E-Man

SavageLau

I am having issue with put my build plate on my A1.The original guide does help aling the build plate, but I feel like those two on the side does not help that well, since it is so low to the printer bed. So I made this build plate aligner deisgn to help easier put you build plate down.&nbsp;Due to the nozzle prime brush located on the left, and nozzle have travel a lot of the left, I don't think it worth the risk to put anything on the left. Plus, this one on the right side is already good enough to help you locate the build build.&nbsp;It cost very little filament, less than 5g. Around 19m printing time. Suggests print at least with PETG, or ABS.&nbsp;&nbsp;<h2>ATTENTION! If you are firmware version 01.01.50.24 or above, do not use other people's printing profile, model is not longer compare after firmware update. </h2>&nbsp;<h2>Update 1/27/2024: New model updated, name “for 01.01.50.24 firmware”. </h2><h3>New firmware version: 01.01.50.24(beta) will cause issue. I have found nozzle clumping detection cause the issue. It is automatically enabled after firmware update. But no option to disable it currently. More information from Bambu Wiki: </h3><h3><a target="_blank" href="https://wiki.bambulab.com/en/a1-mini/manual/nozzle-warp-detection" rel="nofollow noopener">https://wiki.bambulab.com/en/a1-mini/manual/nozzle-warp-detection</a> </h3>&nbsp;<h3>Issue description: </h3>After update firmware 0.1.01.50.24. Print stops randomly in the middle and error note shows: <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-27_271f7f17e33c4.png"></figure> Nozzle will park on the aliger area and cuase issue. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-27_b0eecdf4e5003.png"></figure> According to BBL Wiki: "1. After printing all the walls of the first object on the third layer of this plate, the tool head will move to the position of the purge wiper for the first detection. The specific coordinates of the nozzle during detection:  A1 mini (X-6, Y 170, Z-1); A1 (X 261, Y 250, Z-1). The detection process is shown in the following figure. " &nbsp;<h2>Install guide:</h2>Align from the back, push the aligner pin into the bolt hole under the build plate.Confrim top part is all the way in.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-04_7cd7e48eb7b47.gif"></figure>&nbsp;&nbsp;Many revisions was made and many tests was done to confirm it not only works but also get good fit and finish:<figure class="image image_resized" style="width:55%;"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-05_2c006911bca8.jpg"></figure>&nbsp;<h2>Material:</h2>Highly suggest to print with ABS or better heat resistant material. PETG Will works. PLA is not recommaned.I also made cut line design on alginer, those cut slots should help guiding the direction when thermal expansion and retraction happen. Which it should bond on the printer bed more if thermal deformation occurs.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461583/2024-01-04_ec38222ff07b3.png"></figure>

A1 Build Plate Aligner

Printer mods

Snail

lettering raised by .8mm respectively for easy color swaps.&nbsp;You might like my other signs check out my <a target="_blank" href="https://www.printables.com/@Snail_396985/collections/1265836" rel="nofollow noopener">collection</a>&nbsp;<h3>** Unfortunately MakerWorld doesn't allow me to link you to my commercial printing license, I do have one however as I am a professional. If anyone is interested in contacting me in regards to the license or about the designs themselves you can find me @Snail on Printables. That is mainly where I am active, comments on my makerworld profile will likely go unanswered. </h3>&nbsp;

Chuck Norris Fact. Mini Sign.

signs

Black Glovz

Use 0.35 or 0.4mm first layer width

Knife Keychain

to print 

makerdavid3d

<h2><img class="image_resized" style="width: 72.23%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000485550/design/2024-06-14_034909419f05c.png">CANNON HOLD MODEL</h2>&nbsp;

CANNON OLD MODEL HYSTORIC  MORTAR ARTILLERY

Bang💣

geoffrey.holland

First effort designing a building with texture.The three stl files are the building with different added texture.Category: Toys & Games

Printer mods

signs

to print

Bang💣

Notgrass