ForceM

andy

<p>Dies ist eine Schablone um Stäbchen auf einem Laser zu gravieren. Ich habe sie für Bamboogarden Hashi Stäbchen (https://fuchsgruppe.shop/bamboogarden/produkte/hashi-ess-staebchen/) konstruiert und probiert. Da es ein bisschen eng war beim ersten Versuch, habe ich im Modell die Kontur noch etwas angepasst.</p><p>&nbsp;</p><p>This is a template for engraving sticks on a laser. I have designed and tested it for Bamboogarden Hashi chopsticks (https://fuchsgruppe.shop/bamboogarden/produkte/hashi-ess-staebchen/). As it was a bit tight at the first attempt, I adjusted the contour a little in the model.<br> </p><p>LightBurn File: https://www.dropbox.com/scl/fi/xao8frvrknbv9wnehkfxa/chopstick-Vorrichtung-v9.lbrn2?rlkey=mrx06mck0j8prpvrqeg04a48f&amp;st=xa6ntv4t&amp;dl=0<br> </p><ul><li>Neues Modell V10 mit planer Schrift anstelle von erhobenem Text</li><li>New Version V10 is with flat font instead of raised text</li></ul>

Chopstick Laser Jig / Stäbchen Vorrichtung Laser

Sculpfun Upgrades

K-Studio.ca

<p>A tool to hold microfiber towel to clean build plates with ease.</p><ul><li>Print in PLA</li></ul><h4>Filament used in photo:</h4><ul><li>Bambu PLA Metal</li><li>Bambu PLA Matte</li></ul><h4>Updates </h4><p>March 23, 2024</p><ul><li>Added an alternative knob for thin cloth or sandpaper.</li><li>Original is designed to bottom out to prevent vertical force to break the print apart.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-23_13ab91d9f5c498.jpg"></figure><h4>Instruction</h4><ol><li>Simply take the two blocks align to the microfiber and cut to the same rectangle size.</li><li>Wrap the microfiber around the edge and crimp it down.</li></ol><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-23_6dbc3edb91bb7.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/754191/2024-03-21_757e6c3f7297d8.gif"></figure>

Build Plate Cleaner

3D Printer Upgrades

AU3D

<p>Secure your accessories on the IKEA Skadis board effectively with this tailored plug set. These plugs prevent unintentional detachment and sliding by fitting into a top hole partially obscured by the accessory. Available in sizes ranging from 2mm to 15mm, they accommodate a wide range of accessories.</p><p><br>I provide two options: with or without a handle. The version including a handle simplifies installation and removal but demands additional clearance, which may not be compatible with certain accessories. Moreover, this variant is more challenging to print and less discreet once installed. For these reasons, I personally favor the flat variant.</p><h3>Current limitations:</h3><ul><li>The accessory must partially cover a hole on the top edge.</li><li>The obscured hole's height should be between 2mm and 15mm.</li></ul><p>Future updates will address these limitations. Please be aware that the regular version needs 5mm of clearance towards the front for the handle, use the flat variant (separate print profile) if you don't have that clearance.</p><h3>Usage Instructions</h3><ol><li>Installation<ol><li>Measure the exposed height of the hole covered by the accessory, or print a variety of sizes for trial and error.</li><li>Choose the correct plug size based on your measurement. If in doubt, select the larger size for a more secure lock.</li><li>With the accessory in place, insert the plug into the hole by pushing, ensuring the embossed size number faces front. Ensure contact between the plug and accessory for optimal stability.</li></ol></li><li>Detachment<ol><li>For smaller plugs, use pliers or fingernails for removal.</li><li>Squeeze the sides of taller plugs and pull (only for the regular variant with handle). Use pliers if necessary for a better grip.</li><li>Note: These parts are delicate, expect some losses during removal.</li></ol></li></ol><h3>Background</h3><p>I had some accessories with poor grip which detached or wiggled when pulling something out of the part (bottle trays, hooks, battery holders, etc). This issue may arise from several factors: poor design, variations in the finish of Skadis boards (notably, the black boards seem slightly thinner), or manufacturing tolerances. Modifying the original models can be time-consuming and may not always be possible, leading to the creation of this simple, universal (within current constraints), and easily printable solution.</p><h3>Printing Instructions</h3><ul><li>Brims are added for improved adhesion due to the delicacy of the plugs.</li><li>Carefully remove the brim to avoid damaging the plug.</li><li>While PETG is recommended for its properties, PLA has been tested and found satisfactory.</li><li>Handle gently to maintain integrity.</li></ul><h3>Skadis Collection</h3><p>I am constantly developing more IKEA Skadis attachments. Check out my <a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/188108" rel="nofollow noopener"><strong><u>IKEA Skadis Collection here</u></strong></a>.</p>

Sculpfun Upgrades

3D Printer Upgrades

Ikea