FkoNL

3D Print Bros

V2 of the Gyro Fidget Spinner is here! Please use the print profile for best results. Bambu Labs Basic PLA gives me the best results, but most PLAs should work just fine. My prints got spinning right away, but if your rings don&#39;t spin freely, first try breaking it in a little. If it doesn&#39;t break in within a few minutes, re-print it with reduced flow ratio or perform flow calibration. Results will vary depending on filament used.&nbsp;Improvements include:<ul><li>Relocated Z seams</li><li>Optimized tolerances</li><li>Longer spin times</li><li>Quieter smoother spinning</li><li>Faster print time</li></ul><a target="_blank" href="https://cults3d.com/en/3d-model/game/gyro-fidget-spinner-v2" rel="nofollow noopener">Commercial selling license now available!!</a>&nbsp;Check out the JUMBO version <a target="_blank" href="https://makerworld.com/en/models/393051#profileId-294200" rel="nofollow noopener">here</a>! Or if you&#39;re more a miniature person, I have you covered with the <a target="_blank" href="https://makerworld.com/en/models/435704#profileId-340795" rel="nofollow noopener">Micro</a>.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000245471/design/2024-04-19_89ff840145366.gif"><figcaption><a target="_blank" href="https://makerworld.com/en/models/393051#profileId-294200" rel="nofollow noopener">JUMBO Gyro</a></figcaption></figure><figure class="image image_resized" style="width:43.04%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000245471/design/2024-04-19_4d5bdcba3287d.gif"><figcaption><a target="_blank" href="https://makerworld.com/en/models/435704#profileId-340795" rel="nofollow noopener">Micro Gyro</a></figcaption></figure>&nbsp;

Gyro Fidget Spinner V2

Printed

SkubOpMakrel

A simple mount for the most common Makita charger. Just remove the four rubber feet and press the charger down onto the pegs on the mount, simple as that. Can be mounted in all directions due to being press fit.&nbsp; Questions are welcome and please like, rate and share.

Makita charger wallmount

Interessant

Kt's Glitter Bar

Ikea Symfonisk Speaker Wall MountToolless and no hardware assembly, optional filament channels used to lock in place.I designed this after struggling to find a design that didn't require nuts/bolts, didn't required 8 hours of print time, and seemed robust enough to be wall mounted.All parts for 1 speaker print on a single plate in about 4 hours. Brim is recommended due to large flat surfaces prone to warping. Only one section requires minor bridging and it is hidden after assembly. Tolerances are pretty tight to ensure a stable fit.&nbsp;3 wall loops for strengthSuggest 3+ bottom/top solid layers15-35% infillSuggest ABS/ASA but will probably work with other filaments&nbsp;Left/Right angle is adjustable in 22.5deg incrementsUp/Down angle is selectable at 1deg, 18deg, or 30deg - can add additional variants if needed

Ikea Symfonisk Speaker Wall Mount - Toolless, No Hardware, No Supports, Single Plate

To Print

BamBam Design

I designed a Rework for Ø14 balls =&gt; <a target="_blank" href="https://makerworld.com/en/models/467064" rel="nofollow noopener">Marble Castle Rework</a> Marble Castle is a functional, easy printable Toy.Push the Button to let the marble climb the stairs and rotate the knob to rotate the house to let the marble go further.<figure class="image"><a href="https://youtube.com/shorts/QdsTP92-YdE?si=bcDz2RN6pgaiTwnn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000060986/design/2023-11-17_13919cbb8fa5a.gif"></a></figure> What you need to assembly:<ul><li>Spring Ø4 from an ballpoint pen (Cut it to around 15mm)</li><li>7mm-10mm marble/steelball, Ø9 works best for me!</li><li>small rubber band</li><li>optional 2 pieces Ø10x 3mm magnets</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000060986/design/2023-11-09_8b9ecbe98edda.png"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000060986/design/2023-11-09_a1623981d712f.png"></figure><figure class="image image_resized" style="width: 64.07%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000060986/design/2023-11-09_36b4883890de.png"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000060986/design/2023-11-09_38d6fef21e5e5.png"></figure>&nbsp;A like &amp; follow costs nothing just like the 3D model! Thank you 🤗&nbsp;Update 10.11.23<ul><li>Added a revision hole in the base for spring mechanism</li><li>optimized some clearance</li></ul>Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Marble Castle - Desk Fidget Toy

Anne - favorieten

Kohen

<h4>Summary</h4>I designed this tool for removing and installing the plastic piston sleeve of the 2000 onward La Pavoni leaver espresso machine. It has worked well for me, I have also seen people use it for older gen models too with metal sleeves, though I can't comment on which other models it may fit. I have added a hole to insert a Phillips head screw driver if you need extra leverage but this feature is untested by me so be warned.Make sure you print this either solid or with a high wall count to the point where the teeth (that engage with the sleeve) are solid in the layer preview.&nbsp;Cheers!&nbsp;<ul><li>Notes:</li></ul>PLA, PLA +/tough, PETG should all work.&nbsp;I printed this with a 0.6 nozzle 0.3 layer height with 5 outer layers (vertical shells) this is to give the teeth enough strength. A thicker top shell layer number will also help. I used infill of around 10% and it took 2 hours on my prusa.If you're using a .4 then I'd recommend 7 or 8 outer layers.&nbsp;If you want to go easy mode, just print it with 100% infill at in should be very solid.I recommend using a larger nozzle like the .6 to get well bonded layers.Make sure you print it in the orientation shown below with the base of the handle flat against the print bed.&nbsp;