Gärdi94

ninja

Wall mountable 4 remote control holder.Different heights to the compartments to store sifferent remotes,I made it taller & adjusted the pocket sizes from the original design<a target="_blank" href="https://www.printables.com/model/684683-remote-control-holder" rel="nofollow noopener">https://www.printables.com/model/684683-remote-control-holder</a>&nbsp;Should print fine without supports on the screw holes Resubmitted the .3mf to include all printers except the mini&nbsp;Wall mountable 4 remote control holder.Different heights to the compartments to store sifferent remotes,I made it taller & adjusted the pocket sizes from the otiginal design

Wall mountable 4 Remote Control Holder

Gadgets

Maxi

EN:This shaft-flight-system is modeled on that of the Target SYNC Swiss Point 01 (see pictures). The thread used is BA2 and can be screwed perfectly. I highly recommend printing with PETG due to its strength. However, with a very, very strong throw, it can happen that the rear part of the shaft-flight-shaft system breaks off on the thread. In this case, I recommend heating a thin screwdriver or similar with a lighter and carefully unscrewing the thread. If the support material causes an unclean surface on the upper part of the flight, it can be refinished with fine sandpaper.&nbsp;If you like the model, feel free to follow me. In the future I will create and upload other flights and the like.&nbsp;&nbsp;DE:Dieses Schaft-Flight-System ist dem des Target SYNC Swiss Point 01 nachempfunden (siehe Bilder). Das verwendete Gewinde ist BA2 und lässt sich perfekt schrauben. Ich empfehle aufgrund der Festigkeit sehr mit PETG zu drucken. Es kann dennoch bei einem sehr sehr starken Wurf vorkommen, dass der hintere Teil des Schaft-Flight-Schaft-Systems am Gewinde abbricht. In diesem Fall empfehle ich einen dünnen Schraubendreher oder ähnliches mit einem Feuerzeug zu erhitzen und das Gewinde vorsichtig herauszudrehen. Wenn das Support-Material eine zu unsaubere Oberfläche am oberen Teil des Flights verursacht, kann sie mit feinem Schleifpapier nachbearbeitet werden.&nbsp;Wenn dir das Modell gefällt, kannst du mir gerne folgen. In Zukunft werden ich noch andere Flights und Ähnliches konstuieren und hochladen.

Flight-Shaft-System (V1.1)

Dart

Sevro

OverviewThis is a boat model inspired by the TV series &#34;Thunder in Paradise&#34; from the 1994.It implements the Boat Model Components Kit 010It is great toy for pools.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000485141/design/2024-06-03_c8db7551d7f93.jpg"></figure>WarningDon&#39;t use brittle, old filament. Boat will be brittle too as it is hollow inside.&nbsp;Printing and assemblyTo obtain the best quality and simplicity of printing, I designed this model to be printed vertically with 0% infill.The engine is located inside the boat. Just put it inside. It holds firmly and is easy to insert and remove. This solution provides good balance and good looks, but does not allow for control. That&#39;s why I added the rudder. The rudder fits snugly into a hole under the boat and allows you to steer the boat. &nbsp;Additionally, I added the name &#34;Thunder&#34; to it as a separate part. If you want to give this boat a better look, simply print the name and stick it in the appropriate place on the side of the boat. Use superglue (Cyanoacrylate glue)For a better presentation of this model, I also designed a stand for the entire model.&nbsp;Three sizes.This model has three sizes. Big, medium and mini. You can choose which you want.Big version utilize capability of CarbonX1 in Z axis and is most majestic.Medium version is 10 % smaller than the Big one and is a little faster. Addicionaly in print profile there are two versions of hull (normal with flat bottom and full hull)Mini version is 23 % smaller than the Big one and is for small printers like A1 Mini.&nbsp;Have Fun&nbsp;&nbsp;&nbsp;&nbsp;

Gadgets

Dart

spielzeug