it&#39;s taller, it&#39;s more efficient and in my opinion it&#39;s also better looking.&nbsp;Filaments used to print my scrubber: Bambu Lab PETG-CF Black (31100) Bambu Lab PETG-CF Malachite Green (31500) Bambu Lab PETG-CF Brick Red (31200)For templates and covers I used common PLA.&nbsp;<figure class="table" style="width:98.41%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><thead><tr><th>What do you need</th><th> </th></tr></thead><tbody><tr><td>In addition to your printer, you need something else to complete the model. These are cheap components, on sale almost everywhere: 2x 4028 fans (or 4020, to be mounted with the spacer found in the optional plate of my print profile); 4x threaded inserts that must be locked into the fan duct; 4x screws M3 x6, x8 or x10 to join the fan case with the fan duct;  If you don&#39;t want (or can&#39;t) use threaded inserts, you can join these two parts by gluing them together. 24x magnets 5x3 mm to join all the other parts; 1x Hepa filter 80x40x15mm to place in the upper container; at least 50g of activated carbon, acid-free type recommended, to place in the middle container. To avoid any surprises, I purchased the one sold as a refill for the Bento Box.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-02-25_b96543d7f3d1b.jpg"></figure></td></tr></tbody></table></figure><figure class="table" style="width:98.41%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><thead><tr><th>Assembly guide and notes</th><th style="width:320px;"> </th></tr></thead><tbody><tr><td>Fan Duct&nbsp;1. Glue the logo on the side following the slots; you can use the template found in the &#34;optionals&#34; plate, but it is not essential.2. Insert the threaded inserts into the holes in the fan duct; the temperature of the inserts must be sufficient to make them penetrate the material, but not too high to avoid deformations; 3. Place the fan enclosure over the fan duct and join them with the four M3 screws;If you don&#39;t want to use threaded inserts, you can glue the fan duct to the fan case using the 4 pins that are in plate 5 to align the two parts perfectly. This will not affect the ability to mount and dismount the fans.&nbsp;Notes: from February 28th in the print profile you will find the fan duct with three air deflectors. If you want to print the version without baffles you see in the photo on the right, you will have to download it separately.</td><td style="width:320px;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-02-25_0eb1b3a8c2a22.jpg"></figure></td></tr><tr><td>Fan Case&nbsp;1. Insert the two 4028 fans and pass the cables and connectors through the appropriate hole until they reach the bottom of the fan duct. If you use two 4020 fans, insert above the fans the spacer that is in the optional plate of the print profile;2. Insert the green fan Conveyor, which will keep fans locked in place. If the Conveyor goes in too easily and is easy to pull out, lock it with a couple of drops of CA glue;4. Insert four 5x3 magnets into the appropriate holes on the top of the Fan Case, making sure the polarity is in the same direction for all magnets.5. When you have finished all the wiring you need, place this block inside the printer in the bottom right corner; secure it with double-sided tape or screw it into the hole already present inside the printer.</td><td style="width:320px;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-02-25_86de061383266.jpg"></figure></td></tr><tr><td>Activated Carbon Case&nbsp;You should use “pellet” activated carbon so as not to disperse its dust, and acid-free type to avoid corrosion of the metal parts over time. If you use “flakes” activated carbon, after placing it in the baskets let the powder fall before placing them in their container.&nbsp;1. Insert four 5x3 magnets into the appropriate holes on the top of the Carbon Case and other four magnets on the opposite side. Before inserting the bottom magnets, pay attention to the polarity; when you overlap the stages the magnets should attract each other, not repel each other.2. Put some pellets in the red basket (the one with the two handles); Fill it halfway, so as not to obstruct the passage of air. Place the green basket on top of the red one and put the activated carbon. Repeat until you have stacked all the baskets.3. Finally insert the stacket baskets into the Carbon Case, always holding it vertically.&nbsp;Notes: the 3D preview of plates 3 and 4 show the lower grids of the baskets as a solid. Grid will be generated directly from the slicer, where I have set zero upper and lower layers and an infill between 30 and 40% depending on the position of the basket.</td><td style="width:320px;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-30_0b35052a01f44.jpg"></figure>&nbsp;</td></tr><tr><td>Hepa Filter Case and air intake&nbsp;1. Insert four 5x3 magnets into the appropriate holes on the top of the Hepa Case and other four magnets on the opposite side. Last four magnets must be inserted on the bottom of the Air Intake black frame. Before inserting any bottom magnets, pay attention to the polarity; when you overlap the stages the magnets should attract each other, not repel each other.2. Insert the green filter holder into the black container, then place the filter. The expected measurements of the filter are the most common: 80x40x15 millimetres. If you need to use a filter of different sizes write me a message and I will prepare the adapters.3. Insert the green air intake into its black container, and place it on top of the filter container.&nbsp;Note (1): why did I make the upper part in two small containers (Hepa case and air intake) instead of joining the black container in one piece? Because to replace the filter you just need to detach only the air intake, and also to be able to make any developments/variants of this piece without having to reprint too many objects.Note (2): in the print profile you will find the raised version of air intake: this for capturing the air as close as possible to the print plate. Mount this part with the lower half facing the back of the scrubber, so you can slide it under the printer black frame. If you prefer a lower version, please download the two .stp files &#34;Air Intake (short)&#34; and “Air Intake Conveyor (short)” from raw model files.</td><td style="width:320px;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-31_c60b49387f23c.jpg"></figure></td></tr><tr><td>Optionals&nbsp;Carbon and Hepa words are optionals.If you want to use them, print the &#34;optional&#34; plate in the print profile. You will have all the letters you need and the templates to glue them in perfect position on the frames.To glue them, first position the template and then introduce the letters where you will have already applied a very small amount of CA glue. Wait for the glue to dry and then gently remove the template. Covers are another optionals. There is a print profile with three types of covers to prevent filament debris from entering to the filter case when the fans are turned off: - a cover with magnetic fastening (requires four 5x3 magnets) to close the Carbon Case or the Fan Case when others upper cases are not in place;- a cover with interlocking fastening to close the air inlet on the first low version of hepa case;- a cover with interlocking fastening to close the air inlet on the actual raised version of hepa case; this cover also partially covers the black printer frame, but does not interfere with the movements of the print head.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-07_d067fb69e2899.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-31_5912dc7408aa7.jpg"></figure></td></tr><tr><td>Wiring  Feel free to wire the scrubber as you prefer, but if it helps you, I designed the fan duct to hide the cables as much as possible: under the chute there is a space to hide the fan connectors, and on the back wall there there are two diagonal holes for the power cable to come out. I left the power cable long enough to be able to disconnect it without problems, and it remains hidden between the scrubber and the right wall of the printer. I passed it through one of the holes in the frame, and since I use a 12V external power supply for the fans, the cable comes out from the bottom of the printer passing through one of the holes already present in correspondence with the original cable glands. To do this I had to remove both the side and rear panels, but it was a good opportunity to do some cleaning ;-)&nbsp;Since the two 4028 fans I used are very powerful but also noisy, I used an inexpensive dimmer to adjust the speed of the fans. I normally run them at 25% with PETG, 50% with PAHT and 75% with ASA and ABS.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-05_3c901b36f74ca.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-03-05_0f404936b9eb5.jpg"></figure><figure class="image image_resized" style="width:50.54%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000203175/design/2024-04-17_0af2125c89b72.png"></figure></td></tr></tbody></table></figure>&nbsp;

Air scrubber / purifying filter

Filter

Layer by Layer

It took around 1hr to print on my P1S does not require supports. I printed at 20% infill. It also floats like an alligator so it would make a great bathtub toy! If you like it, Make sure to hit that like button and out nice photos of your makes!

Alex the gator flexi desk toy stress relief

Katie’s Class

Clayton Merkle

A tool for creating sealed, crust-less penut butter and jelly (or other) sandwiches similar to Uncrustables. Simply place a dollop of your desired filling in the center of a piece of bread, place a second piece of bread on top, place the sealer on top of the top piece of bread and press down firmly, and then slide the cutter over the sealer and press down and twist a little. &nbsp;This design was inspired by other similar models, however I found that they did not work well as the cutters were not sharp enough, so I decided to make my own.

Uncrustables Peanut Butter and Jelly Sandwich Cutter

Kitchen

R C 3D

PRINT PROFILES: The following are the only print profiles tested and approved by me. They are listed by the name I've given them in the print profile description. I can not guarantee the quality of any print profile posted by anyone other than myself.<ol><li>BLV Remix FR (v2)</li><li>BLV Remix FL (v2)</li><li>BLV Remix RR (v2)</li><li>BLV Remix RL (v2)</li><li>BLV Remix DRAWER</li><li>BLV Remix ACCDRAWER</li><li>BLV Remix Shorty (No Drawers)</li><li>Riser v3</li><li>Gasket</li></ol>&nbsp;SUMMARY: This is a remix of the BLV Riser. The intent was to simplify the assembly, print easier, and with less pieces/material. The original uses close to 2.7kg and this one uses 1.5kg for the primary body, the drawers are between 100-220g, the gasket is 60g of TPU. I will leave the original files in the raw files repository, but will be removing the print profiles that are outdated. The riser maintains the LED light strip sockets, the drawers, the build plate slot, and the high and low shelves for the top glass. I've added a gasket that will work with both the newer and older models. For the older models, you may need to glue it in place because the design intent was to drop it into a small recess, which is only present on v3. &nbsp;&nbsp;Ideally, use PETG or any other filament with a higher temperature resistance. PLA will deform over time. With that said, I use a PLA version on one of my printers which only prints PLA and I have no issues with it so far. I would recommend TPU for the gasket.&nbsp;&nbsp;This riser has a few versions:<ol><li>The first version is the original remix with drawers.</li><li>The second version is the remix without the drawers. Additionally, this version has a sloped inner edge to mount an LED strip at an angle for optimal lighting. I bored out the rear hole slightly so you can terminate the led strip in the rear and run the cable out of the back.</li><li>The third version (v3) is the original remix, but with a slot for a gasket and sloped edges inside for mounting an LED strip at a slight angle.</li></ol>&nbsp;Printing/Assembly:If you decide not to use the print profiles, these are the settings I used.&nbsp;<ul><li>Global Settings:<ul><li>0.2mm Layer Height</li><li>3 Wall Loops</li><li>Enable Supports: Normal (Auto)<ul><li>Snug</li><li>On Build Plate Only</li></ul></li></ul></li></ul>&nbsp;Assembly:The assembly can be done in a matter of seconds. The joints are made with dovetails and a fairly tight fit for a nice press-fit application.&nbsp;<ol><li>Assemble the front two pieces</li><li>Assemble the rear two pieces</li><li>Assemble the front and rear halves together</li></ol>&nbsp;That's all there is to it. Follow my facebook page, RC3D, for giveaways and entry details as well as my latest models.&nbsp;CHANGELOG:&nbsp;UPDATE 12/22/2023:Added v3. This version includes the same sloped edges that the shorty does, as well as a slot for the gasket. I've also included the gasket since the original BLV has nubs that won't work right with this one. The gasket is designed to simply drop into a recess, so it will work on older versions, but you may have to glue it in place.&nbsp;UPDATE 11/25/2023:Added a second version without the drawers. Removed several print profiles and re-organized the files.&nbsp;UPDATE 10/31/2023:I revised the drawer insert and the drawer itself. The new version is very similar, but required just a few changes in order to work probably with the new drawer insert. The insert now fits into the side of the drawer as well, so you'd insert the piece and slide it into the side. This helps avoid issues with alignment and helps position the insert correctly. I also remove the accessories tab from the insert as it made no sense in this application. Instead, the other half of the drawer will just be empty.&nbsp;UPDATE 10/27/2023:Update the insert to fit better, revised the drawer for better printing and fit. The insert and the drawer need to be super glued and held in place for a minute or so (I used clamps) so the bottom sticks to the existing drawer and doesn't snag the edges when the drawer is inserted.&nbsp;UPDATE 10/20/2023:Uploaded an insert to convert the drawers to one similar to the original model. Simply drops in and was intended to just glue in place. I haven't yet tested it, but it's going on the printer tonight so if you'd rather wait I will update this description when mines complete.&nbsp;INITIAL RELEASE 10/15/2023:&nbsp;The design is based on the popular AMS riser by Benlevi. My goal was to reduce the number of pieces, complexity of assembly, and ease of printing. The result is this 4-piece body with dovetail interlocks and 2 drawers. I will be improving on this and am currently printing the latest iteration, but its here for you to try as well. If you find any issues, let me know and I'll make it right.The riser has slots on top for the AMS feet, high and low shelves for the glass Lid, build plate holder, and two drawers.&nbsp;ASSEMBLY:&nbsp;Assemble the front two pieces, then the rear two pieces, then assemble the resulting front and rear halves together. The sequence is important. I glued the pieces for peace of mind, but I'm not sure it's totally necessary. The pieces should only slide together one way.&nbsp;PRINT SETTINGS:&nbsp;• 3 walls• 15% gyroid infill• Supports, snug auto, on build plate only (this is for a small lip at the bottom that will not be visible when installed.)

AMS Riser Remix

Organizer

Jacky Huang

I had changed all my box to v3, please use my AMS dry box center v3.3mf for print.If the hygrometer(some is so big) is a little small, please use same paper to fit it(I used it in photos).For drying Bambu AMS box, you can directly add color-changing silica gel desiccant, non-toxic orange desiccant is recommended.Many designs were referred to,more than 20, but none of them could meet the requirements, so the model is a new drawing designs.Compared with other dry boxes that can be searched:1. The capacity is increased, and more desiccant can be put in; 2. The position of the square temperature and humidity meter has been raised to ensure that the humidity can be seen directly when there is a <a target="_blank" href="https://www.printables.com/model/272099-bambu-lab-carbon-x1-with-ams-top-tool-storage" rel="nofollow noopener">toolbox</a> (https://www.printables.com/model/272099-bambu-lab-carbon-x1-with-ams-top-tool-storage) in front; 3. Smaller gaps to ensure that the silica gel particles will not fall out; 4. More dense openings and a reasonable internal transition layer ensure that it can be easily printed without internal support and opening support; 5. The narrower feeding port will not interfere with the feeding tray; 6. The bayonet of the feed port is tighter and has an anti-off device to ensure that the cover will not fall off easily.thanks for<a target="_blank" href="https://www.printables.com/@Fangoh" rel="nofollow noopener">@Fangoh</a> .This is the hygrometer what he purchased: <a target="_blank" href="https://www.amazon.com/dp/B08P3QJJZL" rel="nofollow noopener">https://www.amazon.com/dp/B08P3QJJZL</a> It worked perfectly.Version Information:V3.0 thanks for suggestion of <a target="_blank" href="https://www.printables.com/@Squawk_388463" rel="nofollow noopener">@Squawk_388463</a>, I remove some 'ribs' and have tested it. I upload the .3mf file, so you can print it directly.V2.1 Modified hygrometer position dimensions of “AMS dry box center” to accommodate more tolerances,and added a version without the hygrometer mount for PLA.(Advised by <a target="_blank" href="https://www.printables.com/social/140187-makerdog" rel="nofollow noopener">makerdog</a>)V2.0 The original version for publish.<h4>Buy me a coffee</h4>If you like my work, you can <a target="_blank" href="https://www.buymeacoffee.com/schongux" rel="nofollow noopener">buy me a coffee</a>. Appreciated !

Bambu AMS Silica Gel Dry box Hygrometer 

Dryer

Just_Josh

*I received a request to do a version without a baby.  I have added a new profile with the original mom/baby but now there is also a mother with an older child silhouette.   I also have versions with all layers combined (using supports) or split onto individual plates so they can be printed and combined.&nbsp;A nice mothers day mandala for the mothers in your life. This prints fairly quickly and it is easy to change the color for each layer as each of them are distinct objects in the assembly. Supports are needed but I was able to remove all of them in around 3-5 minutes. Some could possibly remain and not be seen if you aren&#39;t picky.&nbsp;If you like what you see please check out my other work <a target="_blank" href="https://makerworld.com/en/@Just_Josh" rel="nofollow noopener">https://makerworld.com/en/@Just_Josh</a>