Eraser-FX-

blecheimer

Describtion: There are a lot of AMS risers on makerworld and I looked at all of them. Most of them have the same issue: They are large, beefy and need supports to be printed - that means lots of filament are necessary. I wanted a riser, that uses less than one spool of filament, is very robust, lets me open the top cover so that it stays open for ventilation, has a sufficent opening at the top to work on the printhead and of course has enough room for the AMS. So I designed my own AMS riser. It is so robust that I can stand on it. With my print settings (see below) it uses 840gr filament and can be printed in about 24 hours. All my settings and the part arrangement on five plates is included in the 3MF file. A step file for your own modifications or remixes can also be downloaded.&nbsp;Dimensions: 409 x 369 x 87 mm 840 gr&nbsp;Material: I recommend a sturdy filament like PLA, PLA+ or PLA-CF. Maybe PETG will work but the stationary tensile strength of PLA is just higher. I have chosen PLA-CF from Eryone because I always wanted to try it.&nbsp;Print settings: You can find my settings in the 3MF file together with the part arrangement on five plates. With my settings the print time is about 24 hours and you will need 840gr filament. for the parts: 4 walls 5 tops 5 bottoms 25% adaptive cuboid infill 0.2mm layer height no support for PLA-CF (Eryone) Nozzle: 0.4 mm Nozzle-Temp: 225°C Bed-Temp: 60°C Cooling: 100% @ second layer onwards Volumetric Speed: 12 mm³/s Outer Wall: 150mm/s Inner Wall: 250mm/s Infill: 200 mm/s Top Surface: 150 mm/s Bridge: 50 mm/s&nbsp;Assembly: Put the parts of the lower half together using the provided connectors. I highly recommend that you use superglue or 2K expoy on the part interfaces for extra stability. Do the same with the top. Then slide the top half on the lower half and secure it with glue. The designed gap between the parts is 0.15mm - that should be no problem for a Bambu printer.&nbsp;&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by-nc-sa/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY-NC-SA 4.0</a> You are not allowed to copy this model to other 3D printing websites without my permission.

Robust AMS Riser - printable without support

Bambu

SpectreGadget

If you like this model, please throw me a like. Designing these models takes time, filament, and caffeine. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=AESRCQSQW6TS2" rel="nofollow noopener">If you want to support my work, please buy me some caffeine.</a> Thanks!&nbsp;Same model, just 'painted' using BambuStudio for printing on BambuLab printers with an AMS for four color printing. I used Microcenter Inland brands: White PLA+, Blue PLA+, Black Silk PLA , Silver Silk PLA, True Red PLA+BTW, I painted silver in the panel crevices to give add additional depth to the model when printed. Not really ‘standard’ but i like out it came out.Best to optimize your flushing volumes! With tuning, this model's print time can be reduce by hours with optimized flushing volumes.&nbsp;*Update 7/29/23 - Updated R2D2.3mf to include the leg and foot pins I created and used on mine. For the middle foot, I just used some wire. Added the two files separately for easier download.

R2D2 Alexa Echo Dot 3 Dock (Colored for AMS)

Nice

Bastien

WORK IN PROGRESS&nbsp;First, I want to thank 86duino the original author for his excellent work, we can find it on <a href="https://cults3d.com/en/3d-model/game/super-mario-complete-set" rel="nofollow">cults</a> and <a href="https://www.thingiverse.com/thing:1991111" rel="nofollow">thingiverse</a>.I really like the work done but the watermark completely “distorts” Mario...so I made the following changes:<ul><li>removed watermark on the right leg</li><li>removed watermark on both gloves</li><li>removed watermark behind the head (this one was hidden, I realized it after)</li></ul>&nbsp;<ul><li>added “marks” on gloves</li><li><img src="https://media.printables.com/media/prints/487664/rich_content/2918283e-84fb-4d94-8272-a13ee567dc90/capture-decran-2023-05-22-a-193747.jpg#%7B%22uuid%22%3A%2289ec36c1-5270-4cd7-8e3d-0c4ba56782cb%22%2C%22w%22%3A880%2C%22h%22%3A876%7D"></li><li>added theeth to the smile</li><li><img src="https://media.printables.com/media/prints/487664/rich_content/ae1009aa-d035-45cb-82fe-0486875c8621/capture-decran-2023-05-22-a-195422.jpg#%7B%22uuid%22%3A%225e733898-a9cf-48c2-8674-2a169464d138%22%2C%22w%22%3A652%2C%22h%22%3A632%7D"><img src="https://media.printables.com/media/prints/487664/rich_content/22b09f86-cf87-4aa5-bcc1-1f1f5c150682/capture-decran-2023-05-22-a-200526.jpg#%7B%22uuid%22%3A%223e190a02-e97f-42be-b6d8-44030a460341%22%2C%22w%22%3A1438%2C%22h%22%3A766%7D"></li><li>added fully printable eye</li><li><img src="https://media.printables.com/media/prints/487664/rich_content/83cfe222-39c7-493a-a598-2f522d0a33c0/capture-decran-2023-05-22-a-195707.jpg#%7B%22uuid%22%3A%22f505f3a3-1c26-47f4-8786-00a38395428a%22%2C%22w%22%3A652%2C%22h%22%3A632%7D"><img src="https://media.printables.com/media/prints/487664/rich_content/64ed3ab1-8fb6-43d4-8423-eed108283393/capture-decran-2023-05-22-a-200448.jpg#%7B%22uuid%22%3A%22378b6dac-0ef3-4fec-b57a-8a0c2baa0637%22%2C%22w%22%3A1350%2C%22h%22%3A884%7D"></li><li>added fully printable logo M</li><li><img src="https://media.printables.com/media/prints/487664/rich_content/dbc7bf7b-c6b3-4c00-8bbb-0b45b730c8a3/capture-decran-2023-05-22-a-195747.jpg#%7B%22uuid%22%3A%22d778452b-27d8-46ed-a02e-0deecc17a055%22%2C%22w%22%3A652%2C%22h%22%3A632%7D"><img src="https://media.printables.com/media/prints/487664/rich_content/2aa0e20b-b2ae-43ea-b513-e3e65254dab0/capture-decran-2023-05-22-a-200556.jpg#%7B%22uuid%22%3A%2203de00f9-7ca4-427f-8ff5-af70a5856f97%22%2C%22w%22%3A1534%2C%22h%22%3A766%7D"></li></ul>I have a multi-material printer and was able to print the mouth, eyes and M logo by painting from the Slicer, but I also printed a <a href="https://www.thingiverse.com/thing:2939398" rel="nofollow">Luigi where the author</a> had separated all the colored parts for everyone to print. As a result I created an assembly version of Mario by separating the M logo from the cap in 2 parts, the eyes in 3 parts and the mouth in 2 parts.&nbsp;There is 2 folders:<ul><li>Painting or MMU contains the closest files to the original, only the watermarks have been removed and the gloves have been modified</li><li>Multipart contains all the modifications but also the eyes, the mouth and the logo in several parts</li></ul>The tolerances can be different depending on the calibration of your printers, make a test by printing the 3 parts of the eyes.The model is 90cm high, happy printing

Mario reworked (no watermark)

Modell

AP Engineering

Remixes Available for other Food Dehydrators:<ul><li>Silvercrest 350W / Quigg 350W Food Dehydrator: <a target="_blank" href="https://makerworld.com/en/models/14105" rel="nofollow noopener">https://makerworld.com/en/models/14105</a></li><li>MisterChef® Professional Food Dehydrator, 250W: <a target="_blank" href="https://www.printables.com/model/499723-2-spool-dryer-base-for-us-model" rel="nofollow noopener">https://www.printables.com/model/499723-2-spool-dryer-base-for-us-model</a></li></ul>16/05/2023: Added Assembly manual to support assembly._________________________________________________________________________________________________________I was using a generic food dehydrator as a filament dryer (Muhler DHY-500T). It was not very handy to use to dry filament because the spool sits its side, and was weird to put it in and out and I could only dry one spool at a time, which was not very energy efficient. So I took out the electronics from the dehydrator and designed a box from scratch.&nbsp;This is a fully functional 2 spool food dehydrator with a 250W motor (in my case it's 250W, but there are food dehydrators ranging from 150W to 450W). As expected, please use PETG or above (ABS, ASA, etc) to print all the parts since the temperatures should be above 50degC. For the feet you can print in PLA, but I advise in TPU for a nicer feeling. I also included in the rear a nice power cord lock, so even if you pull it up strong it won't rip anything. The lid on the top opens with two hinges in the back, for this M4 Screw and Heated brass inserts is needed, but if you don't have brass inserts you should be fine just with a long M4 bolt and a M4 nut.&nbsp;I included the STEP file in case the electronics of your food dehydrator doesn't fit on those holes you can easily modify it to fit your electronics.&nbsp;This filament dryer is compatible with filament spools as big as 21.5cm (exterior diameter) & 8.5cm (thickness)! So should be compatible with any filament spool available. There's also plenty of space to put some silica bags to keep the humidity down.&nbsp;BOM: Mandatory:<ul><li>Food dehydrator (should be quite generic) - You can buy these used from 5$ to 15$ max</li><li>4x Bearings 608 (608 / 608rs / 608zz, etc…)</li><li>Round Cheap Hygrometer - 2$ for a pair (Search AliExpress “Mini hygrometer”)</li><li>2x Heated Brass Insert M4 (any lenght) and 2x M4 bolts (any lenght above 10mm) OR 2x M4x25mm bolts + 2x M4 nuts - For the hinges</li><li>2x PTFE Tube (to feed filament out of the dryer)</li><li>2x zip ties (to lock the PTFE tube)</li><li>Self tapping screws to lock the electronics in place, to lock the power cord.</li></ul>Optional:<ul><li>5mm heating insulation pad to cover the whole inside walls and increase the heating capabilities and efficiency.</li></ul>If you enjoy it, consider tipping (any amount, even 0.05$ is appreciated) to my Paypal (affp_93@hotmail.com) to keep funding more nice projects like this. Even if you don't feel like donating, putting a like and dropping a appreciation comment goes a long way to support it!

2 Spools Printable Filament Dryer

3D Drucker

DonMatis

I present to you one of my favourites so far....the Biomechanical Skull!&nbsp;Highly recommend to print this with a tight brim and 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used:<ul><li>PLA Overture Black</li><li>PLA Overture Chocolate Matte</li><li>PLA Overture Chocolate</li><li>PLA Overture Brown</li><li>PLA PolyTerra Peanut</li><li>PLA+ Esun Bone White</li><li>PLA PolyTerra Cotton White</li><li>PLA Overture White</li></ul>Swap Instructions:<ul><li>Start with Black</li><li>At layer #8 (0.72mm) swap to Chocolate Matte</li><li>At layer #10 (0.88mm) swap to Chocolate</li><li>At layer #14 (1.2mm) swap to Brown</li><li>At layer #18 (1.52mm) swap to Peanut</li><li>At layer #24 (2mm) swap to Bone White</li><li>At layer #28 (2.32mm) swap to Cotton White</li><li>At layer #40 (3.28mm) swap to White for the rest.</li></ul>

Bambu

Nice

Modell

3D Drucker

Kunst